INSTRUCTION BOOK 115 DD-m 1 AUS/NZL GB 949600734
Congratulations from AEG Dear Customer, Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked . These are warning texts to help you avoid accidents. Keep the operating instructions.
Table of contents Content Page no. For the user Your new aplliance ....................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 5 The functions of the worktop extractor ................................................ 5 Pilot light ......................................
Safety information These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Maintenance and Cleaning This appliance can be a fire hazard if the grease filter is not cleaned regularly Under no circumstances should you attempt to repair the appliance yourself.
Description of the product The functions of the worktop extractor The air is sucked through the grease filter and then blown via the vent hose to the vent duct and out into the atmosphere. Top cabinet As opposed to an ordinary extractor, the worktop extractor is placed next to the cooker. The worktop extractor can be adjusted to two heights, the lower and upper positions. For each height there are two suction speeds to choose from.
Pilot light Control button The pilot light is located on the front of the product. The pilot light comes on when the product is switched on and extinguishes when the product is switched off. Pilot light The extraction capacity of the worktop extractor The extraction capacity is 370m³/h at the high extraction speed and 211m³/h at the low extraction speed. The extraction capacity of the worktop extractor is reduced with every bend of the vent hose/duct.
How to use the worktop extractor Never leave the worktop extractor unattended while deep fat frying or heating fats and oils. Do not flambé in immediate vicinity of an operating worktop extractor. Operation Adjust the height and extraction speeds of the worktop extractor as follows: Worktop extractor disconnected Worktop extractor in lower position.
Worktop extractor in upper position.
Use the worktop extractor correctly To have the worktop extractor working correctly, the kitchen windows should be kept closed to lower the pressure in the room. On the other hand to obtain maximum effect a window should be open in another room.
Cleaning and maintenance Before carrying out any maintenance or cleaning isolate the extractor from the mains supply. The extractor must be kept clean as build up of grease or fat can be a fire hazard The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface” Be aware of the two retaining pegs, which are sharp. 4.
Clean the appliance after use with a soft cloth well wrung out in warm water, use a small amount of liquid detergent for stubborn soiling. Stainless steel parts may become straw coloured with use, use a proprietary stainless steel cleaner to remove this straw discolouration. Never use metal wool, metal sponges or other abrasive cleaning agents.
To maintain optimum extraction capacity of the worktop extractor and to avoid fire hazards, the grease filter should be cleaned at least once a month. Proceed as follows: 1. Place the worktop extractor in the upper extraction position. 2. Lift off the top cabinet. The top cabinet can be washed in ordinary washing up liquid or in a dishwasher. 3. Lift off the black plastic tube – can be cleaned in the same way as the top cabinet. 4.
Fitting The worktop extractor can be fitted in any type of kitchen worktop with a thickness of between 28 and 40 mm. Location It is recommended that you install the worktop extractor in continuation of the hob. If two or more hobs are installed, the worktop extractor should be placed between the units so that you can take full advantage of the variable extraction direction.
Fitting reinforcement beams All 145 mm and 290 mm units come with a reinforcement beam. A reinforcement beam must be fitted between each unit. The beam should not be screwed onto the worktop, but be kept in place by the frame section of the units. 145 mm: Worktop extractor The capacity is also reduced in proportion to any increase in the length of the vent hose/duct. The less resistance the exhaust air meets, the better the extraction capacity and the less noise from the worktop extractor.
Installation This extractor unit must be installed according to the instructions supplied. Any electrical installation work must be undertaken by a qualified electrican/competent person. Do not alter the specifications or attempt to modify the appliance in any way. The ducting system for this appliance must not be connected any existing ventilation system which is being used for any other purpose. Connection to outlet Connection to a vent duct must be carried out in accordance with current regulations.
The connection must be completely tight regardless of the connection chosen. To install cable, remove front cover as shown. Connection Min. cable dimension: 0.75 mm² Cable type: HO5VV-F IMPORTANT Installation next to a gas unit To install the work top extractor next to a gas hob, proceed as follows: Disconnect the wires from settings 1, 2, 4, 5 (blue, green, yellow, orange) of the selector. Also disconnect green and orange wires from setting 1 of the micro switch. Do not reconnect these two wires.
Unpacking Serial number Check that the worktop extractor has no faults and is undamaged on delivery. You will find the serial number of the hobs on the rating plate, which is on the underside of the hob. We recommned you write this number on the cover of this instruction, so that you have this information to in the case of any service requirements. Transport damage Any damage from transport which you have not carried out yourself must be reported to the retailer within one week of receipt.
Service Before calling service – technical advice Symptom Remedy The worktop extractor is not working Check the worktop extractor plugged in and the electrical supply is swithced on. Check that the R.C.C.B. has not triped (if fitted) Check that main has no blown.
325 88-4740 Rev.
