User Guide

3
Table 2. Keypad Power Connections
eludoMrolenaPlortnoCniP-kcaJlebaLgnitaRtnerruC
eludoMesaB9,8,7,6-2J21+1etoNAm006,1
eludoMnoisnapxE
7,5,3,1-1J21+
2etoN
4,3,2,1-3J21+
eludoMnInetsiL21,11-1J21+2etoN
)A-4MAA(eludoMsseccA
2-6J/5J/4J/3JV21+
Am054
6-2JV21+
eludoMsseleriW
)detsiLLUtoN(
4-2J21+2etoN
+C-4MAA/+4MAA
71-9J/8J/7J/6JDER
Am054
41,31-5JV21+
+1PC
11,01,9,8-7JV+
Am054
6,1-4JDER
5-7J*+LEBAm059
+2PC
6-1J+1XA
Am0078-3J1DER
21-3J2DER
4-PC
2-1JV21+
Am007
9,5-3JDER
71-4J+1XUA
91-4J+2XUA
tnerrucgniwardeunitnoctiucriclleB+1PCehtmorfderewopsdapyeK*
.nwodflestisrewop+1PCehtretfa
)94301890N/P("snoitcurtsnInoitallatsnIsulpegatnavdA"ehttlusnoC:1ETON
.noitacilpparuoyroftnerrucelbaliavamumixamehtrof
.)S-A1V21SPAroeludoMesaB(ecruosrewopnotnadnepeD:2ETON
LCD
plus
KEYPAD FAST/SLOW JUMPER
Each LCD plus keypad is shipped from the factory ready for
installation in fast RS-485 applications (Fast/Slow jumper in place).
Refer to Figure 3 and locate the jumper at the bottom left of the LCD
plus keypad’s circuit board.
LEAVE THIS JUMPER IN PLACE when using the LCD plus
keypad with AAM4-A & AAM4C-A access systems
CUT THIS JUMPER when using the LCD plus keypad with the
following:
ADV 3450* ADV 3250*
ADV 3650* AAM4+
ADV 3475* AAM4-C+
ADV 3350+*
*NOTE: These systems require version 6.0 (or higher)
firmware.
SETTING LCD
plus
KEYPAD ADDRESSES
Assign LCD plus keypad addresses in consecutive order, starting
with Address #1 and
not skipping any addresses:
Alarm Panel Zone A Keypads (0-3)
Alarm Panel Zone B Keypads (0-3)
AAM Module #1 Door #1
AAM Module #1 Door #2
AAM Module #7 Door #4
Table 3 will assist you in setting LCD PLUS keypad addresses.
Table 3. LCD plus Keypad Address Jumpering
Keypa
Addre
Keypad Jumper
#
Keypa
Addre
Keypad
Jumper#
1 2 4 8 1 2 4 8
1 X 9 X X
2 X 10 X X
3 X X 11 X X X
4 X 12 X X
5 X X 13 X X X
6 X X 14 X X X
7 X X X 15 X X X X
8 X 16
NOTE: X = jumper in place.
J2
1
JPR
J1
KP2
LCD
PLUS
CUT
FOR SLOW
ADDRESS
JUMPERS
8
4
2
1
90242
REV
S/N
1
2
3
4
5
6
7
8
9
10
11
12
13
BEEPOUT
GND
-DATA
+DATA
+12V IN
Figure 3. LCD plus Keypad Circuit Board