Technical data

Accessories
Accessories
56|
Steca Elektronik GmbH | 87700 Memmingen | Germany | Fon [phone] | Fax [phone] | www.steca.com
|57
Accessories for Steca Xtender XTH
Steca RCC-02
Remote control and display
Lots of information on the status of the system can be re-
trieved using the graphic display of the Steca RCC-02. Any
incidents within the system are also saved and displayed. This
means that any problems which might occur are identified
early.
Many values of the Steca Xtender can be set using the Steca
RCC-02, such as the charging process of the battery charger,
the programming of the multifunctional contacts and the
various operating modes.
An SD-card slot can be used to save parameters, for transfer-
ring data or updating the software.
Displays
Multifunction graphical LCD display with backlighting
Operation
Programming by buttons
Certificates
Compliant with European Standards (CE)
RoHS compliant




Accessories for Steca Solarix PI
Steca PAx4
Parallel switch box
Up to four Steca Solarix PI can be operated in parallel. The
connections are made via an external box, the Steca PAx4.
A further innovation that has gone into the Steca Solarix PI is
the communication with the solar charge controllers from the
Steca Tarom and Power Tarom series. A data connection to
the charge controller can be created via the Steca PAx4.
RCC-02
Fitting and construction
Degree of protection IP 20
Dimensions (X x Y x Z) 170 x 170 x 46 mm
Weight 400 g
Technical data at 25 °C / 77 °F
PAx4
Operating conditions
Ambient temperature -20 °C … +45 °C
Relative humidity 0 % … 95 %
Fitting and construction
Cable data cable master: 0.5 m red
data cable slave 1: 0.5 m grey
data cable slave 2: 1m grey
data cable slave 3: 1m grey
data cable Steca Tarom: 3 m black
Interfaces 6 x RJ45
(4 x inverter, 2 x Steca Tarom)
Degree of protection IP 20
Dimensions (X x Y x Z) 206 x 117 x 64 mm
Weight 800 g
Technical data at 25 °C / 77 °F
Steca PA IRS 1008/180
Motion detector
The Steca PA IRS 1008/180 motion detector is connected to
the load output of the night light charge controller. This sup-
plies power to the light, which is then turned on for a few
minutes when some movement is detected.
The Steca PA IRS 1008/180 stands out, above all, with its ex-
tremely low own consumption, and is therefore optimal for
use in solar power systems.
[ar eas o f a pp lic at ion ]
[0 A ... 5 A]
PA IRS 1008/180
Characterisation of the operating performance
Own consumption 6 mA
Turn on time 1 min. ... 5 min.
DC output side
Battery voltage 12 V
Load current 5 A
Fitting and construction
Reach / detection area 7 m / 180°
Degree of protection IP 65
Technical data at 25 °C / 77 °F
[ar eas o f a pp lic at ion ]
Steca PA RC100
Remote control
Steca PA RC100 remote control allows to program Steca solar
charge controllers. The values can be adjusted with the help
of switches. After a restart of the charge controller the new
settings can be activated by pressing the program-button on
the Steca PA RC100. An LED will transfer the values to the
controller.
Product features
Low weight
Simple installation
Maintenance-free
Low own consumption
Best reliability





PA RC100
Characterisation of the operating performance
Supply voltage 4.5 V (3 * 1.5 V AAA / R03 batteries)
Adjustable parameters – Type of battery: gel / liquid
– Night-light function
– End of charge voltages (float / boost / equal)
– Deep discharge protection (LVD)
– LVD factor
– Switch-on threshold
Suitable for the following
Steca charge controllers
– Steca Solsum F
– Steca PRS
– Steca Solarix MPPT 2010
Fitting and construction
Dimensions (X x Y x Z) 115 x 57 x 20 mm
Weight 90 g
Technical data at 25 °C / 77 °F
[ar eas o f a pp lic at ion ]