User manual
Table Of Contents
- Contents
- Chapter 1 Introduction
- Chapter 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating jumpers and Connectors
- 2.4 Setting Jumpers
- 2.5 Clear CMOS (JP2)
- 2.6 Installing DIMMs
- 2.7 IDE, CDROM hard drive connector (CN18)
- 2.8 Solid State Disk
- 2.9 Parallel port connector (CN17)
- 2.10 Keyboard and PS/2 mouse connector (CN15)
- 2.11 Front Panel Connector (CN5)
- 2.12 Power connectors (CN11,CN1)
- 2.13 Power ON/OFF switch con. pin 11-12 of CN5
- 2.14 Audio AC'97 Link interfaces (CN21)
- 2.15 COM port connector (CN19)
- 2.16 VGA/LVDS interface connections (CN26, CN22)
- 2.17 TV-out interface
- 2.18 Ethernet configuration (CN6, CN10)
- 2.19 USB connectors (CN12,CN13,CN14)
- 2.20 LCD Backlight connector (CN23)
- 2.21 SATA Connector (CN7, CN9)
- 2.22 DI/O connector (CN16)
- 2.23 CPU Fan power supply connector (CN11)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- 4.2.1 Entering setup
- 4.2.2 Standard CMOS Features setup
- 4.2.3 Advanced BIOS Features setup
- 4.2.4 Advanced Chipset Features setup
- 4.2.5 Integrated Peripherals
- 4.2.6 Power Management Setup
- 4.2.7 PnP/PCI Configurations
- 4.2.8 PC Health Status
- 4.2.9 Frequency/Voltage Control
- 4.2.10 Load Optimized Defaults
- 4.2.11 Set Password
- 4.2.12 Save & Exit Setup
- 4.2.13 Exit Without Saving
- Chapter 5 PCI Graphic Setup
- Chapter 6 Audio Setup
- Chapter 7 LAN Configuration
- Appendix A Prog. GPIO & W’dog Timer
- A.1 Supported GPIO Register
- A.2 Watchdog programming
- Table B.1: CN1 Power Connector
- Table B.2: CN2 LAN LED
- Table B.3: CN4 PCI -5V & -12V Input
- Table B.4: CN5 SYSTEM PANEL
- Table B.5: CN6 LAN1 CONNECTOR
- Table B.6: CN7 SATA2 connector
- Table B.7: CN9 SATA1 connector
- Table B.8: CN10 LAN2 CONNECTOR
- Table B.9: CN11 CPU FAN connector
- Table B.10: CN12 USB5/6 connector
- Table B.11: CN13 USB3/4 connector
- Table B.12: CN14 USB1/2 connector
- Table B.13: CN15 KB/MS
- Table B.14: CN16 GPIO
- Table B.15: CN17 Print Port connector
- Table B.16: CN18 IDE connector
- Table B.17: CN19 COM1/2/3/4 connector
- Table B.18: CN20 PC104+ Connector
- Table B.19: CN21 AUDIO connector
- Table B.20: CN22 LVDS Connector
- Table B.21: CN23 LCD Backlight
- Table B.22: CN24 CD_IN connector
- Table B.23: CN25 48bit LVDS Connector
- Table B.24: CN26 CRT connector
- Table B.25: CN27 SYS FAN connector
- Table B.26: CN28 Inverter connector
- Table B.27: CN29 SPK-OUT connector
- Table B.28: CN30 Compack II W/Ejector
- Table B.29: CN31 MINI PCI connector
- Table B.30: CN32 MIO USB connector
- Appendix C System Assignments
- Appendix D Optional Extras
- Appendix E Mechanical Drawings
- Appendix F AT/ATX Power setting
PCM-9584 User Manual 100
Appendix D Optional Extras
The PCM-9584 requires several cables for normal operation. You can
make them yourself or purchase an optional cable kit assembly, which
includes the following
D.1 PCM-10586-9584E Cable kit for PCM-9584
Table D.1: PCM-10586-9584E Cable kit for PCM-9584
Part No. Cable Descrip-
tion
PCM-9584
connector
Terminal Connector
1703060191 KB/Mouse
CABLE
CN15 Cable 6P-2.0mm Hous-
ing/ 6P (PS/2)/6P (K/B)
19cm
1703050106 TV-Out CABLE CN8 Cable 5P S/TV-Video out
10cm
1700260250 Parallel Port
CABLE
CN17 Cable 25cm 25P to 26P
ASSY LPT Port 2.0mm
1701400452 IDE CABLE CN18 FLAT CABLE 40P GRAY
FOR DMA-66 PIN20 I.P.
45CM
1700001296 VGA CRT
CABLE
CN26 VGA Cable D-SUB 15P to
16P 2.0mm L:150mm K
1700160160 Audio CABLE CN21 Cable 16Pin(2.0mm)
Audio 16cm PCM-5820/L
1701400181 COM1-4 CN19 FLAT CABLE 18CM
IDC40P 2.0mm/4COM
PCM-9570 USE
1700002142 LAN CABLE CN6.CN10 LAN Cable IDC10P
2.0mm/RJ45 20CM PCM-
9584
1700071000 SATA CABLE CN7.CN9 CABLE Serial ATA 7P/7P
100cm MOLEX
1703100260 USB CABLE CN12.CN1
3.CN14
"Wire 10P 26cm IDE
2.0mm For USB 2 PORT
1.9