UNO-2173A/AF Intel Atom Fanless Box PC with 1 x LAN, 2 x COM, Mini-PCIe User Manual
Copyright This document is copyrighted, © 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Product Warranty Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. FCC Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Safety Instructions Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from humidity.
TURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. 23. The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
Contents Chapter 1 Overview ...........................................................2 1.1 1.2 1.3 1.4 Introduction ....................................................................... 2 Hardware Specifications ................................................... 3 Safety Precautions ............................................................. 5 Chassis Dimensions........................................................... 6 Figure 1.1:UNO-2173A Chassis Dimensions................. 6 Figure 1.
Appendix A System Settings and Pin Assignments ..........24 A.1 System I/O Address and Interrupt Assignment....... 24 A.2 Board Connectors and Jumpers....................................... 26 A.3 A.4 A.5 A.6 A.7 A.8 A.9 RS-232 Standard Serial Port (COM1~COM2) ............... 27 RS-422/485 Serial Port (UNO-2173AF)......................... 28 Power Connector (PWR)................................................. 28 PS/2 Keyboard and Mouse Connector ............................ 29 USB Connector .........
CHAPTER 1 2 Overview This chapter provides an overview of UNO-2173A/AF’s specifications.
Chapter 1 Overview 1.1 Introduction UNO-2173A/AF is an embedded Application Ready Platform (ARP) that can shorten your development time and offers rich networking interfaces to fulfill extensive needs in different projects. Advantech’s Universal Network Controller is designed to be a total solution for network enabled Application Ready Platforms. Leveraging field-approved and worldwide approved real-time OS technology, Advantech’s UNO-2000 series provides a Windows CE .
1.2 Hardware Specifications General • Certifications Energy Star, CE, FCC class A, UL, CCC • Dimensions (W x D x H)255 x 152 x 59 mm (10" x 6.0" x 2.3") • Enclosure Aluminum +SECC • Mounting Wallmount, DIN-rail, VESA • Industrial Grounding Isolation between chassis and power ground • Power Consumption 15 W (Typical) • Power Requirements 9 ~ 36 VDC (Min. 36 W), ATX • Weight 2.5 kg • OS Support Windows XPe/XP/CE 5.0 & 6.
I/O Interface • Serial Ports 2 x RS-232 • Serial Port Speed 50 ~ 115.2 kbps • LAN 1 x 10/100/1000 Base-T RJ-45 ports (Built-in boot ROM in flash BIOS) • USB Ports 2 x USB 2.
1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. Warning! Always disconnect the power cord from your chassis whenever you are working on it. Do not connect while the power is on. A sudden rush of power can damage sensitive electronic components. Only experienced electronics personnel should open the chassis. Caution! Always ground yourself to remove any static electric charge before touching UNO-2173A/AF.
1.4 Chassis Dimensions 254.80 241.80 141.60 111.09 149.24 Ø4.00 4.00 Ø5.40 5.40 10.51 228.20 58.71 2.00 Figure 1.
254.80 241.80 141.60 111.09 149.24 Ø4.00 4.00 Ø5.40 5.40 10.51 228.20 58.71 2.00 Figure 1.
1.
CHAPTER 2 2 Hardware Functionality This chapter shows how to setup the UNO-2173A/AF’s hardware functions, including connecting peripherals, setting switches and indicators.
Chapter 2 Hardware Functionality 2.1 Introduction The following two figures show the connectors on UNO-2173A/AF. The following sections give you detailed information about function of each peripheral. Figure 2.1: Front panel of UNO-2173A/AF Figure 2.2: Rear panel of UNO-2173AF 2.2 RS-232 Interface (COM1~COM2) The UNO-2173A/AF offers two standard RS-232 serial communication interface ports: COM1 and COM2. Please refer to A.3 for their pin assignments.
2.3 RS-422/485 Interface (UNO-2173AF) The UNO-2173AF offers one RS-422/485 serial communication interface ports: COM3. Please refer to Appendix A.4 for their pin assignments. The default setting of COM3 is RS-422. 2.3.1 RS-422/485 Selection The mode of UNO-2173AF COM3 can be selected in the BIOS. Please enter the BIOS setting screen and select the "Integrated Peripherals", then the follow screen would be shown. In the screen you can configure the resource and the mode. 2.3.
2.3.3 Termination Resistor (SW3) The onboard termination resistor (120 ohm) for COM3 can be used for long distance transmission or device matching. (Default Open.) Table 2.1: Terminal Resistor for COM3 SW3 DIP1 DIP2 Status ON Add termial resistor on Tx+/Tx- of RS-422 or Data+/Data- of RS-485 OFF Open (default) ON Add termial resistor on Rx+/Rx- of RS-422 OFF Open (default) 2.4 LAN: Ethernet Connector UNO-2173A is equipped with one Giga LAN controller and UNO2173AF has two.
2.7 USB Connector The USB interface supports Plug and Play, which enables you to connect or disconnect a device whenever you want, without turning off the computer.UNO-2173A provides two and UNO-2173AF provides four connectors of USB interfaces, which gives complete Plug & Play and hot swapping for up to 127 external devices. The USB interface complies with USB EHCI, Rev. 2.0 compliant. The USB interface can be disabled in the system BIOS setup. Please refer to Appendix A.7 for its pin assignments. 2.
