25 D Extractor Hood Installation and Operating Instructions
Contents Introduction 3 Extraction mode Recirculation mode 3 4 Electrical connection for UK 5 Technical details 6 Installation 7 Safety warnings for kitchen unit installer Wall mounting 7 9 Hood operation 11 Safety warnings for user 12 Maintenance and care 13 Opening the grid Grease filter Carbon filter Changing the light bulb 13 13 14 15 Cleaning 15 Accessories 16 What to do if 17 Service & Spare Parts 18 Printed on recycled paper. AEG putting words into action.
Introduction Extraction mode ● The hood is supplied as an extractor unit and can also be used as a filtered function (recirculation) by fitting activated carbon filters (available as an accessory). ● The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.
● Move the lever L to position A Fig. 3. L L 3 ● When connecting the hood using a telescopic wall pipe, you should use a non-inflammable outlet hose ABS 120 (120 mm Ø) E-Nr. 942 118 611 from our range of special accessories. Recirculation mode ● The air is filtered and recirculated through the front grid. ● Move the lever L to position F Fig. 3. You will need an original KFF activated carbon filter. (See accessories).
Electrical connection for the UK Appliances with 2 wires WARNING: DOUBLE INSULATED - DO NOT EARTH The appliance must be connected to fixed wiring with a double pole switched fused spur outlet with or without pilot lamp. We strongly recommend the appliance to be connected only by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations.
Technical details Dimensions Height x Width x Depth (in cm) 69-113 x 59.
Installation Safety warnings for kitchen unit installer ● When used as an extractor unit, the hood must be fitted with a 100 or120mm diameter hose. ● If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.- 610 899 004 (Ø 120 mm) which is one of our optional parts.
● Regulations on fuel-burning systems specify a maximum depression of 0.04 bar in such rooms. ● Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm2 to avoid the possibility of a depression being created during operation of the hood. If you have any doubts, contact the relevant controlling authority or building inspectors office.
Wall mounting ● Fix the drilling template to the wall. ● Make 3 Ø 8mm holes in the wall 2 at points I, 1 as desired at points L. ● Insert the three Ø 8mm expansion plugs into the wall. ● Insert 2 5x45 screws at points I but do not tighten them completely. ● Adjust the unit so that it is positioned at a right angle to the wall by turning the two support screws G. ● Fit the hood into holes I, tighten the 2 screws. ● From inside the hood, insert the third 5x45 screw into hole L. Fig. 4.
● Set the chimney according to the measured height and stop its run with the two fixing screws 2,9x6,5 mm supplied (fig. 6). 6 7 ● Fix the chimney to the aesthetic top with two screws 2,9x6,5 mm supplied (fig. 7). ● From the inside of the hood, fix the aesthetic top with four screws M3x6 supplied (Two each side)(fig. 8). ● Fix the upper bracket to the wall, close to the ceiling, perpendicularly to the outlet hole of the hood with 2 screws 5x45 mm (fig. 8).
Fixing the shelf ● Fix the four plastic supports with the four screws provided to the height preferred. 9 Hood Operation ● The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
Safety warnings for user ● Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil or coal cooker flames in particular should never be left uncovered. ● Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames. ● The risk of a fat fire increases when using dirty oil. ● It is extremely important to note that overheating can cause a fire.
Maintenance and care ● The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grid ● Open the latch L and swing the grille downwards. Fig. 10. ● To remove the grid, pull it forwards from the right and release it. 10 Grease filter ● The purpose of the grease filteris to aspirate grease particles which form during cooking and it must always be used, either in the extraction or recirculate mode..
Removing the filter Open the grid and remove the stops M to take out the filter. See Fig. 6. Carbon filter ● The activated carbon filter should only be used if you want to use the hood in recirculation mode. ● To do this you will need an original AEG activated carbon filter (available as an accessory). ● This filter cannot be cleaned or reused. ● As a general rule, the activated carbon filter should be changed once every four months. ● Mounting Fig 11 a. Fit first rearwards on the proper seats. b.
Warning ● Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. Changing the light bulb ● Disconnect the unit from the mains power supply. ● Remove the grid. ● Replace the old light bulb with a new light bulb (40 W max.). ● If the light does not come on, make sure the bulb has been screwed in correctly before contacting AEG Service Force.
Special accessories MKZ telescopic wall pipe outlet hose ABS100 100 mm Ø outlet hose ABS120 120 mm Ø Metal grease filter MFF2 Carbon filter KFF 16 E-Nr.
What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively.. . Chec k that: The fan speed is set high enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air.
Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk Please ensure that you have read the section „What to do if....
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Copyright by AEG LI03ZB Ed.
