User Manual TPC-1071H/1271H/ 1571H/1771H Touch Panel Computer With Intel® Atom™ Dual Core Processor
Copyright The documentation and the software included with this product are copyrighted 2012 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. FCC Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Safety Instructions 1. 2. 3. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
TPC-1071H/1271H/1571H/1771H User Manual vi
Contents Chapter 1 General Information ............................1 1.1 1.2 Introduction ............................................................................................... 2 Packing List............................................................................................... 2 1.2.1 TPC-1071H and 1271H ................................................................ 2 1.2.2 TPC-1571H and 1771H ................................................................ 2 Specifications .........
Chapter 3 Features in Windows Embedded..... 45 3.1 3.2 3.3 Features in Windows Embedded ............................................................ 46 EWF ........................................................................................................ 46 HORM ..................................................................................................... 46 Appendix A A.1 Main Board Connector and Switch Settings47 A.2 A.3 Main Board Connector and switch Location and List...............
Chapter 1 1 General Information
1.1 Introduction The TPC-1071H/1271H/1571H/1771H Touch Panel Computers are state-of-the-art Human Machine Interfaces featuring 10"/ 12"/ 15"/ 17” displays with Intel Atom processors 400 and 500 Series with Intel ICH8M I/O Controller and the following key features: Fanless By using a low-power processor, the system does not have to rely on fans, which often are unreliable and causes dust to circulate inside the equipment.
1.3.1 System Kernel CPU: Intel® Atom™ D525 1.8GHz BIOS: AMI BIOS System Chipset: ICH8M VGA: Integrated in ICH8M Memory: 4GB SO-DIMM DDR3 SDRAM LAN: 10/100/1000Base-T x 2 Watchdog Timer: 1 ~ 255 sec (system) Expansion Slots: Half-size PCI-E x 1 or Full-size Mini PCI-E Storage: CompactFlash® slot and 2.5" SATA HDD x 1 1.3.2 I/O Ports TPC-1071H/1271H/1571H/1771H: 3 serial ports: RS-232 x 2 (w/ isolation), RS-422/485 x 1 (w / isolation) 1 PS/2 Keyboard/Mouse 2 USB 2.0 Ports: compliant with USB 2.
1.4 LCD Specifications TPC-1071H/1271H/1571H/1771H Display Type TFT LCD Size (diagonal) 10.4"/12.1”/15”/17” Maximum Resolution (Pixels) 800x600 (SVGA) / 800x600 (SVGA) / 1024x768 (XGA) / 1280x1024 (SXGA) Number of Colors 16.2M/ 16.2M/ 16.2M/ 16.7M Viewing Angle 160/140, 160/140, 160/140, 170/160 Luminance (cd / m2) 400/ 450/ 350/ 350 Contrast Ratio 700:1/ 700:1/ 700:1/ 1000:1 Backlight LED Note! There might be several bright or dark pixels on the LCD.
The arrangement of the I/O ports is shown in in Figure 1.1 and 1.2. Figure 1.2 TPC-1571H/1771H - I/O Port Arrangement (Antenna is optional. Use P/N:1750000318 to order) 5TPC-1071H/1271H/1571H/1771H User Manual General Information Figure 1.1 TPC-1071H/1271H - I/O Port Arrangement (Antenna is optional. Use P/N:1750000318 to order) Chapter 1 1.
1.8 Panel Mounting 1. 1. 2. 3. There is an adhesive waterproof gasket on the AL front bezel. Make sure the waterproof gasket is in position before installing TPC into the panel opening. Install the TPC into the panel opening. Find the eight clamps and eight long screws in the accessory pack. Hook the clamps to the holes around the four sides of the bezel. Insert the screws into every clamp and fasten them. These screws will push the mounting panel and fix the unit.
