Owner`s manual

ManualsBrandsAdvent ManualsComputer equipmentOVERHEAD LED BACKLIT LCD MONITOR

ADVEXL10

10.1" OVERHEAD LED BACKLIT

LCD MONITOR WITH

DVD PLAYER

OWNER'S

MANUAL

PUSH

Summary of content (36 pages)

PAGE 1
ADVEXL10 10.
PAGE 2
TABLE OF CONTENTS FCC Statement ........................................................................................3 Important Notice .................................................................................. 4 Warnings .................................................................................................. 4 Congratulations .................................................................................... 5 Safety Precaution .........................................................
PAGE 3
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 4
Important Notice Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants.
PAGE 5
FEATURES Congratulations • 10.1” TFT (Thin Film Transistor) Active Matrix LCD (Liquid Crystal Display) Monitor Congratulations on your purchase of the ADVENT ADVEXL10 DVD Player with drop-down video / monitor. The ADVEXL10 has been designed to give you and your family many years of video entertainment in the mobile environment. Please read the directions that follow to familiarize yourself with the product to ensure that you obtain the best results from your equipment.
PAGE 6
CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW) 1 8 9 4. H OME/MENU Select Button This button is used to display and select options on the system menu. Press and hold for 3 seconds to access the System Menu. 2 34 5 6 7 S 5. S ource/Select (S) Button Press this button to display the Source OSD screen. Use the cursor buttons to highlight the desired source. Press the Source/Select button to access the desired source. 8 PUSH 10 11 6. STOP (n) Button -Press the STOP button once: Stops playback.
PAGE 7
CONTROLS AND INDICATORS DIAGRAM (SIDE VIEWS) 1 2 3 4 5 1. D VD Disc Insertion Slot For loading and removing discs. When a disc is inserted, the unit will automatically turn ON and switch to DVD source. Insert a disc with label side facing up. Note: The disc slot indicator is red when a disc is inserted and green when the disc slot is empty. 2. AUX IN These jacks are used to supply external audio and video inputs to the unit. (Yellow - Video, White - Left Audio, Red - Right Audio). 3.
PAGE 8
REMOTE CONTROL FUNCTIONS REMOTE CONTROL OPERATION Initial Use When purchased, the remote control has a battery installed with a Pull Tab to prevent battery discharge. Remove the Pull Tab before attempting to use the remote control. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CR2025 15 Battery Replacement 1. Remove the battery holder. 2. Insert one CR2025 battery into the battery holder. Be sure to observe the correct polarity. 3. Align the battery holder with the remote control and insert.
PAGE 9
* Function control is available on the unit and the Remote Control. ** Function not available in this model. 1. POWER* Press this button to turn the unit ON and OFF. 2. SOURCE* Press to display the Source OSD for DVD, USB, HDMI 1, HDMI 2, Media, AV, AUX, DTV and Game. 3. MONITOR SELECT M1 Button – Set the remote control code to allow control of the unit in M1 mode. M2 Button – Set the remote control code to allow control of the unit in M2 mode. 4.
PAGE 10
. SYSTEM MENU Allows the user to access the system menu. Press the t or u cursor buttons to select PICTURE, WFMM (FM Modulator) and SETTING. 11. CURSOR (pqt u) Use the cursor buttons to access menu selections on the screen. 12. DISPLAY When in DVD mode, press to display the current disc information while the disc is playing. Use the t or u cursor buttons to select the Title or Chapter. For Title/Chapter selection use the numeric buttons to enter the desired Title /Chapter selection.
PAGE 11
18. NUMBERS Allows the user to enter the numbers 0-9 for selection of the tracks, titles, chapters or password setting. 19. ZOOM Press this button to enlarge the picture when playing a DVD disc. Press ZOOM button DVD player Once Q1- Enlarges the picture twice the original size Twice Q2- Enlarges the picture 3 times the original size 3 times Q3- Enlarges the picture 4 times the original size 4 times Q off- Picture is returned to original size 20.
PAGE 12
24. P IX ( Picture Select )** No function on this model. 25. VOLUME DOWN (-) or UP (+)** No function on this model. 26. MUTE Press this button to mute the audio for the wireless FM Modulator, IR headphones and audio output. Pressing the button again restores the audio to the previously set level. 27. DISC MENU Allows the user to access the disc’s menu mode. 28. STOP (n)* Press to stop playback. (Playback will resume from the point it is stopped). Press twice to stop playback fully.
PAGE 13
TURNING THE UNIT ON OR OFF 1. Push in the Screen Release button to unlock the LCD screen. The screen will drop down slightly. 2. Pivot the screen downward until a comfortable viewing angle is reached. The hinge friction will hold the screen in position while the system is in use. 3. ress the power button on the unit or the remote control to turn the system on and off. When in use, the internal backlighting will illuminate the P controls. 4.
