INSTRUCTION BOOK 6310 K-m 1 ZA GB 949600455
Congratulations from AEG Dear Customer, Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked . These are warning texts to help you avoid accidents. Keep the operating instructions.
Table of contents Contents Page no For the user Congratulations from AEG ......................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 5 Control button ....................................................................................... 5 CHEC .....................................
Safety information Never use plastic or aluminium dishes on the hob. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Never leave the hob unattended while deep fat frying, or heating fats and oils.
Description of the product Control button CHEC Panel Controlbutton for operations 5
means that you do not have to adjust the heat constantly. CHEC control provides the zones with the following functions: Ceramic glass surface The ceramic glass surface has four cooking zones. When a zone is turned on, it will illuminate at various intervals depending on the heat setting selected. Even at the highest setting the zone is disconnected occasionally to ensure that the surface is not over-heated. The glass is hard, and has been tempered to withstand heat, cold and temperature shocks.
Before use Connection of child safety device on zones Turn the 2 control buttons to at the same time. The display will show: When you turn on a zone the display will show: To turn on a zone, turn the 2 control buttons to at the same time. You must then activate one of the zones within 10 seconds. The light under the symbol in the display will disappear. You can disconnect the child safety device permanently as follows: 1. Turn the 2 control buttons to and return to 0. 2.
Protection of the glass ceramic surface A protective film should be applied to the glass ceramic surface before use. This will make it easier to clean the surface, as well as preventing substances from being burnt onto the surface. This is what to do: 1. Pour a few drops of ceramic cleaning detergent such as vitroclen onto a piece of kitchen roll and rub the detergent into the entire surface. 2. Polish the surface with a clean cloth until it is dry.
How to use Switch symbols (to the left) control for regulating the small cooking zone at the rear control for regulating the double cooking zone at the front. control for regulating the large cooking zone at the rear control for regulating the small cooking zone at the front. Regulating The regulation of heat is step-free for all plates on a scale from 1 to 9. “1” Represents lowest heat “9” Represents maximum heat. “0” Represents “OFF”.
Residual-Heat indicator When you switch off a zone, an "H" in the display indicates that the zone is still hot. The residual heat indicator will continue to be illuminated as long as the temperature exceeds 80˚C. Cooking zones The control knobs are continuously adjustable from 1 to 9 (9 is the highest setting). There is AUTOMAX control of all settings, enabling you to set the setting required from the outset. Please see the table of settings.
CHEC control Autostop If you forget to turn a cooking zone off after use, it will be disconnected automatically after a specific period of time. The higher the setting, the shorter the time before the zone is disconnected. Setting 1 2 3 4 5 6 7 8 9 AUTOSTOP 6 hours 6 hours 5 hours 5 hours 4 hours 1½ hours 1½ hours 1½ hours 1½ hours When the autostop function is activated the display will show: The zones cannot be used. Turn all the control buttons to 0. The zones can now be used.
Recommended settings when using AUTOMAX The use of AUTOMAX means that the maximum power is connected for a specific number of minutes, depending on the setting chosen. The table below shows the length of time for which there is full power for each setting, and the functions for which each setting is suitable. Setting 1 2 3 4 5 6 7 8 9 Full power time (minutes) 1 minute 3 minutes 5 minutes 6.5 minutes 8.5 minutes 2.5 minutes 3.5 minutes 4.
Disconnection of AUTOMAX: If you do not wish to use AUTOMAX, observe the following procedure: 1. Turn the control button to AOFF. 2. Then turn the control button to the required setting. Setting the large zone on the double zones 1. Turn the control button to The display will show: 2. Then turn the control button to the required setting (e.g. setting 9). If you wish to disconnect the large zone, turn off the zone and then turn the control button to the required setting.
When you turn on a zone the display will show: Observe the following procedure to use a zone: 1. Turn the 2 buttons to at the same time. 2. Use one of the zones within 10 seconds. The light under the symbol in the display will disappear. You can disconnect the child safety device permanently as follows: 1. Turn the 2 control buttons to and return to 0. 2. Turn one of the 2 control buttons immediately to .
over will burn onto the hot cooking zone. Advice and hints for using the cooking zones If you use the advice below you will save energy and make your cleaning tasks easier. Saucepans with very shiny/bright bases will prolong the cooking time slightly compared with cooking utensils with matt/dark bases. Adjust the cooking zones correctly. Select the highest setting for the cooking zones until the food is brought to the boil. Then reduce the setting as far as possible, without the food going off the boil.
