AR5 BIGGIE Contents Safety instructions Page For the electrical installer 30 For the kitchen furniture installer 30431 Before installing General 32 Appliance description 32 Technical data: — Dimensions 32 Electrical connection values 33 Fan outputs 33 Air outset-exhaust air 34135 Accessories/installation materials 36 Preparing to install — Preparing for exhaust air operation 36 Preparing the wall box (exhaust air operation) 36 — Position of exhaust air opening 37438 Special accessories Exhaust air hoses 39
For the electrician For the kitchen furniture installer 30 Safety instructions Mounting the power point immediately above the extractor hod, above the hanging cupboard over it or inside the flue cover, has two advantages: 1. the power points out of sight 2. it you dean to, you can easily cut the power o the appliance by pulling the plug out of the socket.
SIKKIM 9189 — BIKM3B/S0 GB/EU Irs doubtful cases, please seek the advice and consent of the competent area chimney-sweep or the local building authorities. Since, In spaces without fireplace, the rule Js: “Supply alr opening as large as exhaust air opening”, the efficiency of the exhaust sir device may he impaired by the greater opening of 500600 cm? Operation of the hood as a return air hood In such circumstance sis safe and is not subject to the regulations noted above.
General Appliance description Technical data 32 The fume extractor hood is supplied as an exhaust air appliance and may be used as a turn air appliance through application of an ache carbon filter (special accessory). For this purpose, you need the AEG Original Active Carmen Filter (see special accessorize.
TOME 7092 TOMB /92 GB/EU Electrical rating: 850D 8308 D Total rating: 185w 185W Fan motor: 170w 170w Lighting: T x 15W T x 15W {Strip light) (Strip tight) Fan performance (in stages) as defined by DIN 44971 850/8509 D Stage” Stage Stage Staged Air extraction: 150 m¥%h 280 m3h 360 m¥h Bimini Circulation: 130 m¥/h 250m%h 330 mh 440 mi/h Alr outlet system diameter 125 mm Please note that the MKZ wall box mentioned in these instructions is not available in the UK.
Air outlet Dimensions of appliance and niche 34 Air outlet upwards in the middle Pipe connector for 126 mm diameter for exhaust air hosepipes of 125 mm diameter.
Preparing the air outlet Preparing the wall box {exhaust air operation} 36 Accessories / Installation material outlet pipe {telescopic connection ventilation grilles angled connector nor-retumn flap outlet pipe retainer hose-pipe 125 mm x 800 mm S8 wall-plugs for tautening the outlet pipe retainer wood-screws complying with DIN 7896 for fastening the cutlet pipe retainer 28 %65 mm self-tapping screws complying with DIN 7981 for fastening the outlet pipe 86 wall-plugs for fastening the telescopic connection
EUGENIE The dimensions and position of the air outset opening are given in the following diagram 850D Position of exhaust air opening 37
ALY /30 VOID BB BIGGIE For wall box/fume extractor hood connection, it is best to use the non-flammable exhaust air hose under E-No. 610 898 008 {125 mm dia ) from cur range of special accessories. The extractor hod can be used as a re-circulating hoed i no air-shaft or outside wall is available. For use as a re-Circulating hood it Is necessary to it 2or 4 KK 60/80 active-charcoal fitters, E-No. §10 899 480 for absorbing cooking fumes.
Preparing for exhaust air operation 40 if the fumes from the kitchen are to be led out into the open air, you will be needing a telescopic wall-box with the part-number e-Nr. 610 BES 004 {special optional extra}, (Fig. CJ} Refile the back-pressure flap and secure it by turning it. For the connection hood best use the non-combustible exhaust air pipe of 125 mm dia, e-Nr. 610 899 008 {special optional extra).
SCHWA 1092 GRAY Mounting on the wall: The overall height of the extractor hood can be altered by means of the compensating pipe “B”. A bag of accessories containing wall-plugs and screws as well as screw clips and fastenings is enclosed with every extractor hood. The drilled holes for the screw hooks are located as shown in the sketch. The extractor hood is hung on the screw hooks and can be adjusted afterwards 1o the correct height.
Installation work for operation with recirculating air The fie hooding plate is fitted into the notches in the upper extractor hood opening for the purpose of increasing rigidity. Arrangement of the fastening elements on the surface of the wall against which the rear face of the hood is ing. To 1t the compensating piece "B”, two wood screws are screwed into the wall at a distance from the ceiling.
MAT 082 BIGGIE The exhaust air can be taken out through the fie into the open air o else upwards (work 10 be done on site), The compensating piece “B” must be fitted as described in the section on operation with recirculating air. The back-pressure flap and the flexible hosepipe are connected 1o ong another with the outlet connectors of the extractor hood. The protective foil is removed from the sealing strips fitted at the upper inner edges of the flue.