1.9.1 TPC-1071H 278.50 25 REF 72.3 3 227 214 287 Figure 1.5 TPC-1071H Dimensions 7TPC-1071H/1271H/1571H/1771H User Manual General Information 160.1 Weight: 3kg Dimensions (W x H x D): – 287.0 ±0.5x 227.0±0.5 x 72.3±1.0 mm(11.29" x 8.94" x 2.84") Cutout: – 279.5±0.5x219.5±0.5mm 218.50 Chapter 1 1.
1.9.2 TPC-1271H Weight: 4.57kg Dimensions (W x H x D): – 311.0 ±0.5x 237.0±0.5 x 73.1±1.0 mm (12.24" x 9.33" x 2.88") Cutout: 302.0±0.5 x 228.0 ±0.5mm 20.6 3 73.1 25 REF 301 227 237 247 311 185.50 Figure 1.
24.5 1.27 373 78.50 4.5 383 306.1 307 Figure 1.7 TPC-1571H Dimensions 9TPC-1071H/1271H/1571H/1771H User Manual General Information 230.1 Weight: 5.5kg Dimensions (W x H x D): – 383.0±0.7 x 307.0±0.7 x 78.5±1.5 mm (15.08" x 12.09" x 3.09") Cutout: 374.5 ±0.7x 298.5±0.7 mm 297 Chapter 1 1.9.
1.9.4 TPC-1771H Weight: 6kg Dimensions (W x H x D): – 414±1 x 347.5±1 x 84±1.5 (16.3" x 13.68" x 3.31") Cutout: 400.8±1 x 334.3 ±1 7 84 ±1.5 25 REF 399.20 332.70 347.50 ±1 90 210 10.5 30 8-M4x4L 120 340 240 272.50 414 ±1 7 TYP Figure 1.
Chapter 2 System Setup 2
2.1 System Setup You can easily get TPC started by following the below steps. 1. Unpack the TPC package. Check the packing list at the beginning of this manual to make sure all items have been included. Figure 2.1 Unpack the Package 2. Install a CompactFlash card containing Windows CE, Embedded Windows XP or another operating system.
Chapter 2 Warning! It is suggested to turn OFF system power as you plug in or pull out the memory card, even though the CompactFlash memory is hot swappable. 3. Connect the power connector to the 24 VDC power lines. The power lines can either be of some power adapter or in-house power source. Figure 2.3 Pin Definition of Power Connector 13 TPC-1071H/1271H/1571H/1771H User Manu- System Setup Figure 2.
Figure 2.4 Power Receptor & Switch Pin Assignment 4. 5. 6. Plug the power lines into the system power receptor. Power on the system. Calibrate the touchscreen (click "PM" in the bottom corner). Note! If you want to install the touchscreen driver & use the touchscreen utility, please refer the user manual which is “PenMount 6000 InstallationGuide” on the DVD.
Note! Audio driver will only be installed if you purchase TPC-1x71H series with audio function (Option). Note! You can download the latest driver on the Advantech support portal of Advantech’s website if there is any updated.
2.2.1 Installation of Touch Screen driver 1. Enter into TS folder, enter into PenMount Universal Driver folder and double click setup icon, and then click “Next” under setup wizard window. 2.
Click “Install” 4. Click “Finish” to finish the installation 5. After installing Touch Screen driver, a “PenMount Monitor” icon will show on your notification area. Chapter 2 3.
2.2.2 Installation of DIO driver 1. Enter into DIO folder, double click Advantech UNODIO WDM Driver icon, and then click “Next” under InstallShield Wizard window 2.
4. Click “Next” 5. Click “Next” System Setup Click “Next” Chapter 2 3.
6. Click “Finish” to finish the installation. 7. After installing DIO driver, a “Advantech UNODIO WDM driver” icon will show in control panel.
Double click the “Advantech UNODIO WDM driver” icon, a UNODIO driver Configuration will show the DIO function of TPC-1x71H series which contains 8 DI, 2 DI interrupt, 8 DO and a buzzer function. Chapter 2 8.
