User Manual TREK-570 Computer
Copyright The documentation and the software included with this product are copyrighted 2010 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
Technical Support and Assistance 1. 2. Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
Ordering Information P/N Description TREK-570-HWB7A0E TREK-570-HWB7B0E TREK-570 w/LTE(EU)/GPS/WLAN/BT/WES7 TREK-570 w/LTE(USA)/GPS/WLAN/BT/WES7 Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.
only with same or equivalent type recommended by the manufacture. Discard used batteries according to the manufacturers instructions. 17. THE COMPUTER IS PROVIDED WITH CD DRIVES COMPLY WITH APPROPRIATE SAFETY STANDARDS INCLUDING IEC 60825. 18. This device complies with Part 15 of the FCC rules.
eration of equipment nameplate ratings should be used when addressing this concern. E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips)." Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage.
Contents Chapter Chapter 1 General Information ............................1 1.1 1.2 1.3 Introduction ............................................................................................... 2 General Specifications .............................................................................. 3 Dimensions ............................................................................................... 5 Figure 1.1 TREK-570 dimensions................................................
4.2 Chapter 5 Pin Assignments ............................... 23 5.1 5.2 5.3 5.9 Front Side Connectors ............................................................................ 24 Rear Side Connectors............................................................................. 24 Power Connector (12/24 V; 6 ~ 36 V) ..................................................... 24 Table 5.1: Power Connector...................................................... 24 Smart Display Connector .....................
6.4 6.6 6.7 GPIO Test ............................................................................................... 36 Figure 6.11DI/O test ................................................................... 36 Figure 6.12Digital in .................................................................... 36 Figure 6.13Digital out.................................................................. 37 Video in Test ...........................................................................................
Chapter 1 1 General Information This chapter gives background information on the TREK-570 InVehicle Computing Box.
1.1 Introduction TREK-570 is a compact and economical vehicle-grade, Intel Atom E3826 SOC empowered computing box mainly designed for fleet management market. It can work in extreme environments with features like the wide working temperature range (-30-70℃) and anti-shock/vibration to pass MIL-STD-810G and 5M3 standard. Its special power protection surges from impacting the system. guarding against damage from transient card power.
Specifications Dimensions: (W x H x D): 229.6 x 71 x 117.9 mm Weight: 2 kg Vehicle power feature: – Input voltage: 6 ~ 32 Vdc, support ignition cold crank – Supports Ignition on/off – Supports low battery shut-down protection threshold (optional) – Supports power off event delay – Supports power on delay – Supports power low delay – Supports power low hard delay – Supports hard off delay Note! For more detail of function please refer to Chapter 6, Section 6.3 of this manual.
Note! This product is covered by one or more of the following patents: US5,307,459, US5,434,872, US5,732,094, US6,570,884, US6,115,776 and US6,327,625. Storage: 1x Mini PCI express bus expansion slot for m-SATA: SATA rev2.0 bus Video output: 1 X LVDS output by Smart Display port 1 x VGA output by DB-15 1 x HDMI output by HDMI 19pin Receptacle *note: 2 of 3 video output can be displayed simultaneously in BIOS or OS.
Chapter 1 1.3 Dimensions General Information Figure 1.
Chapter 2 2 System Setup This chapter details system setup on TREK-570 Sections include: A Quick Tour of the Computer Box Installation Procedures Running the BIOS Setup Program TREK-570/303 User Manual 6
2.1 A Quick Tour of the TREK-570 Computing Box Before starting to set up the In-Vehicle Computing Box, take a moment to become familiar with the locations and functions of the controls, drives, connectors and ports, which are illustrated in the figures below. When the Computer box is placed inside truck glove cabinet or under the passenger’s seat next to the driver, its front appears as shown in Figure 2.1. Figure 2.1 Front view of TREK-570 Figure 2.
2.2.1 Connecting the Power Cord Note! Ignition on/off setting: The TREK-550 A2 supports an ignition on/off function so that you can power on/off the TREK-550 A2 via the ignition signal/voltage and connect the TREK-550 A2 vehicle ignition switch. Table 2.1: Pin Definition of Power Cord Pin Definition Color 1 3 4 + Ignition Red Black Orange 2.2.2 Power Connector Figure 2.