Hello 44 Allow me to introduce myself: | am your new AEG fume extractor hood. From now on, 1 should Like 10 help you keep your kitchen free rom fume and {at deposits. Not simply because of my attractive appearance, but also thanks to my “infringe qualities” tam economical in terms of energy consumption, quiet, power, easy 1o operate, and simple to care for. f you carefullest read and follow my operating instructions (maintenance) before first use, you are sure 1o be extremely satisfied with me.
SKIBOB 11/89 ~ AMBUSH 997 GEL Safety instructions 1t must be ensured that hobs are always covered so that the appliance is not damaged by excessive heat liberation. Open fireplaces on oil-, gas-, and coal fired cookers must be avoided. During deep-frying over a cooker/hob, the appliance used for deep-frying must also be supervised during operation.
Operation 46 Starting up My sliding switches are arranged on the life-hand side (when rooked at from underneath). The various numbers and symbols have the following meanings {listed from the front to the back): I Lighting on Lighting off Lighting = Fan settings switch 1 = Fan setting 1 4 Fan setting 2 3 Fan settling 3 4 = Fascinating = high-speed setting [EU_] To turn the extractor hood on, set my switch for the fan to "On” M. The extraction hood fan will now start tanning.
QI B89 ~ WEFT-3 881 — W 089 GABFEST ‘The bulls-in fume extractor hood is to be switched on before cocking begin and allowed to run on around 15 minutes after cooking ls completed. You should remove my metal fat litter (Fig. EW) from the appliance every §--8 weeks and wash it by hand or In your dishwasher. The active carbon fighter must be changed not later than after 1 year. The active carbon fitter cannot be washed or regenerated.
Cleaning the metal grease filter To remove and then clean my metal grease filter grills, please proceed as folios: As a safety precaution against my being switched on by mistake, take my fuse out or switch off my contact-breaker in the {use-cupboard. 1. Press the catch on the grease filter grill inwards, and take the grease tillers out at the front and the back. 2. Clean the inside of my housing only with warm washing-up suds (do not use any abrasive cleaning products, brushes, or scouring powder) 3.
WAS Q92 BIGGIE To take out and replace the 60/80 active-charcoal litters, E-No. 610 899 480 (special accessories, at an extra charge), proceed as follows: In order to naval unintentionally switching on, screw my fuse out of its holder or take my fuse out of your main fuse-ho. 1. Press the locking bolt on the metal grease filter grill 1o the inside and remove front and rear fat filters. 2. Take the old active-charcoal filters out by unlocking them like the fat filters. 3.
Replacing Strip-tight {Starter) 50 4. Fit the new KK 60/80 active-charcoal filters. in 850 D, insert hemming staggered at a 90° angle against the lat filters and let hem engage. In 8508 D the cal filters are fitted like the fat filters. 5. Se crew the fuse back in or replace the fuse in the main fuse box. The extractor hood is now once again ready for use as a re-circulating hood! You can replace the strip-lights or the starter yourself. Be tors you start, disconnect the appliance from the mains. 1.
Wall T2 LYELL Caution: only ever insert the same type of strip-light, with a maximum of 18 watts, Fit it into the mounting and turn it to the right. 3. i the starter is selective, sake it out of the mounting by meningitis left. Insert the new starter by turning it to the right. 4. Fit my lighting cover back into position.
Cleaning 52 important! To clean the fume extractor hood, DE-energize the appliance {e.g. pull out the mains plug). Never introduce sharp objects into the protective grille of the motor! Clean the outer parts with & mild washing-up liquid solution. Never use abrasive cleaners, brushes, or scouring agents. Clean the control panel screen and fat filter grief only with & damp cloth and mild washing-up liquid solution. It is important to observe the filter change of cleaning intervals.
SZHOS8/92 DDS 9/89 GRUYERE $Special accessories and optional extras Activated charcoal filter E-No. 610 889 480 KK 60/90 MKZ wall box E-No. 610 883 004 Height and width in mm Dimensions for opening 250 x 220 210 = 185 Exhaust-air hosepipe, £-No. 610 898 008 125 mm diameter, aluminum Customer service In case of any inquiries and faults, please call our service center {see list of service crescent. When calling, please state the following: 1. The medal designation 2. The E-No. 3. The F-No.
four appliance has a fault, please contact our service engineer and state the following numbers: AEG Tannhauser AG Poaching 1036 0-8500 Nirenberg 1 @ Copyright by AEG H 260 251 000 02831407 02 AEG Domestic Appliances Ltd Customer Care Department 5877 High Street Slough Berkshire 8L1 1DZ Telephone: 08705 350350