2.2.3 Installation of SRAM driver 1. Step 1.Enter into SRAM folder, double click AdvPCISRamDisk icon, and then click “Next” under InstallShield Wizard window. 2.
Click “Install” 4. Click “Finish” to finish the installation 5. Select “Yes, I want to restart my computer now” and click “OK” Chapter 2 3.
6. After installing SRAM driver, a ADV-SRAM drive will exist in your computer 7. After installing TS, DIO and SRAM driver, there is no any question mark in device manger.
Enter into Watchdog folder, double click AdvWDT icon, and then click “Next” under InstallShield Wizard window 2. Select “Advantech [SCH311X] WDT” and click “Next” System Setup 1. Chapter 2 2.2.
3. Click “Install” 4. Click “Finish” to finish the installation 5.
7. Double click the “Watchdog Service Configuration” icon, and you can configure the Watchdog timer function. System Setup After installing Watchdog driver, a “Watchdog Service Configuration” icon will show in control panel Chapter 2 6.
2.3 Touch Screen configuration PenMount Monitor icon (PM) appears in the notification area of Windows XP system when you turn on PenMount Monitor in PenMount utility. PenMount Monitor has the following functions: 1. Control Panel Open PenMount Control Panel 2. Beep Setting Beep function for each device. 3. Right Button When you select this function, a mouse icon appears in the right-bottom of the screen. Click this icon to switch between Right and Left Button functions. 4.
Chapter 2 Right-click on the PenMount Monitor icon in the notification area and select Control Panel from the menu. You will see Device, Multiple Monitors, Tools and About tabs which will introduce their function in this section. System Setup 2.3.1 Device You will see the icon of PenMount 6000 RS232 under Device tab. In Device tab, you can see the devices detected on your system. Select a device and press the Configure button to configure it.
Then, you will see some tabs such as Calibrate, Setting, Edge Compensation, and About of the device you selected. 2.3.1.1 Calibrate This function offers two ways to calibrate your touchscreen. 'Standard Calibration' adjusts most touchscreens while 'Advanced Calibration' adjusts aging touchscreens. You can select either or both method to calibrate your touchscreens.
Standard Calibration: Click this button and arrows appear pointing to red squares. Use your finger or stylus to touch the red squares in sequence. After the fifth red point calibration is complete. To skip, press 'ESC'. 2. Advanced Calibration: Advanced Calibration uses 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touchscreens. Click this button and touch the red squares in sequence with a stylus. To skip, press 'ESC'. Note! 3. 4.
2.3.1.2 Setting 1. Operation Mode: This mode enables and disables mouse's ability of dragging on-screen icons-useful for configuring POS terminals. – Pen Input Emulation: Select this mode and mouse will emulate Windows Vista pen input device operation, by which no mouse event will be sent until the touch is dragged out of range or released from the screen. – Click on Touch: Select this mode and mouse only provides a click function, and dragging is disabled.
Chapter 2 2.3.1.3 Edge Compensation System Setup Edge compensation is used to optimize the cursor accuracy on the edge, which is for advanced calibration. You can adjust the settings from 0 to 30 for accommodating the difference of each touch panel. 2.3.1.
2.3.2 Multiple Monitors Multiple Monitors supports two to six touchscreen displays for one system. However TPC-1x71H series only provides one touchscreen display so this function is not workable on TPC-1x71H series. 2.3.2.1 Tools In Tools tab, there are Draw, Right Button Icon, Gesture Enable, and Gesture Setting function. They will be introduced in this section. 2.3.2.2 Draw Draw function is used to test or demonstrate the PenMount touchscreen operation.
Show Grid: Show grid on the entire monitor. This is for linearity test. 2. Show Pen Location: Show the locations where pen comes down and lifted up on the monitor. Clear Screen: Clear drawing Exit: Quit draw function 3. 4. 2.3.2.3 Right Button Icon Right Button function simulates the right button function of a mouse. Click the right button and you can only touch the screen once and the driver changes the touch definition to the left button.
