User Manual UTC-515 Intel® AtomTM D525 Processorbased Ubiquitous Touch Computer with 15.
Copyright The documentation and the software included with this product are copyrighted 2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity FCC Class A Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Technical Support and Assistance 1. 2. Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Safety Instructions 1. 2. 3. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
UTC-515 User Manual vi
Contents Chapter 1 General Information ............................1 1.1 1.2 Introduction ............................................................................................... 2 General Specifications .............................................................................. 2 1.2.1 General ......................................................................................... 2 1.2.2 Standard PC functions .................................................................. 2 1.2.
4.2.2 Table 4.2: Jumper List............................................................... 27 Jumper Settings.......................................................................... 27 Table 4.3: J2: COM2 Setting ..................................................... 27 Table 4.4: J3: AT / ATX Power SEL .......................................... 27 Table 4.5: J4: Clear COMS ....................................................... 28 Table 4.6: J5: PAN VOL SEL ..............................................
Chapter 1 1 General Information This chapter gives background information on the UTC-515.
1.1 Introduction The UTC-515 is an Intel low-power Intel® AtomTM D525 processor computer that is designed to serve as a interactive self-service terminal and as a multimedia computer. It is a PC-based system with 15.6" TFT LCD display, on-board PCIe Ethernet controller, one COM port and VGA connector. With a built in internal Compact flash slot (for CF card), one SATA connector for HDD and an mini PCIe expansion socket, the UTC-515 is a compact and user-friendly multi-function computer.
Memory Size: Up to 224 MB of dynamic video memory allocation Interface: VGA Display mode: – CRT: Intel® Atom™ D525 up to 2048 x 1536 1.2.4 Audio function Audio: High Definition Audio (HD), 1 W x 2 Speakers Optional - Audio output function Chipset: LAN1 Intel 82567V, LAN2 Intel 82583V Speed: 1000 Mbps /Interface: 2 x RJ45 Wake-on-LAN: Supports Wake-on-LAN function with ATX power control Supports LAN teaming (in Fault Tolerance) 1.2.
1.2.8 Setup Boot up timer: A) If we will use Windows OS, after set up boot up timer under BIOS menu, we need to wait system boot into OS and then shut down the UTC-515 properly. Then the UTC-515 can boot up automatically at the timing we set. B) If we will use DOS, after set up boot up timer under BIOS menu, we need to wait until we see C:/ and then turn off the UTC-515 by power switch. Then the UTC515 can boot up automatically at the timing we set. 1.3 LCD Specifications Display type: 15.
Part No. Description 968EMW0038 Wireless IEEE 802.11 b/g/n AW-NE785 PCIE 1750006010 (Cable) 9680001060 2.0dBi Dipole short antenna 1750003222 5.0dBi Dipole long antenna Peripherals for UTC-500 series Part No.
1.5 Dimensions 218.25 40 48 40 Figure 1.1 Dimensions of UTC-515 UTC-515 User Manual 154.80 ANTENNA HOLE 236.50 384.
Chapter 2 2 System Setup This chapter details system setup on the UTC-515.
2.1 A Quick Tour of the UTC-515 Before you start to set up the UTC-515, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below. When you place the UTC-515 upright on the desktop, its front panel appears as shown in Figure 2.1. Figure 2.1 Front view of UTC-515 When you turn the UTC-515 around and look at its rear cover, you will find the I/O section as shown in Fig. 2.2.
B C D E F Chapter 2 A G H E. VGA F. DC Inlet G. Power Switch H. Compact Flash slot 2.2 Installation Procedures 2.2.1 Connecting the power cord The UTC-515 can be powered by a DC electrical outlet. Be sure to always handle the power cords by holding the plug ends only. Please follow the Figure 2.5 to connect the male plug of the power cord to the DC inlet of the UTC-515. 2.2.
2.3 Running the BIOS Setup Program Your UTC-515 is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the UTC-515's BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of hard drive. The setup program is stored in read-only memory (ROM).
