User's Manual
Table Of Contents
- WISE-2834
- 1 Product Overview
- 2 Product Specification
- 3 Mechanical and Hardware Installation
- 4 System Configuration
- 5 Software Programming (Node- RED)
- 5.1 Terminology Definition
- 5.2 System Architecture
- 5.3 Graphic programming with Node-RED
- 5.3.1 Node-RED page
- 5.3.2 Tag Inventory
- 5.3.3 Tag Read
- 5.3.4 Tag Write
- 5.3.5 Tag Lock
- 5.3.6 Tag Kill
- 5.3.7 Tag Access Results
- 5.3.8 Get DIO value
- 5.3.9 Get counter value
- 5.3.10 Get counter status
- 5.3.11 Get DO pulse count and continue mode
- 5.3.12 Get latch status
- 5.3.13 Set DO value
- 5.3.14 Set counter value
- 5.3.15 Set DO pulse
- 5.3.16 Clear latch
- 5.4 API for Development
- A RFID node output
- B RFID module error code
- C RFID Frequency Channel Tables
- C.1 United States/Canada/Mexico Region Frequency Channel Table
- C.2 Europe Region Frequency Channel Table (ETSI EN 302 208)
- C.3 Europe2 Region Frequency Channel Table(ETSI EN 300 220)
- C.4 Taiwan Region Frequency Channel Table
- C.5 China Region Frequency Channel Table
- C.6 South Korea Region Frequency Channel Table
- C.7 Australia/New Zealand Region Frequency Channel Table
- C.8 Brazil Region Frequency Channel Table
- C.9 Israel Region Frequency Channel Table
- C.10 India Region Frequency Channel Table
- C.11 Japan Region Frequency Channel Table
- C.12 Japan2 Region Frequency Channel Table (with LBT)
75 WISE-2834 User Manual
Appendix B RFID module error code
0x0327 RFTC_ERR_BAD_RFLNA_GAIN_RE
Q
Set by the RFTC module if an unsup-
ported RFLNA gain level is requested.
0x0328 RFTC_ERR_BAD_IFLNA_GAIN_RE
Q
Set by the RFTC module if an unsup-
ported IFLNA gain level is requested.
0x0329 RFTC_ERR_BAD_AGCMIX_GAIN_R
EQ
Set by the RFTC module if an unsup-
ported AGC/MIXER gain level is
requested.
0x032A RFTC_ERR_HWOPT_BADFWDPWR
COMPOPT
Set by the RFTC module if an unsup-
ported compensation option is
detected at OEMCFG address 0xA1.
0x032B RFTC_ERR_INVALID_PLL_DIVIDER
_VALUE
This error is generated if the PLL
Divider Value is zero.
0x032C RFTC_ERR_SJC_EXTERNALLOTO
OLOW
This error is generated if the external
LO signal level is below the threshold
specified in register
HST_RFTC_SJC_EXTERNALLOTHR
SH.
0x032D RFTC_ERR_SJC_EXTERNALLONO
TSELECTED
This error is generated if SJC is
enabled, and the LO source is not
external.
0x032E RFTC_ERR_BADLOSOURCE This error is generated if the LO
source is incorrectly defined in the
OEM Config registers.
0x032F RFTC_ERR_GENERALRANDOMDA
TA
This error is generated if there is a
general error in the Random Data
Transmit function.
0x0330 RFTC_ERR_XVCR_HEALTH_CHEC
K_FAIL
This error is generated if there is
transceiver health check failure and
the handler is set to enable Mac Error.
See OEM Config
XCVR_HEALTH_CHECK_CFG.
0x0331 RFTC_ERR_INVALID_OEM_PROFIL
E_HEADER
This error is generated if the OEM
custom profile header is invalid.
0x0332 RFTC_ERR_AUTO_READ_RX_FIFO This error is generated if an error dur-
ing the Auto Read of the Rx FIFO
Read is detected.
0x0333 RFTC_ERR_DC_OFFSET_CALIBRA
TION
This error is general error generated if
an error occurs during the DC Offset
Calibration.
0x0334 RFTC_ERR_LBT_RSSI_CALIBRATI
ON
This error is general error generated if
an error occurs during the LBT RSSI
Calibration. If noise floor versus cali-
bration value do not have a significant
difference this error will occur. User
should check the injected reference
signal for level and frequency.
0x0335 RFTC_ERR_PA_BIAS_CAL_CONFI
G
This error is related to a PA Bias Cali-
bration Configuration error.
Table B.2: Error Code Details