2.3.2.4 Gesture Enable Enable/configure Gesture AP to support PenMount gestures recognition. You can enable or disable it in the following two ways. In the notification, right-click on the PenMount icon and select Gesture Enable from the menu. A PenMount Gesture AP icon will show up in the notification area. See the illustration below. PenMount Gesture AP is running. 5. In PenMount Control Panel, select Tools tab and press Gesture Enable button. PenMount Gesture AP icon shows up in the notification area.
Chapter 2 2.3.2.4.1Gesture Setting Right-click on the PenMount Gesture AP icon in the notification area, select Gesture Setting from the menu that appears or select Tools tab and press Gesture Setting button in PenMount Control Panel. System Setup Then, the Gesture Setting window will show the following information, and you can proceed to configure PenMount Gesture AP.
Part A: Enable/disable Check Box. Select/deselect the box to enable/disable PenMount Gestures. Part B: General Setting Sensing Time: Move the slider to adjust PenMount Gestures Sensing Time between 200 ms (0.2 sec) and 2500 (2.5 sec). The shorter the sensing time is configured, the faster the gesture has to be done. Part C: Gesture Setting C1 Disable Button: When this button is selected, the gesture is disabled. C2 Hot-key Configure Button: Configure the hot-keystrokes for specific gesture.
TPC-1x71H series has four wake-up modes which can let you do versatile setting such as remote control. You can wake up the system on USB, LAN, touch screen and PS/2. The following table shows each wake-up mode in detail. Wake up from Note! S5 V V V S3: Sleep state where all system context is lost except system memory. OS context is maintained within the memory and is not reloaded at startup. S5: This sleep state looks very much like S4 with the exception of the fact that the OS context is not stored off.
2. In General tab, select “Configure” button. 3. In Power Management tab, check “Allow this device to bring the computer out of standby” to enable the Wake-on-LAN function.
If you need wake-on-touch screen function, you need to enable the function in BIOS. Touch screen can wake up the system from S3 and S5. 1. Enter into BIOS setup utility. Chapter 2 2.4.2 Wake-on-Touch Screen System Setup 2. Enter into Advanced tab and select ACPI Configuration.
3. Select Chipset ACPI Configuration. 4. Enable Resume On Touch function. 2.4.3 Wake-on-USB If you need wake-on-USB function, you need to enable the function in BIOS. USB can wake up the system from S3. 1. Enter into BIOS setup utility. 2. Enter into Advanced tab and select ACPI Configuration. 3. Select Chipset ACPI Configuration. 4. Enable USB Device Wakeup From S3.
While the system enters into S3 mode, clicking left- or right-button of the mouse, moving the mouse or pressing any key of keyboard can wake the system up and entering into OS. 2.5 Cabinet Installation Guide 1. Embed TPC-1x71H series into the cabinet. Step A: Connect the cabinet to earth ground. Step B: Embed null TPC-1x71H series into the cabinet without any I/O cable and power.
2. System wiring Step A: Connect the cabinet to earth ground. Step B: Ensure that all cabinet has been grounded together. Step C: Connect the ground of the power supply to the cabinet. Step D: Connect the ground pin of TPC-1x71H series to the cabinet. Step E: Connect the I/O to the controller if needed. Step F: Connect the V+ and V- of power supply to TPC-1x71H series. While completing step A to F step by step, you can supply power to TPC-1x71H series now.
Chapter 3 3 Features in Windows Embedded
3.1 Features in Windows Embedded TPC product supports the embedded Windows platform. This section outlines the important features (EWF and HORM), that are provided in Windows embedded. 3.2 EWF EWF stands for Enhanced Write Filter. It provides an upper filter in the storage device driver stack that redirects disk write operations to volatile (RAM) or non-volatile (disk) storage. EWF protects a volume from write access. The benefits are as the following. Write-protect one or more partitions on your system.