Check whether your cooking utensils has level bases by placing the item in question upside down on a work top and positioning a ruler on the base. A curved base, both inwards and outwards, will prolong the cooking time and increase the energy consumption. If the diameter of the base is too small, the energy consumption will increase, and any food boiling over will burn onto the hot cooking zone.
Cleaning and maintenance of For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. Splashguard The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram. 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface”. Be aware of the two retaining pegs, which are sharp. 4.
Stainless steel surfaces Clean the appliance after use with a soft cloth well wrung out in warm water, use a small amount of liquid detergent for stubborn soiling. Stainless steel parts may become straw coloured with use, use a proprietary stainless steel cleaner to remove this straw discolouration. Never use metal wool, metal sponges or other abrasive cleaning agents. The ceramic glass hob 3. Wipe the ceramic hob clean with a damp cloth or kitchen roll.
Tips on the use of the ceramic hob unit Do not slide saucepans across the surface of the hob - always lift the pan when placing it on, or removing it from the ceramic surface. Wipe the bottom surface of the pots and pans with a clean dry cloth before placing them on the ceramic surface. This helps to reduce cleaning and prevents scratching the hob glass. Wipe off spills whilst the hob is warm. Select the highest setting for the cooking zones until the food is brought to the boil, then reduce the setting.
The decorative pattern on the ceramic surface can become scratched and marred with use, depending upon maintenance, but does not adversely affect performance. Such blemishes are not covered by the warranty and do not affect the operation of the hob. Spills and melts must be removed immediately, while the surface is still warm, using the scraper supplied with the unit.
Mounting Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation Min. 47 mm The appliance unit can be mounted in any type of kitchen with a work top whose thickness is between 28 mm and 40 mm. Clearance The distance between the top side of the work top and the carpentry underneath must be at least 47 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the work top.
It is not necessary to attach the reinforcement beam to the work top surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges.
Electrical installation The electrical connection may only be performed by a qualified electrician/ competent person. The electrical connection must be carried out in accordance with prevailing regulations for appliances using heavy current. The connection must comply with any specific requirements specified by the local electricity supply authority. There must be no interference with any of the unit’s electrical parts. The cable is mounted in the pegs as shown.
Two-phases zero-earth Cable type 1,5 mm² HO5VV-F. The cable outside diameter must be between 7,5 and 10,5 mm. Technical data Cell Voltage 230 V Electrical connection 230V - 50Hz Total wattage 6400W Instant heat effect Left front 12/18 cm Left Back 14 cm Right back 21 cm Right front 14 cm 700/1700 W 1200 W 2300 W 1200 W This unit is labelled to indicate conformity with the lowvoltage directive (73/23/EEC) and the EMC directive (89/336/EEC). Unpacking hobs the nameplate.
Service Before calling service – Technical advice Sympton Solution The hob is not working Check your earth leak circuit breaker. Check fuses. The hob becomes hot The ceramic hob will reach a temperature of 80˚C. It may, however, become even hotter if you use cooking utensils with uneven bases or which does not match the size of the cooking zone. The fuses keep blowing Too many electrical appliances may be in use at the same time.
Problems Solution Zones will not come on, Child safety device has been activated. Turn the 2 display shows control buttons with symbol for child safety device to simultaneously. Then activate one of the zones within 10 seconds. S A F E Zones will not come on, Autostop has been activated. Turn all the control display shows buttons to 0. The zones can now be used.
Deep fat frying For safety purposes, when deep fat frying, fill the pan 1/3 full of oil. Do not cover the pan with a lid and do not leave the pan unattended. In the event of a fire, switch off at the electricity supply and cover the pan with a lid or damp cloth to assist in smothering the flames. Do not use water on the fire. Leave the pan to cool for at least 30 minutes before moving it. 4. Cooking the food Lower the food gently into the oil.
It is better to use two pans rather than overfill one, or use half quantities. 3. What to use Use firm fruit or vegetables and wash well before using. 4. Types of sugar Preserving sugar gives clear jam, however granulated sugar is cheaper and gives equally good flavour. 5. Crystallization Crystallization may be caused if sugar is not completely dissolved before bringing the jam to the boil. Over boiling will affect the flavour, setting properties and colour of the jam. 6. To test jam for setting.
32 325 88-4370 Rev.