2.3 Booting up the System In most cases, the computer will have been properly set up and configured by the dealer or SI prior to delivery. However, it may still be necessary to adjust some of the computer's BIOS (Basic Input-Output System) setup programs to change the system configuration data, like the current date and time, or the specific type of hard drive currently installed. The setup program is stored in read-only memory (ROM).
Chapter 3 3 Hardware & Peripheral Installation This chapter details the installation of hardware for TREK-550 A2.
3.1 Overview of Hardware Installation & Upgrading The In-Vehicle Computing Box consists of a PC-based computer that is housed in a ruggedized aluminum enclosure. Any maintenance or hardware upgrades can be completed after removing the bottom cover plate. Warning! Do not remove the ruggedized aluminum covers until verifying that no power is flowing within the computer. Power must be switched off and the power cord must be unplugged. Take care in order to avoid injury or damage to the equipment. 3.
Figure 3.1 Install peripheral in the system 3.3.3 installing the MiniPCI Type WWAN, SIM Card and Coin Battery The WWAN module is on the Mini PCI slot can be easily installed, just undo the 6 screws from the bottom cover to install WWAN, SIM card, and battery. 3.3.4 GPS Module The GPS module is not to be installed by the customer with breaking the warranty. 3.
TREK-570/303 User Manual 16
Chapter 4 4 Jumper Settings and Connectors This chapter explains how to set up the In-Vehicle Computing Box hardware, including instructions on setting jumpers and connecting peripherals, and how to set switches and read indicators. Be sure to read all the safety precautions before beginning the installation procedure.
4.1 Setting Jumpers and Switches It is possible to configure the In-Vehicle Computing Box to match the needs of the application by resetting the jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip, often protected by a plastic cover that slides over the pins to connect them. To “close” a jumper, connect the pins with the clip. To “open” a jumper, remove the clip. Sometimes a jumper has three pins, labeled 1, 2, and 3.
Chapter 5 5 Pin Assignments This chapter explains pin assignments on the TREK-550 A2.
5.1 Front Side Connectors 5.2 Rear Side Connectors 5.
Chapter 5 5.
5.6 RS-232 (COM9) / RS-485 (COM5) / J1708 (COM6) Connector Table 5.4: RS-232 / RS-485 / J1708 Connector Pin Signal Pin Signal 1 3 5 7 9 RS-232 RTS RS-232 TXD Ground RS-485 D+ J1708 D+ 2 4 6 8 RS-232 RXD# RS-232 CTS RS-485 DJ1708 D- 5.
Chapter 5 Pin Assignments
TREK-570/303 User Manual 28
Chapter 6 6 Software Demo Utility Setup This appendix explains the software demo utility for TREK-550 A2.
6.1 Introduction To make the hardware easier to access for programmers, Advantech has developed and demo program in order to let customer test the functions on TREK-572. This document describes detailed information for each Advantech demo program so that application developers can become more familiar with using them. For technical support, contact Advantech application engineers worldwide. For news updates, visit our website: www.advantech.com 6.
z z z z z z Library Version Firmware Version Reset firmware to default (CAN/J1939/OBD2) Channel 1 bus type control (CAN/J1939/OBD2) Channel 2 bus type control (J1708/J1587) Channel 1 bus type control Note: Each channel only can select one bus type at same time.
J1708 Page J1708 page as below figure z z z z z Read Data control (Press "Start" to monitor bus to read) Read Data list Write Data control J1708 bus message filter control Message filter list J1939 Page J1939 page as below figure z z z z z Read Data control (Press "Start" to monitor bus to read) Read Data list Write Data control J1939 bus message filter control J1939 Address mapping TREK 570/303 User Manual 32
J1587 Page J1587 page as below figure z z z z z Read Data control (Press "Start" to monitor bus to read) Read Data list Write Data control J1587 bus message filter control Message filter list ODB2 Page ODB2 page as below figure z z z z Read Data control (Press "Start" to monitor bus to read) Read Data list Write Data control ODB2 bus message filter control 33 TREK-570/303 User Manual
6.1.2 Testing VCIL 1. Opening "TREK_V3_Sample_Code_VCIL.exe" 2. Select VCIL port and speed for your platform. For example, select the port number 8 on TREK-674 3. Selecting "VCIL Control" page as below figure 4. You should see the firmware version on this page when success opening VCIL.