After installing your system software, you will be able to set up the Ethernet, XGA, audio, and touchscreen functions. All drivers are stored in a CD-ROM disc entitled “Drivers and Utilities” which can be found in your accessory box. The various drivers and utilities in the CD-ROM disc have their own text files which helps users install the drivers and understand their functions. These files are a very useful supplement to the information in this manual.
UTC-515 User Manual 12
Chapter 3 3 Hardware Install and Upgrades This chapter details installing the UTC-515 hardware. Sections include: Overview of Hardware Installation and Upgrading Installing the 2.
3.1 Introduction The UTC-515 consists of a PC-based computer that is housed in an Aluminum extrusion. You can install a HDD, DRAM, and Compact Flash by removing the rear cover. Any maintenance or hardware upgrades can be easily completed after removing the rear cover. Warning! Do not remove the rear cover until you have verified that no power is flowing within the UTC-515. Power must be switched off and the power cord must be unplugged. Every time you service the UTC-515, you should be aware of this. 3.
1. Please follow the Compact Flash card assembly as in the following diagram. (Please notice the direction of the CF Card) 3.4 Installing the WLAN Reserve two locations for the external Antenna. One is at the IO port, the other is at the rear cover. Customers can choose based on different applications. 1. Remove 17 pcs screws of back cover. 15 UTC-520 User Manual Hardware Install and Upgrades Figure 3.2 Installing the Compact Flash card Chapter 3 3.
2. Remove the "hole cover" on back cover with a slot screwdriver. 3. Remove connectors on the M/B.
Remove 4 screws on M/B. 5. Take the M/B then remove the DC-in cable. 6. Coaxial cable (Advantech P/N: 1750006010) Chapter 3 4.
7. Put the black rubber gasket in SMA side first. 8. Connect the coaxial cable to "ANT1" on the WLAN card. 9. Install the WLAN card on M/B bottom side.
Chapter 3 10. Find the smooth side of the circle. Hardware Install and Upgrades 11. Install the cable into antenna bracket. 12. Install the washer & nut then screw in tight.
13. Put the M/B back and the 4 screws on the M/B. 14. Put the antenna bracket on the stand and insert the 2 screws 15. Caution! -Do not let the antenna wire go between the stand & bracket.
Chapter 3 Hardware Install and Upgrades 16. Assemble all the connectors back. 17. Replace the 17 screws on the back cover.
18. Assemble the Antenna. UTC-515 with the 5.0dBi dipole long antenna (Advantech P/N: 1750003222) UTC-515 with the 2.
Chapter 4 4 Jumper Settings and Connectors This chapter tells how to set up the UTC-515 hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installation procedures.
4.1 Jumpers and Connectors 4.1.1 Setting jumpers You can configure your UTC-515 to match the needs of your application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To 'close’ a jumper, you connect the pins with the clip. To ‘open’ a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
The motherboard of the UTC-515 has a number of jumpers and connectors that allow you to configure your system to suit your applications. The table below lists the function of each of the board’s jumpers. Table 4.
4.1.3 Locating jumpers and connectors CN5 CN1 CN3 CN20 CN11 CN14 CN15 CN16 CN25CN24 CN18 CN19 CN26 CN23 CN6 CN28 CN31 CN30 CN13 CN32 Figure 4.
Chapter 4 4.2 Jumpers 4.2.1 Jumper list Table 4.2: Jumper List COM2 Setting J3 AT / ATX Power SEL J4 Clear CMOS J5 Panel Voltage SEL 4.2.2 Jumper Settings Table 4.3: J2: COM2 Setting Part Number 1653003260 Footprint HD_3x2P_79 Description PIN HEADER 3*2P 180D(M) 2.0mm SMD SOUARE PIN Setting Function (1-2)* RS232 (3-4) RS485 (5-6) RS422 Table 4.4: J3: AT / ATX Power SEL Part Number 1653002101 Footprint HD_2x1P_79_D Description PIN HEADER 2*1P 180D(M)SQUARE 2.