2.9.1 Lithium Battery Specification • Type: BR2032 (Using CR2032 is NOT recommended) • Output voltage: 3 VDC • Location: BH2, please refer to below figure Figure 2.3: Lithium Battery Location Note: BH2 is for SRAM and BH1 is for Real Time Clock 2.10 Power Button / Power Management Press the "PWR" button to power on or power off UNO-2173A/AF (ATX type). UNO-2173A/AF supports the ACPI (Advanced Configuration and Power Interface).
2.11 Reset Button Press the "Reset" button to activate the hardware reset function. 2.12 HD Audio ( UNO-2173AF) UNO-2173AF is equipped with ALC888-GR which is a High Definition Audio Codec. UNO-2173AF provides 3 phone jack connector for 5.1 channel output. Please configure the function through provided software utility. 2.13 PCI Express Mini Card Socket UNO-2173A/AF supports one socket for PCI Express mini Card. This interface is mainly target on the wireless application such as WLAN and GPRS.
UNO-2173A/AF User Manual 16
CHAPTER 3 2 Initial Setup This chapter introduces how to initialize the UNO-2173A/AF.
Chapter 3 Initial Setup 3.1 Inserting a CompactFlash Card 1. Remove the power cord. 2. Unscrew the two screws of CF cover in the front panel. 3. Plug a CompactFlash card with your OS and application program into a CompactFlash card slot on board. 4. Screw back the CF cover to ensure IP40 protection. Note: The CompactFlash is allocated as "the Secondary IDE Master" by default. User can change it to "Primary IDE Master" by BIOS setting.
3.3 Connecting Power Connect the UNO-2173A/AF to a 9~36 VDC power source. The power source can either be from a power adapter or an in-house power source. 3.4 Installing a Hard Disk The procedure for installing a hard disk into the UNO-2173A/AF is below. Please follow these steps carefully. 1. Remove the power cord. 2. Unscrew the six screws from the bottom panel. 3. Install the HDD on the HDD bracket. 4.
3.5 Installing a Wireless LAN Card and Antenna Please contact Advantech to prepare the following optional kit: Rear Panel for Antenna. • 1960032715N040 for UNO-2173A • 1960032715N020 for UNO-2173AF • The internal cable : 1700001854 (11cm) Wireless Module ( PCI Express mini card ) • One of the suggested module is 968EMW0006 which is a verified Wireless IEEE 802.
Antenna • Please select the necessary specification according to your application. • One of the suggested antenna is 1750003222 (18 cm) which is a verified 802.11b/g 5dBi Dipole Antenna Then follow the below steps for the installation: 1. Unscrew the bottom panel and open it. 2. Install the internal cable 1700001854 on the prepared rear panel with the hole of antenna (1960032715N040 or 1960032715N020). 3. Replace the original rear panel with the panel assembled in step 2. 4.
6. Screw back the bottom panel. 7. Assemble the antenna on the SMA connector. 3.6 BIOS Setup Press "DEL" in the boot-up screen to enter the BIOS setup utility. Please follow the instruction on the screen to do the necessary settings. Please note that you can try to “Load Optimized Defaults” from the BIOS Setup manual if the UNO-2173A/AF does not work properly.
Appendix A System Settings and Pin Assignments
Appendix A System Settings and Pin Assignments A.1 System I/O Address and Interrupt Assignment Table A.
Table A.2: UNO-2173A/AF Interrupt Assignment Interrupt No.
A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-2173A/AF board. The following sections tell you how to configure the UNO-2173A/AF hardware setting. Figure A-1 shows the locations of UNO-2173A/AF’s connectors and jumpers. Figure A.1: Connector & Jumper Locations (front) Table A.
A.3 RS-232 Standard Serial Port (COM1~COM2) Table A.
A.4 RS-422/485 Serial Port (UNO-2173AF) Table A.5: RS-422/485 serial port pin assignments Pin RS-422 RS-485 1 TX+ Data+ 2 TX- Data- 3 RX+ 4 RX- 5 GND A.5 Power Connector (PWR) Table A.
A.6 PS/2 Keyboard and Mouse Connector 6 5 4 3 2 1 Table A.7: Keyboard and Mouse connector pin assignments Pin Signal Name 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB Clock 6 MS Clock A.7 USB Connector Table A.
A.8 VGA Display Connector 5 1 10 6 15 11 Table A.
A.9 LVDS and LVDS_PWR (UNO-2173AF) A.9.1 LVDS Table A.
A.9.2 LVDS Power Setting (CN17) Table A.11: CN17 Configuration Configuration 1 2 3 4 5 6 1 2 3 4 5 6 Function VDD_DSUB (Pin 7 and Pin 20) of LVDS pin is +5V VDD_DSUB (Pin 7 and Pin 20) of LVDS pin is +3.3V A.9.3 LVDS_PWR (Backlight Control) 1 5 9 6 Table A.12: LVDS_PWR pin definition Pin Signal 1 +12V (1.
A.10 Clear CMOS (CN3) This jumper is used to erase CMOS data and reset system BIOS information. Follow the procedures below to clear the CMOS. 1. Turn off the system. 2. Close jumper CN3 (1-2) to clear CMOS . 3, Remove jumper CN3(1-2) 3. Turn on the system. The CMOS is now cleared. 4. Turn on the system. The BIOS is reset to its default setting. Table A.
UNO-2173A/AF User Manual 34