PAGE 14
SOURCE MENU The ADVEXL10 System is capable of accessing nine source inputs. To select or change a source, press the source, S, button on the front panel or the SRC button on the remote control. The source OSD will appear on the screen as shown in the figure below. Use the p q t or u cursor buttons on the front panel or the p q t or u cursor buttons on the remote control to highlight a source. Press the Source, S, button on the front panel or the OK button on the remote control to select the desired source.
PAGE 15
MEDIA The Media source allows for the user to connect an Apple device (e.g. iPod, iPhone, iPad) to the ADVEXL10 System to play audio and video content. A special Apple adapter is required for this connection. See your Apple or electronics dealer for the specific adapter required. Connect the adapter to the Apple device, and connect the Audio, Video, and USB connectors into the ADVEXL10 System. With the Media source selected, the desired video and audio content can be displayed on the ADVEXL10 System.
PAGE 16
SYSTEM MENU SETTINGS AND ADJUSTMENTS The System Menu contains features and options that let the user customize the system. For example, the user can change the Picture, FM Modulator, OSD language, source default, screen mode display, and the monitor mode. Using the System Menu 1. Press the SYSTEM MENU button on the remote control. The system menu main page will appear on the screen. 2. Use the p q t or u cursor buttons to select an item in the sub menu, then press OK to select. 3.
PAGE 17
WFMM (FM MODULATOR) The FM Modulator allows the user to listen to audio through the vehicle’s radio. ON - Turns the wireless FM Modulator on if audio playback through your vehicle’s radio is preferred. OFF - Turns the wireless FM Modulator off. FREQUENCY - Allows the user to select the wireless FM Modulator frequency. The unit has a 100 channel built-in wireless FM Modulator. The FM Modulator can be set from 88.1 MHz to 107.9 MHz in 0.2 MHz steps, i.e. 88.1, 88.3, 88.5, 88.9, 90.1 etc.
PAGE 18
SETTINGS DEFAULT DVD This allows the user to set the system default source to DVD on or off. If source default is set to ON, every time the unit is turned off then on, the unit will power up and automatically switch the source to DVD. If source default is set to OFF and the unit is turned off then on, the unit will power up in the source that was last selected. 1. Press the System Menu button. 2. Use the u cursor button to highlight SETTING. 3. Use the q cursor buttons to highlight DEFAULT DVD. 4.
PAGE 19
MONITOR MODE MONITOR MODE SETTINGS The ADVEXL10 System has an option that allows the user to select from two IR transmit and receive codes (M1 or M2). This feature can be used when using two ADVEXL10 systems in the same installation or if the vehicle has RSA (Rear Seat Audio) that uses an “A” channel headset. The ADVEXL10 system comes factory set to M1. When in the M1 mode, the unit will respond to remote commands when M1 is selected on the remote control and will transmit audio on the A channel.
PAGE 20
IR TRANSMITTER This allows the user to turn the IR Transmitter ON or OFF. The IR Transmitter must be set to ON for the wireless headphones to be operational. 1. Press the System Menu button. 2. Use the u cursor button to highlight SETTING. 3. Use the q cursor button to highlight IR TRANSMITTER. 4. Use the t or u cursor buttons to select ON or OFF. 5. Press OK to confirm the setting.
PAGE 21
DVD SETUP MENU SETTINGS AND ADJUSTMENTS The DVD Setup Menu contains features and options that allow the user customize the DVD player. For example, the user can set a language for the onscreen display or prevent children from viewing DVD playback of adult DVD Titles. Using the Setup Menu Press the DVD button and then the SETUP button on the remote control. The Setup Menu appears on the screen as shown. 1. Use the p or q cursor buttons to highlight the settings to be changed.
PAGE 22
DVD SUBTITLE SETUP The Subtitle Menu allows the user to select the language for the on-screen display subtitles. 1. Press the SETUP button on the remote to enter the Setup Menu. 2. Use the p or q cursor buttons to select the Language menu option. 3. Use the u cursor button to select subtitle submenu. 4. Use the q cursor button to select the subtitle option. 5. Use the u cursor button to select subtitle submenu. 6.
PAGE 23
Misc Chinese Japanese DVD TV DISPLAY The TV display setup allows the user to set the screen aspect ratio. 4:3 - This displays the wide picture with black bands on the upper and lower portions of the screen. 16:9 - This displays a wide picture with black bands on the upper and lower portion of the screen. The bandwidth will vary, depending on the aspect ratio of the disc. 1. 2. 3. 4. 5. Press the SETUP button on the remote to enter the Setup Menu.
PAGE 24
