ADVDLX10 10.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Important Notice Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants.
FEATURES Congratulations • 10.1” TFT (Thin Film Transistor) Active Matrix LCD (Liquid Crystal Display) Monitor Congratulations on your purchase of the ADVENT ADVDLX10 DVD Player with drop-down video / monitor. The ADVDLX10 has been designed to give you and your family many years of video entertainment in the mobile environment. Please read the directions that follow to familiarize yourself with the product to ensure that you obtain the best results from your equipment.
CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW) 4. P LAY (u) Button This button is used to start playback of a disc. 1 2 5. STOP (n) Button -Press the STOP button once: Stops playback. - Pressing the PLAY button again will resume normal playback from where movie was stopped. - Press the STOP button twice and then press the PLAY button to start playback from the beginning of the DVD. 3 4 5 6 7 8 6. EJECT ( ) Button This button is used for ejecting disc from the disc compartment. 9 10 7.
CONTROLS AND INDICATORS DIAGRAM SIDE VIEWS Note: Use 2-channel IR headphones set to CH B when the monitor is set to M2 mode. Note: M1 will appear on the screen for 4~5 seconds. 1 Selecting a Monitor Code (M1 or M2) 2 1. P ower ON the unit and wait until M1 on the OSD appears. M1 will appear on the screen for 4~5 seconds. 3 FMM 88.3MHz AUX/GAME FMM OFF DVD M1 1. 2. DVD Disc Insertion Slot For loading and removing discs. Insert disc with label side facing up. IRT ON IRT OFF 2.
REMOTE CONTROL FUNCTIONS REMOTE CONTROL OPERATION Initial Use When purchased, the remote control has a battery installed with a Pull Tab to prevent battery discharge. Remove the Pull Tab before attempting to use the remote control. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CR2025 15 Battery Replacement 1. Remove the battery holder. 2. Insert one CR2025 battery into the battery holder. Be sure to observe the correct polarity. 3. Align the battery holder with the remote control and insert.
* Function control is available on the unit and the Remote Control. ** Function not available in this model. 1. POWER* Press this button to turn the unit ON and OFF. 2. SOURCE* Each time the button is pressed, the unit will cycle through modes DVD/USB, AV, AUX. 3. MONITOR SELECT M1 Button – Set the remote control code to allow control of the unit in M1 mode. M2 Button – Set the remote control code to allow control of the unit in M2 mode. 4. SCAN BACKWARD ( ) Press to search in a backward direction.
10. SYSTEM MENU Allows the user to access the system menu when the unit has been placed in TV mode. Press the cursor buttons (pq) to select FM MODULATOR, OSD LANGUAGE, DEFAULT DVD ON/OFF, SCREEN MODE, MONITOR MODE. Note: Press once to access the System Menu, press twice to exit the System Menu. 11. CURSOR (pqt u) Use these buttons to access menu selections on the screen. 12. DISPLAY Press to display the current disc information while the disc is playing.
18. NUMBERS Allows the user to enter the numbers 0-9 for selection of the tracks, titles, chapters or password setting. 19. ZOOM Press this button to enlarge the picture when playing a DVD disc. Press ZOOM button DVD player Once Q1- Enlarges the picture twice the original size Twice Q2- Enlarges the picture 3 times the original size 3 times Q3- Enlarges the picture 4 times the original size 4 times Q off- Picture is returned to original size 20.
24. PIX ( Picture Select ) Each time this button is pressed, the OSD picture adjustment displays the “Adjustment Bar” for BRIGHTNESS, CONTRAST, COLOR, TINT (For NTSC only) or RESET. Once the desired adjustment bar is displayed, use the VOLUME +/ VOLUME – buttons to adjust the setting. The display will automatically turn off if no adjustments are made within 6 seconds. 25.
TURNING THE UNIT ON OR OFF 1. Push in the Screen Release button to unlock the LCD screen. The screen will drop down slightly. 2. Pivot the screen downward until a comfortable viewing angle is reached. The hinge friction will hold the screen in position while the system is in use. 3. ress the power button on the unit or the remote control to turn the system on and off. When in use, the internal backlighting will illuminate the P controls. 4.
PICTURE CONTROL SELECT When watching a program, the picture quality can be adjusted to the user’s preferences. 1. P ress the Picture (PIX) button on the remote control and the on screen picture adjustment displays the “adjustment bar” for BRIGHTNESS, CONTRAST, COLOR, TINT (for NTSC only) or RESET. 2. Use the Volume buttons + or - to adjust the selected adjustment bar for picture quality.
FM MODULATOR The FM Modulator allows the user to listen to audio through the vehicle’s radio. ON - Turns the wireless FM Modulator on if audio playback through your vehicle’s radio is preferred. OFF - Turns the wireless FM Modulator off. FM CHANNEL - Allows the user to select the wireless FM Modulator frequency. The unit has a 100 channel built-in wireless FM Modulator. The FM Modulator can be set from 88.1 to 107.9 in 0.2 MHz steps, i.e. 88.1, 88.3, 88.5, 88.9, 90.1 etc.
OSD LANGUAGE This function allows the user to select the on-screen display language. The user can select English, Spanish, French or German for the OSD language. 1. Press the System Menu button. 2. Use the p or q cursor buttons to highlight OSD LANGUAGE and press OK to access the OSD submenu. 3. Use the p or q cursor buttons to select the language. 4. Press the OK to confirm the setting. SOURCE DEFAULT DVD ON/OFF This allows the user to set the system default source to DVD.
MONITOR MODE This allows the user to set the system monitor code M1/M2. 1. Press the System Menu button. 2. Use the p or q cursor buttons to highlight MONITOR MODE and press OK to access the monitor mode submenu. 3. Use the p or q cursor buttons to select M1 or M2. 4. Press the M2 button on the remote control after selecting M2. 5. Press OK to confirm the setting. WARNING SYSTEM MENU SETTING THE MONITOR TO THE M2 MODE WILL REQUIRE USING 2-CHANNEL HEADPHONES.
DVD SUBTITLE SETUP The Subtitle Menu allows the user to select the language for the on-screen display subtitles. 1. Press the SETUP button on the remote to enter the Setup Menu. 2. Use the p or q cursor buttons to select the Language menu option. 3. Use the u cursor button to select subtitle submenu. 4. Use the q cursor button to select the subtitle option. 5. Use the u cursor button to select subtitle submenu. 6.
Misc Chinese Japanese DVD TV DISPLAY The TV display setup allows the user to set the screen aspect ratio. 4:3 - This displays the wide picture with black bands on the upper and lower portions of the screen. 16:9 - This displays a wide picture with black bands on the upper and lower portion of the screen. The bandwidth will vary, depending on the aspect ratio of the disc. 1. 2. 3. 4. 5. Press the SETUP button on the remote to enter the Setup Menu.
DVD RATING SETUP Parental This feature allows the user to limit the content of movie playback from G to Adult. The lower the value, the more strict the control. 1. G 2. PG 3. PG – 13 4. R 5. NC – 17 6. Adult The rating level can only be changed when the correct password is provided. To change the parental control level, perform the following: 1. Press the SETUP button on the remote to enter the Setup Menu. 2. Use the p or q cursor buttons to select the Rating menu option. 3.
Load Factory This option allows the user to reset all options to factory settings. 1. Press the SETUP button on the remote to enter the Setup Menu. 2. Use the p or q cursor buttons to select the Misc menu option. 3. Use the u cursor button to select the load factory option, then press OK to enter the submenu. 4. Use the t or u cursor buttons to select the load factory Yes or No, then press OK to confirm the setting. 5. Press the SETUP button on the remote to exit the Setup Menu.
PLAYING DVDS 1. Press the DISPLAY button on the remote control to display the status banner. The banner includes title, chapter, angle, audio, subtitle, and time. 2. Title Selection Press the numeric (0~9) buttons to initiate a change of title selection. Then press OK to implement the selection. 3. Chapter Selection Press the numeric (0~9) buttons to initiate a change of chapter selection. Then press OK to implement the selection. PLAYING MP3 DISCS MP3 is a format for storing digital audio.
Repeat: play repetitively The Repeat function has four playing options: Off, Single, Folder, and All. Move the cursor to the Repeat function and press OK. Each time OK is pressed the unit will cycle through the available options. Off/Single/Folder/All are displayed in that order. The Repeat default is Off. Off Single Folder All 00:00:01 / 1/12 Flat Mode 001 Repeat : Off 002 Mode 003 : Normal 004 - Turns the repeat function off. - Repeats the song being played until STOP is pressed.
DVD Basics To get the optimum use out of the DVD Player, make sure this section is read completely. DVD Region Code The DVD player is preset to a region code at the factory depending on where the DVD player is sold. A DVD from a different region cannot be played in this unit and the unit will display "WRONG REGION”. Region 1 - USA, Canada Region 2 - Japan, Europe, South Africa, Middle East, Greenland Region 3 - S.
Types of Discs the DVD System will play The ADVDLX10 DVD system will play the following types of discs: • DVD* disc - DVD discs which contain video. • Audio disc - Audio CDs contain musical or sound content only. • MP3 disc - A disc that contains audio files (for example, a CD-R with downloaded MP3 files). • JPEG disc - A disc that contains JPEG files. *Note: T his system is capable of playing most recordable DVD formats.
OVERHEAD DOME LIGHTS The Dome Lights integrated into the unit are controlled by a three position slide switch. Sliding the switch to the ON position will turn the lights ON. The OFF position will prevent the lights from turning ON with the vehicle's interior lighting. The AUTO position will allow the lights to turn ON and OFF with the vehicle's interior lighting. Refer to the Installation Guide for wire connections.
TROUBLESHOOTING Problem Solution IR remote is inoperative. • Verify that the batteries in the remote are fresh. • Verify that the remote sensor eye is not obstructed. • If the monitor is set to M1, press the M1 button on the remote control. If the monitor is set to M2, press the M2 button on the remote control. (See page 5.) Disc won't play. • Insert a disc with the label side facing upwards. • Check the type of disc you put into disc tray. This DVD only plays DVD, audio CD and MP3.
Problem Solution Picture is distorted. • The disc might be damaged, try another disc. • It is normal for some distortion to appear during forward or reverse scan. No forward or reverse scan. • Some discs have sections that prohibit rapid scanning or title and chapter skip. • If you try to skip through the warning information and credits at the beginning of a movie, you won’t be able to. This part of the movie is often programmed to prohibit skipping through it.
REPLACEMENT PARTS SPECIFICATIONS Remote Control 136-5326 AV Adapter Pigtail 112B3227 LCD Backlighting LED Resolution 1024 (RGB) x 600 Pixels 1,843,200 Operation Temperature 32 ~131º F (0 ~ 55º C) Storage Temperature -4 ~ 158º F (-20 ~ 70º C) Back Light Life 20,000 Hours Video Display System NTSC / PAL Video Output 1.0 Vp-p @ 75 ohms Power Source 12 VDC Dimensions LxWxH 11.0" x 9.5" x 1.7" Closed 289mm x 243mm x 44mm Closed 11.0" x 9.
LIMITED WARRANTY R Applies to ADVENT Mobile Video Products VOXX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that, should this product or any part thereof (except game controllers), under normal use and conditions, be proven defective in material or workmanship within 36 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor.
NOTES 29
© 2014 VOXX ELECTRONICS CORP., 150 Marcus Blvd.