Bus Type Control 1. Selecting "VCIL Control" page 2. Press combo box on the channel which you want to configure as below figure 3. Selecting Bus type Note: Each channel only can select one bus type at same time. Reset Module 1. Selecting "VCIL Control" page 2. Press "Reset Module" button as below figure CAUTION: When reset module, all configure for each bus reset to default value. 6.1.
1. Selecting "VCIL Control" page 2. Press combo box on the channel and select "CAN" as below figure Reading Data 1. Selecting "CAN" page as below figure Set CAN bus speed. For example 250K 2. Checked "Show Data" 3. Press "Start" button to receive CAN bus data 4. You should see the data came from the CAN bus and show on the list Writing Data 1.
Set CAN bus speed. For example 250K 2. Filling the CAN bus data prepare to send 3. Press "Write" button to send CAN bus data as above figure 4. You should see the data on the receiver Testing Message Mask 1. Selecting "VCIL Control" page 2.
1. Selecting "CAN" page as below figure 2. 3. 4. 5. Set CAN bus speed. For example 250K Configure the Message mask Press "Set Mask" button to apply the mask to bus You should see the mask was applied on the bus. If you set a mask to bus.
1. Selecting "VCIL Control" page 2. Press combo box on the channel and select "J1939" as below figure Reading Data 1. Selecting "J1939" page as below figure 2. Checked "Show Data" 3. Pull TrackBar "ON" to receive J1939 data 4. You should see the data came from the J1939 and show on the list Writing Data 1.
2. Filling the J1939 data prepare to send 3. Press "Write" button to send J1939 data as above figure 4. You should see the data on the receiver Testing Message Filter 1. Selecting "VCIL Control" page 2. Press combo box on the channel and select "J1939 + Mask" as below figure Set Message Filter 1.
2. 3. 4. 5. Select Channel and specified PGN to filter Press "Add Channel, PGN" button to add the rule to filter You should see the filter was applied on the bus The system ignores all PGN is not on the list For example, as above figure setting. The system can receive the PGN equal to 0xFEF6, otherwise no. 6.1.5 Testing ODB2 1. Selecting "VCIL Control" page 2. Press combo box on the channel and select "ODB2" as below figure Reading Data 1.
2. Checked "Show Data" 3. Pull TrackBar "ON" to receive ODB2 data 4. You should see the data came from the ODB2 and show on the list Writing Data 1. Selecting "ODB2" page as below figure 2. Filling the ODB2 data prepare to send 3. Press "Write" button to send ODB2 data as above figure 4. You should see the data on the receiver Testing Message Filter 1. Selecting "VCIL Control" page 2.
Set Message Filter 1. Selecting "ODB2" page as below figure 2. 3. 4. 5. Select Channel and specified PID to filter Press "Add Channel, PID" button to add the rule to filter You should see the filter was applied on the bus The system ignores all PID is not on the list For example, as above figure setting. The system can receive the PID equal to 0x00, otherwise no.
6.1.6 Testing J1708 1. Selecting "VCIL Control" page 2. Press combo box on the channel and select "J1708" as below figure Reading Data 1. Selecting "J1708" page as below figure 2. Checked "Show Data" 3. Press "Start" button to receive J1708 data 4. You should see the data came from the J1708 and show on the list Writing Data 1.
2. Filling the J1708 data prepare to send 3. Press "Write" button to send J1708 data as above figure 4. You should see the data on the receiver Testing Message Filter 1. Selecting "J1708" page as below figure 2. 3. 4. 5.
6.1.7 Testing J1587 1. Selecting "VCIL Control" page 2. Press combo box on the channel and select "J1587" as below figure Reading Data 1. Selecting "J1587" page as below figure 2. Checked "Show Data" 3. Press "Start" button to receive J1587 data 4. You should see the data came from the J1587 and show on the list Writing Data 1.
2. Filling the J1587 data prepare to send 3. Press "Write" button to send J1587 data as above figure 4. You should see the data on the receiver Testing Message Filter 1. Selecting "J1587" page as below figure 2. 3. 4. 5.
6.3.1 Power Management Mechanism The feature of Vehicle Power Management (VPM) is provided for users to fulfill the special requirements on in-vehicle applications. TREK 570/303 User Manual 48 Software Demo Utility Setup Ignition on/off – Turn on the system by ignition For the cases of in-vehicle applications, an ignition signal is often used to turn on or shutdown the system.
LOW_DELAY stage and start to count down. During the stage of LOW_DELAY countdown, if battery voltage is back above LOW_THRESHOLD, the VPM controller will stop counting down and exit. If LOW_DELAY counts to zero, the VPM controller will send an event (power button press) to notify the system, go into LOW_ HARD_DELAY stage and start to count down. Once LOW_ HARD_DELAY counts to zero, the VPM controller will cut off the system power abruptly to avoid draining out the car battery.
TREK V3 VPM Sample Code is demonstration of vehicle power management (VPM). System Menu • TREK V3 VPM Sample Code as below figure • VPM Common page as below figure TREK-570/303 User Manual 38 Software Demo Utility Setup Common page Low Battery Protection & Ignition Control page Backup Battery Information page Alarm Wakeup Control page Common page 1. 2. 3. 4. Chapter 6 6.3.
Library Version Firmware Version Car Battery Mode (Decide LBP what voltage mode to use) Current Battery Voltage Ignition Status Mode Control Wakeup Source Control Low Battery Protection & Ignition Control page 1. 2. 3. 4. 5. 6. 7. • VPM Low Battery Protection & Ignition Control page as below figure 1. Low Battery Protection Control 2.
• VPM Common page as below figure 1. Alarm wakeup Status Control 2. RTC Timer Control 3. Alarm Wakeup Time Control Testing VPM 1. Opening "TREK_V3_Sample_Code_VPM.exe" 2. You should see the firmware version and voltage below figure 6.4 WatchDog Sample Code TREK V3 Watch Dog Sample Code is demonstration of controlling Watch Dog.
System Menu • TREK 1. 2. 3. 4. 5. V3 Watch Dog Sample Code as below figure Library Version Range of Watch Dog timer Set/Get Watch Dog time Enable Watch Dog timer Reload the watchdog timer to prevent the system from rebooting Testing Watch Dog 1. Opening "TREK_V3_Sample_Code_Watch_Dog.exe" 2. Press "Get Range" button to check the range of watch dog timer 3. Input the time which you want system keep alive. For example 1 minute as below figure 4.
System Menu • TREK V3 Peripheral Control Sample Code as below figure below figure 1. Library Version 2. Select Peripheral 3. Select Set or Get function Testing Peripheral Control Getting Peripheral Power Status 1. 2. 3. 4. 5. Opening "TREK_V3_Sample_Code_PeripheralCtrl.exe" Selecting module, For example "WIFI". Selecting "Get" radio button Press "Apply" button You should see the peripheral power status as For example. Selecting WIFI module. I can see the WIFI module is enable.
If you want close the specified peripheral power, following the instruction: 1. 2. 3. 4. 5. 6. Opening "TREK_V3_Sample_Code_PeripheralCtrl.
Appendix A A TREK-303 This appendix explains the TREK303 detailed information.
A.1 TREK-303 Specifications Table A.1: TREK-303 Specification Models TREK-303R-LA0E TREK-303R-HA0E Design compatible models Paired with TREK-510 Paired with TREK-550 A2 Resoultion (pixel) Number of colors Pixel pitch Display Brightness (cd/m2) 480 x 234 262 K (supports 18-bit) 0.107(W) x 0.37 (H) 500 (typical) without touchscreen 800 x 480 262 K (supports 24-bit) 0.2168(H) x 0.
Appendix A TREK-303 Pin out for TREK-303 LVDS connector Table A.
Pin assignment P1 1 P2 1 2 2 3 3 4 4 5 6 5 6 7 7 8 8 9 9 10 11 12 10 11 12 Color Brown White Ground Brown red white Ground Ground Orange white red 13 13 14 15 14 15 16 16 17 17 18 18 Orange yellow white Ground Ground Green white 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Blue white Ground yellow Green Blue Black black Black Black Black Black Black Purple Grey white Black Orange Brown red Ye
Appendix A TREK-303 Figure A.1 Hotkey utility 1. 2. 3. 4. 5. 6. 7. Execute “Hot Key test” program → Brightness level: You may set a panel’s brightness from level 0 ~10, up to a total of 10 levels, when you finish setting the brightness level you want, please click “Apply”. If you want to check the current brightness level of TREK-303, please click “Get”.
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
