Specifications

Peripherals
©2002 Bally Gaming and Systems 8-19 Peripherals
Bill Acceptors (cont.)
• Apply power, then turn DIP switch 6 to OFF. The unit
should cycle.
• The unit is ready for stand-alone testing.
• Insert a bill/note. The bill/note will either be accepted
and go complete through the bill head, or be rejected.
• If the unit rejects the bill/note, refer to the Bill Return
Codes table.
• If the unit will not take the bill/note, check the Abnor-
mal Initialization Codes table.
• When the unit cycles on power ON. this indicates
power and forward motor operation.
• When a plain piece of paper is inserted and rejected
this indicates reverse motor operation.
• When various denominations of currency are inserted
and accepted, this indicates the bill/note was accu-
rately match against the characteristics of the soft-
ware version.
Bill Return Codes
sknilBfo# noitpircseD esuaCelbissoP
1
noitresnidekoorC
dekoorcdetresnisawlliB
noitcnuflamrosnesecnartnE
22
2
22
rorrenrettapcitengaM
nrettapcitengamgnitcetedrorrE
eton/llibano
33
3
33
nielihwllibadetcetedrotpeccA
ybdnats
afoecneserpehtdetceteD
ydnatsnielihweton/llib
4
ehtwolebsioitarthgil-kraD
eulavdexif
ebtonyamsrosnesevitcelfeR
ylreporpgnikrow
55
5
55
rorredeeftropsnarT
ehtybdetcetedtoneton/lliB
anihtiwrosnesdeeftropsnart
doirepdeificeps
77
7
77
rorrenrettapotohP
tonnrettapaevahyameton/lliB
nidezingocerrodemmargorp
yromem
gnikrowebtonyamrosneS
ylreporp
88
8
88
rorrelevelotohP
srellorro/dnastlebytriD
detcetedllibgnippalrevo/elbuoD
ytridebyameton/llibehT
99
9
99
sgnittestibihniybnruteR
egnarotnillaftonseodeton/lliB
ro,seton/sllibelbatpeccafo
noitceridnoitanimoned
0101
01
0101
tsohybdenruteR
tonlliwsgnittes/margorpemaG
eton/llibdetresnidetpecca
2121
21
2121
llibaelihwllibrehtonadetceteD
edomkcatsnillitssaw
noitcnuflamrosnesecnartnE
rosnesecnartnegnikcolbtcejbO
3131
31
3131
rorrehtgnellliB
nihtiwtoneton/llibfohtgneL
noitacificepsdemmargorp
4141
41
4141
rorrenrettaproloCsgnikram/edahs/rolocralugerrI
5151
51
5151
snosaerrehtoybdenruteR
)rorrecitengaM(
htiwrorrenoitanibmocA
srosnescitengam
NO1SD
FFO123456789 01
ESUECAFRETNI/NOITANIMONED
NO2SD
FFO123456
ESUCITSONGAID
NOTE: Calibration paper may be
purchased from JCM American directly
by calling the Parts Sales department at
[phone] and requesting part
number #057619.
sknilBfo# noitpircseD esuaCelbissoP
1
lluFxobhsaC
LLUFebyamxobhsaC
gninoitcnuftonrotoM
gnikrowtonrosneS
tilpsrodekcarcraegredocnE
2
xobhsaCnimaJ
ebyammsinahcemrehsuP
demmaj
tonrosnesredocnerekcatS
gninoitcnuf
33
3
33
tinUtropsnarTnimaJ
neporevoC
melborprevelrekcatS
htapgniyrracehtnisniamerlliB
44
4
44
daeHrotpeccAnimaJ
srosnesgnikcolbtcejbonA
melborprosneS
55
5
55
rorrEdeepSrotoM
s'rotpeccaehtmorflangisoN
rosnesredocne
66
6
66
rorrEpotSrotoM
gninoitcnuftonrotoM
tilpsrodekcarcraegredocnE
gninoitcnuftonrosnesredocnE
88
8
88
rorrEdioneloS
gninoitcnuftondioneloS
emohtatonrevelrekcatS
noitisop
0101
01
0101
devomeRxobhsaC
)ylnostinuSS(xobhsacoN
ylreporpdetaestonxobhsaC
2121
21
2121
detceteDnoitidnoCtaehC
elbissopetacidnisrosneS
noitalupinamrosnes
5151
51
5151
rorrEtnemtsujdAA/D
r
orrerosnesnoitarbilacelbissoP
Abnormal Initialization Codes
Auto-Calibration
1. Power
OFF
2. Set DIP switch DS2: 4, 5, and 6 to ON.
3. Power-on the unit plugging in the 6-pin connector.
4. Head motor will cycle and stop indicating it is ready
to calibrate.
5. Insert the DBV-200 calibration paper, black side first.