Test Report No.
LCD Monitor User's Guide Models IL-1900B LPP
INTRODUCTION FCC Compliance Statement .......................................................................................................... i Safety Instructions ................................................................................................................................... iii General Information ............................................................................................................................... 1 Equipment Check list ......................................
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against radio frequency interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.
INTRODUCTION FCC COMPLIANCE STATEMENT DCC COMPLIANCE NOTICE: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
INTRODUCTION SAFETY INSTRUCTIONS o Handling Due to its fragile glass panel, this monitor must be handled with caution and not be exposed to impact or shock. Never touch the display area or rub it with a hard object or tool, as the panel is easily scratched. o Cleaning The display area is sensitive to scratching. Do not use ketone-type cleaners (i.e. acetone), ethyl alcohol, toluene, ethyl acid or methyl chloride to clean the panel. Doing so may result in permanent damage.
INTRODUCTION SAFETY INSTRUCTIONS o Caution 1. Do not open any covers on the monitor. No user serviceable parts are inside. 2. In an emergency, disconnect the AC power plug. 3. To avoid electrical shock, disconnect the power cord from the monitor before connecting the signal cable to the computer. 4. Keep away from liquids and flame. Do not immerse this monitor in water or any other liquid. Do not use this device in excessively hot conditions. 5. Handle the power cord with care.
Your new LCD monitor incorporates the latest state-of the art color Liquid Crystal Display (LCD) technology providing a wider viewing angle with higher contrast ratio. Your new LCD monitor has many advantages : safe from electromagnetic wave, lights, sharps and slims. This makes the monitor extremely suitable in the environment of administration, transportation system research, etc. Your new LCD monitor is designed for Analog and DVI input.
INTRODUCTION EQUIPMENT CHECK LIST Before operating your display, please check to make sure that all of the items listed are present in your package: v Accessory Box 1) AC to DC Adapter 2) Power Cord 3) Signal Cable(D-SUB) 4) Signal Cable(DVI-D) 5) USB Cable 6) Audio In Cable 7) Manual v Power Requirements The monitor is equipped with an auto-sensing power supply for voltage ranging from 100-120VAC/200-240VAC, 50/60Hz.
INTRODUCTION MONITOR FEATURES * Supports Analog and Digital(DVI-D) IBM compatible PC, Apple MacintoshTM (Adapter optional) * Supports DPMS for monitor power management * Support DDC2B * On Screen Control : Auto-Tune, Contrast, Brightness, H/V Position, H-Size, Phase, Auto-Level, Color Control, Sharpness, Input Select, TEXT/MOVIE, Volume, OSD Position, OSD Time-out, Power Save Delay, Language, Information.
INSTALLATION GETTING STARTED v Follow these steps to install the monitor 1. Before you connect the cables, make sure the monitor and system unit power switches are OFF. 2. Plug the 15-pin signal cable or 24-pin DVI Cable between the rear of your Monitor and system. The adapter may be required for certain Apple Macintosh computers. Tighten the two screws on the cable connector. 3. Plug the Audio Cable between Audio input Jack in the rear of your monitor and audio output of your system. 4.
CONTROL BUTTONS OSD Buttons : The OSD control keys are located on lower left of the GETTING STARTED monitor. (Enter) a. No OSD : This button will enable the main OSD menu. b. Main OSD menu : Press this button to enter to the selected OSD control menu. c. Cotrol OSD menu : Swap the control item. or (Up/Down) : Use these buttons to increase or decrease each value. a. No OSD : : Audio volume control menu will be shown. : Contrast & Brightness control menu will be shown.
CONTROL BUTTONS GETTING STARTED Button Description : 1. 2. 3. 4. 5. 6 : Display On Screen Control menu. Access the control menu. : Move selected icon up to select one of the controls. Increase the control value. : Move selected icon down to select one of the controls. Decrease the control value. : Exits the On Screen Control. Do Auto Tune function. (Press and hold this button for two seconds.) : Select the Display mode. Switch D-SUB(Analog) to DVI(Digital).
ON-SCREEN DISPLAY Before activating the OSD menu, the button can be used to automatically adjust the display to the proper size and horizontal and vertical position. (Press button for 2 seconds.) The OSD menu activates automatically when you press the Enter button on the lower left of the monitor. The OSD remains centered on the screen while you make your adjustments. Use either the or button to move the highlight to your selection. submenu or control with a status bar will appear.
ON-SCREEN CONTROLS MENU DESCRIPTIONS Main Menu AUTO-TUNE This control will automatically make adjustments to the horizontal and vertical size, horizontal and vertical position, phase and color. CONTRAST This control allows you to make adjustments to the contrast of the display screen. BRIGHTNESS Selecting this control menu allows you to make adjustments to the luminosity level of the display screen.
MENU DESCRIPTIONS PHASE Select this control menu, and then use the and buttons to adjust the screen image until it looks focused, crisp and sharp. AUTO-LEVEL This control will automatically make adjustment to the input levels of video signal.(ex. 0.714Vp-p, 1.0Vp-p) Select this control menu, then use the and buttons to scroll to the desired color temperature. Use the button to select the 9300K, 6500K, 5500K, or USER for custom setting.
MENU DESCRIPTIONS TEXT/MOVIE ON-SCREEN CONTROLS Select this control menu, and then use the and buttons to select proper image either text mode or movie mode. Default setting is Text mode. This function can be used by hot key on the front of monitor. (See clause 6.2.3.) VOLUME Select this control menu, and then use the and buttons to increase or decrease audio sound level. This function can be used by hot key on the front of monitor. (See clause 6.2.
POWER MANAGEMENT LED INDICATOR (POWER MANAGEMENT ACTIVE) The power management feature is comprised of two stages : On or Out Of Range (Green), Off (Green blinking). In the off mode, all circuitry in the monitor is shut down, except for a low power detection circuit. This circuit allows the monitor to wake up when the mouse is moved or a key on the keyboard is pressed.
TIMING GUIDE The LCD is a multi-frequency display. It operates at horizontal frequencies between 30KHz ~ 80KHz and vertical frequencies between 55Hz ~ 75Hz. Because of its microprocessor-based design, it offers autosynchronization and auto-sizing capabilities. This monitor offers 10 preprogrammed settings that are listed in the timing table on page 11. REFERENCE These preset modes cover most of the common video modes supported by popular graphics adapters.
PIN ASSIGNMENT VGA Connector(Cable Side) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue No Connection Ground Red Ground Green Ground Blue Ground No Connection Ground Ground DDC SDA Horizontal Sync. Vertical Sync. DDC SCL POWER JACK(Monitor Side) 1 2 REFERENCE Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin VGA CONNECTOR Ground DC+12V input DVI Connector(Cable Side) DVI-D Connector (TMDS Single Link) Pin Signal Pin Pin Signal Signal 1 T.M.D.S. Data29 T.M.D.S. Data117 T.M.D.S.
SPECIFICATIONS LCD REFERENCE Viewing Angles Type 19” diagonal viewable screen TFT (Thin Film Transistor), Active Matrix Panel, 0.098 x 0.294mm pixel pitch Color Filter R,G,B vertical stripe Colors 16.7M Glass surface Anti-glare coating Left / Right Up / Down 85° / 85° 85° / 85° Contrast Ratio Typ. 400:1 Luminance of White Typ. 250cd/m2 Compatibility PC IBM XT, AT, 386, 486, Pentium or PS/2 and compatibles(from VGA and DVI up to 1024 x 768 @ 75Hz NI.) Refresh Rate Max.
TROUBLESHOOTING v No power. ( Flip the power switch ON. The Power LED turns on. ( Make sure AC power cord is securely connected to a power outlet. v Power on but no screen image. ( Make sure the video cable attached with this monitor is tightly secured to the video output port on the back of the computer. ( Adjust the brightness and contrast. v Image is unstable, unfocused. ( Use “AUTO-TUNE” to adjust automatically.
TROUBLESHOOTING ( Connect the LCD Monitor to another computer. ( Check the graphics card for proper sync scheme (or sync polarities) to match the LCD Monitor’s specifications. v Double (split) screen image. ( Make sure your graphics card is set to Non-Interlaced mode. v Entire screen image rolls (scrolls) vertically. ( Make sure the input signals are within the LCD monitor’s specified frequency range. (Maximum: VESA, MAC 1280 x 1024@75Hz) REFERENCE ( Connect the video cable securely.
MEMO 17
MEMO 18