Table 4.5: J4: Clear COMS Part Number 1653003101 Footprint HD_3x1P_79_D Description PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb Setting Function (1-2)* Normal (2-3) Clear CMOS Table 4.6: J5: PAN VOL SEL Part Number 1653003101 Footprint HD_3x1P_79_D Description PIN HEADER 3*1P 180D(M) 2.
Appendix A A I/O Pin Assignments
A.1 PIN Assignments Table A.1: CN1: Audio Part Number 1653205260 Footprint HD_5x2P_79_BOX Description BOX HEADER SMD 5*2 180D (M) 2.0mm Pin Pin Name 1 LOUTR 2 LINR 3 GND 4 GND 5 LOUTL 6 LINL 7 GND 8 GND 9 MIC1R 10 MIC1L Matching Cable: 1703100152 Table A.2: CN3: SATA Part Number 1654002320 Footprint FOX_LD1107V-S33T5 Description Serial ATA 7P 1.
Appendix A I/O Pin Assignments Table A.3: CN5: SATA HDD Power Part Number 1655306020 Footprint WHL6V-2M Description WAFER BOX 2.0mm 6P 180D(M) W/LOCK Pin Pin Name 1 +5V 2 GND 3 NC 4 GND 5 NC 6 NC Table A.4: CN6: 12 V Power Input Part Number 1655404090 Footprint ATXCON-2X2-42 Description ATX PWR CONN. 2*2P 180D 4.
Table A.5: CN11: SMBus Part Number 1655904020 Footprint FPC4V-125M Description Wafer SMT 1.25mmS/T type 4P 180D(M) 85205-04001 Pin Pin Name 1 GND 2 SMB_DAT 3 SMB_CLK 4 +5V Table A.6: CN13: Inverter Power Output Part Number 1655000453 Footprint WHL5V-2M-24W1140 Description WAFER BOX 2.
Part Number 1653005260 Footprint HD_5x2P_79_N10 Description PIN HEADER 2*5P 180D(M) 2.0mm SMD IDIOT-PROOF Pin Pin Name 1 +5V 2 +5V 3 A_D- 4 B_D- 5 A_D+ 6 B_D+ 7 GND 8 GND 9 GND Matching Cable: 1703100121 Table A.8: CN15: Internal USB Part Number 1653005260 Footprint HD_5x2P_79_N10 Description PIN HEADER 2*5P 180D(M) 2.
Table A.9: CN16: 18 or 24 bits LVDS Panel Part Number 1653910261 Footprint SPH10X2 Description *CONN. SMD 10*2P 180D(M)DF13-20DP-1.25V(91) HRS Pin Pin Name 1 GND 2 GND 3 LVDS0_D0+ 4 NC 5 LVDS0_D0- 6 NC 7 LVDS0_D1+ 8 NC 9 LVDS0_D1- 10 NC 11 LVDS0_D2+ 12 NC 13 LVDS0_D2- 14 NC 15 LVDS0_CLK+ 16 LVDS0_z_D3+ 17 LVDS0_CLK- 18 LVDS0_z_D3- 19 +5V or +3.3V 20 +5V or +3.
Part Number 1652002996 Footprint RJ45_14P_RTA-195AAK1A Description Phone Jack RJ45 14P 90D(M) DIP RTA-195AAK1A Pin Pin Name Table A.11: CN19: LAN2 Part Number 1652002996 Footprint RJ45_14P_RTA-195AAK1A Description Phone Jack RJ45 14P 90D(M) DIP RTA-195AAK1A Pin Pin Name Table A.12: CN20: Power Switch (Low Active) Part Number 1655302020 Footprint WF_2P_79_BOX_R1_D Description WAFER BOX 2P 180D(M) 2.
Table A.13: CN22: HDMI (Optional) CN22 HDMI Part Number 1654009225 Footprint HDMI_19P_QJ51193-FFD4-4F Description HDMI Conn 19P 0.
Appendix A I/O Pin Assignments Table A.14: CN23: Reset Part Number 1655302020 Footprint WF_2P_79_BOX_R1_D Description WAFER BOX 2P 180D(M) 2.0mm W/Lock Pin Pin Name 1 RESET# 2 GND Table A.15: CN24: External USB Part Number 1654904105 Footprint USB-V-4A Description USB CON.