DVD RATING SETUP Parental This feature allows the user to limit the content of movie playback from G to Adult. The lower the value, the more strict the control. 1. G 2. PG 3. PG – 13 4. R 5. NC – 17 6. Adult Language Video Parental : 6.Adult Change Password Rating Misc The rating level can only be changed when the correct password is provided. To change the parental control level, perform the following: 1. Press the SETUP button on the remote to enter the Setup Menu. 2.
PAGE 25
Load Factory This option allows the user to reset all options to factory settings. 1. Press the SETUP button on the remote to enter the Setup Menu. 2. Use the p or q cursor buttons to select the Misc menu option. 3. Use the u cursor button to select the load factory option, then press OK to enter the submenu. 4. Use the t or u cursor buttons to select the load factory Yes or No, then press OK to confirm the setting. 5. Press the SETUP button on the remote to exit the Setup Menu.
PAGE 26
PLAYING DVDs 1. P ress the DVD button and then the DISPLAY button on the remote control to display the status banner. The banner includes title, chapter, angle, audio, subtitle, and time. 2. Title Selection Press the numeric (0~9) buttons to initiate a change of title selection. Then press OK to implement the selection. 3. Chapter Selection Press the numeric (0~9) buttons to initiate a change of chapter selection. Then press OK to implement the selection.
PAGE 27
Repeat: play repetitively The Repeat function has four playing options: Off, Single, Folder, and All. Move the cursor to the Repeat function and press OK. Each time OK is pressed the unit will cycle through the available options. Off/Single/Folder/All are displayed in that order. The Repeat default is Off. Off Single Folder All 00:00:01 / 1/12 Flat Mode 001 Repeat : Off 002 Mode 003 : Normal 004 - Turns the repeat function off. - Repeats the song being played until STOP is pressed.
PAGE 28
DVD BASICS To get the optimum use out of the DVD Player, make sure this section is read completely. DVD Region Code The DVD player is preset to a region code at the factory depending on where the DVD player is sold. A DVD from a different region cannot be played in this unit and the unit will display "WRONG REGION”. Region 1 - USA, Canada Region 2 - Japan, Europe, South Africa, Middle East, Greenland Region 3 - S.
PAGE 29
Types of Discs the DVD System will play The ADVEXL10 DVD system will play the following types of discs: • DVD* disc - DVD discs which contain MPEG2 video. • Audio disc - Audio CDs contain musical or sound content only. • MP3 disc - A disc that contains audio files (for example, a CD-R with downloaded MP3 files). • JPEG disc - A disc that contains JPEG files. *Note: T his system is capable of playing most recordable DVD formats.
PAGE 30
ACCESSORIES WIRELESS HEADPHONES The ADVEXL10 includes a built-in infrared transmitter for use with the supplied wireless headphones. The headphone volume is adjusted using the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the transmitter, as infrared transmissions, like visible light, travel only in a straight line.
PAGE 31
HDMI/MHL AND USB PORT INFORMATION MHL devices **: Roku MHL streaming stick: http://www.roku.com/roku-ready/models * HDMI1 (HDMI/MHL Input located on the side of the unit) This input can be used for devices with HDMI or MHL output ports (such as smartphones, tablets, HDMI/MHL devices) and may require the purchase of an HDMI cable and HDMI adapter which is available from your device manufacturer.
PAGE 32
TROUBLESHOOTING Problem Solution IR remote is inoperative. • Verify that the batteries in the remote are fresh. • Verify that the remote sensor eye is not obstructed. • If the monitor is set to M1, press the M1 button on the remote control. If the monitor is set to M2, press the M2 button on the remote control. (See page 8.) Disc won't play. • Insert a disc with the label side facing upwards. • Check the type of disc you put into disc tray. This DVD only plays DVD, audio CD and MP3.
PAGE 33
Problem Solution Picture is distorted. • The disc might be damaged, try another disc. • It is normal for some distortion to appear during forward or reverse scan. No forward or reverse scan. • Some discs have sections that prohibit rapid scanning or title and chapter skip. • If you try to skip through the warning information and credits at the beginning of a movie, you won’t be able to. This part of the movie is often programmed to prohibit skipping through it.
PAGE 34
REPLACEMENT PARTS SPECIFICATIONS Remote Control 136-5326 LCD Backlighting LED Wireless Headphones 136-5301 Resolution 1024 (RGB) x 600 MVGP1 Game Module 136-5319 Pixels 1,843,200 Game Controller P1 136-5320 Operation Temperature 32 ~131º F (0 ~ 55º C) Game Controller P2 136-5321 Storage Temperature -4 ~ 158º F (-20 ~ 70º C) Back Light Life 20,000 Hours Video Display System NTSC / PAL Video Output 1.
PAGE 35
LIMITED WARRANTY R Applies to ADVENT Mobile Video Products VOXX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that, should this product or any part thereof (except game controllers), under normal use and conditions, be proven defective in material or workmanship within 36 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor.