ADV38 10.
Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in "park" or when the vehicle,s parking brake is applied.
MATERIALS INCLUDED IN THIS PACKAGE: 1) 2) 3) 4) 5) 6) 10.
Installing The Snap On Covers 1. ON OFF 2. 3. 4. 5. 6. Snap On Cover (Shroud) 1 Pewter, 1 Shale Snap On Cover (Screen Back Cab) 1 Pewter, 1 Shale Pry Tool Screw Cap (L & R) 2 Pewter, 2 Shale USB Cover AUTO Housing Place the pod on a soft surface to avoid damaging the plastic. Installing The Shroud catch catch Remove tape backing before installing. ON (A) OFF AUTO Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place.
Removing The Snap On Cover (Shroud) From The Housing Work on a soft surface to avoid damaging the plastic. Insert the supplied pry tool between the Housing and Snap On Cover (Shroud), then press the pry tool to release the Snap On Cover (Shroud). 1 2 3 Removing The Snap On Cover (Screen Back) From LCD The Housing Insert the supplied pry tool between the Housing and Snap On Cover (Screen Back), then press the pry tool to release the Snap On Cover (Screen Back).
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting.
TRIM RING INSTALLATION: Note: This page only covers special installation considerations for thick trim ring installation. If the video monitor is to be installed in a vehicle with the thick trim ring, it may need to be trimmed to fit the contour of the vehicle Headliner. Note: The trim rings supplied with this unit are not designed to be trimmed. 1) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof using the mounting screw bosses.
TRIM RING INSTALLATION: Supplied A) B) C) screws as below use for install Trim Ring to unit. Please refer illustration below. #4 x 5/16 Self Tapping Screws (1pc) #4 x 7/16 Self Tapping Screws (3pcs) Screws ISO 3 x 8mm Long (5pcs) A B C C C B C C B MOUNTING THE TRIM RING Roof Roof Support Headliner Mounting Bracket Self-drilling Screws Trim Ring Video Unit M5 Screw CAUTION: The 20mm and 40mm screws in the hardware kit are provided to facilitate installation.
WIRING DIAGRAM * Relay Box (OPTIONAL) FMDIRB * Antenna for Wireless FM Mod. ** See Antenna Note 12 Pin AV Adapter Cable AV1 Input *** Line Out-R (Red) Line Out-L (White) Figure A 2 Pin Power Wire Harness with choke Line Out-V (Yellow) 12 Pin Power / Signal harness Dome Light Power source AV OUTPUT Auxiliary Video Display 1) Make the connections to the vehicle for the 12 pin wiring harness.
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched system. Positive switched systems supply voltage to the interior lights to turn on, negative switched systems apply ground to illuminate the bulbs.
Negative Switched Dome Lighting To 12 pin connector Red / black - Lamp on Black / red - Lamp common Purple / brown - Lamp Auto To constant To constant Factory Door ajar switch or Body Control computer Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor.
© 2014 VOXX ELECTRONICS CORP., 150 Marcus Blvd.