Table A.16: CN25: External USB Part Number 1654904105 Footprint USB-V-4A Description USB CON. 4P 90D(F) DIP A TYPE RoHS Pin Pin Name 1 +5V 2 D- 3 D+ 4 GND Table A.17: CN26: COM1 Part Number 1654000056 Footprint DBCOM-VM5MS Description D-SUB CON.
Part Number 1654000055 Footprint DBVGA-VF5MS Description D-SUB Conn. 15P 90D(F) DIP 070242FR015S200ZU Pin Pin Name 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 NC 10 GND 11 NC 12 DDAT 13 HSYNC 14 VSYNC 15 DCLK 39 UTC-515 User Manual Appendix A I/O Pin Assignments Table A.
Table A.19: CN28: Mini PCIE lock Part Number 1654002539 Footprint FOX_AS0B226-S68K7F_HOLDER Description MINI PCI Express LATCH 52P 90D SMD 6.8mm Pin Pin Name Table A.20: CN29: Mini PCIE slot Part Number 1654002538 Footprint FOX_AS0B226-S68K7F Description MINI PCI express 52P 90D SMD H=6.8mm Pin Pin Name 1 WAKE# 2 +3.3V or +3.3VSB 3 NC 4 GND 5 NC 6 +1.
Appendix A I/O Pin Assignments Table A.20: CN29: Mini PCIE slot 16 NC 17 NC 18 GND 19 NC 20 NC 21 GND 22 PERST# 23 PERn0 24 +3.3VSB 25 PERp0 26 GND 27 GND 28 +1.5V 29 GND 30 SMB CLK 31 PETn0 32 SMB DAT 33 PETp0 34 GND 35 GND 36 USB D- 37 GND 38 USB D+ 39 +3.3V or +3.3VSB 40 GND 41 +3.3V or +3.3VSB 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC 52 +3.3V or +3.
Table A.21: CN30: DDR3 SODIMM Part Number 1651001904 Footprint DDR-SODIMM-STD65 Description SKT DIMM 200P DDR2 H=6.
Appendix A I/O Pin Assignments Table A.21: CN30: DDR3 SODIMM 24 GND 25 DQ54 26 DM6 Table A.22: CN32: CF Part Number 1653002919 Footprint CF_50P_CFCMD-35T15W100 Description CF Type2 Conn.
Table A.
Appendix B B Peripherals Installation Guide
B.1 UTC-500 Peripherals Series Installation Guide Model UTC-P01-A0E UTC-P02-A0E UTC-P03-A0E UTC-P06-A0E Description 2M Camera Module for UTC-500 Series Magnetic Stripe Card Reader for UTC-500 Series RFID Reader for UTC-500 Series Smart Card Reader for UTC-500 Series Packing List UTC-PXX CD-Driver Cable Clamp x 2 Assemble the UTC-Peripherals 1. Attach the UTC-peripheral to the UTC 500 series side groove.
Fasten the 2 screws to fix the peripheral in place. 3. Connect the cable to an I/O port (USB). 4. Choose a location to put the cable clamp and attach the cable to it. Appendix B Peripherals Installation Guide 2.
Attaching a peripheral on the bottom of the unit An attachment to the left side UTC-515 User Manual 48
Appendix C WDT C
C.1 Watchdog Timer Sample Code Watchdog function: ;The SCH3114 Runtime base I/O address is A00h ;Setting WatchDog time value location at offset 66h ;If set value "0", it is mean disable WatchDog function. Superio_GPIO_Port = A00h mov dx,Superio_GPIO_Port + 66h mov al,00h out dx,al .model small .486p .stack 256 .data SCH3114_IO EQU A00h .code org 100h .
51 UTC-515 User Manual Appendix C WDT ;WD timer counting = 0 ;==================================================== mov dx,SCH3114_IO + 68h mov al,01h out dx,al .
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
53 XXX-XXXX User Manual