Appendix A A Main Board Connector and Switch Settings
A.1 Main Board Connector and switch Location and List Figure A.1 Jumper and Switch Locations Reference Function CN9 mPCIe Description Expansion mPCIe card slot CN15 PCIe Expansion PCIeX1 card slot CN16 (Option) VGA Internal VGA connector, along with VGA cable (P/N: 1700018870) CN17 (Option) Serial port COM5: Internal COM connector, along with COM cable RS-232 (P/N: 1700002383) CN18 (Option) USB2.0 Internal USB connector, along with USB cable (P/N: 1700018869) CN19 (Option) USB2.
Serial port COM2: RS-232 D-Sub 9 pin male with isolation CN28 Serial port COM1: RS-232 D-Sub 9 pin male with isolation CN30 CF Compact flash socket PCN1 DC IN DC Power in Connector SW5 Termination resistor switch Select termination resistor for RS-422/485 of COM6 SW6 Termination resistor switch Select termination resistor for RS-422/485 of COM3 A.
A.3 Serial Port Settings TPC-1x71 series has 3 RS-232 serial ports (2 external ports with isolation and 1 internal port without isolation) and 2 RS-422/485 serial ports (1 external port with isolation and 1 internal port without isolation) which are: RS-232 RS-422/485 External (w/ isolation) COM1, COM2 COM3 Internal (Option) (w/o isolation) COM5 COM6 The connector location is shown in the following figure.
A.3.1.1 Pin Definition Pin 1 2 3 4 5 6 7 8 9 Signal NDCD NRX NTX NDTR GND NDSR NRTS NCTS NRI 51 TPC-1071H/1271H/1571H/1771H User Manu- Appendix A Main Board Connector and Switch Settings A.3.
A.3.2 COM3/ COM6(Option): RS-422/ 485 The serial port COM3 and COM6(Option) on the TPC-1x71H series are adjustable by BIOS. It can be set to RS-422 or RS-485 mode. This port is designed with auto data flow control capability. In other word, the TPC-1x71H series can automatically detect the data flow direction at this port when the two wired RS-485 communication is activated. A.3.2.1 Pin Definition Pin 1 2 3 4 5 6 7 8 9 Signal RS-422 TXTX+ RXRX+ GND - RS-485 DD+ GND - A.3.2.
Enter into Advanced tab and select SuperIO Configuration 3. Select Serial Port3 Mode (COM3) for RS-422/ 485 mode setting. Also, select Serial Port6 Mode (COM6) for RS-422/ 485 mode setting. The default setting is RS-422 mode. 53 TPC-1071H/1271H/1571H/1771H User Manu- Appendix A Main Board Connector and Switch Settings 2.
TPC-1071H/1271H/1571H/1771H User Manual 54
Appendix B B Built-in DIO Module Setting
The TPC-1071H/1271H/1571H/1771H contains a built-in DIO module which provides 8 digital input and 8 digital output channels with 2500 Vrms isolation protection, 2 digital input channels with interrupt function and a programmable buzzer function. For more detail DIO fuction, please install DIO driver in DVD and you can get example code and user’s manual in the following path: C:\Program Files\Advantech\UNODIO. B.
B.3.1 Pin Assignment B.3.2 Wiring Isolated digital input – Dry contact Isolated digital input – Wet contact Isolated digital output 57 TPC-1071H/1271H/1571H/1771H User Manu- Appendix B Built-in DIO Module Setting B.
B.4 Introduction of DIO utility This section will introduce you how to use DIO example (DI, DI interrupt, DO and buzzer), and you can access DIO example at the following path: C:\Program Files\Advantech\UNODIO\Examples\VB. For more detail information , please refer to Advantech UNODIO WDM Driver User Manual located at: C:\Program Files\Advantech\UNODIO\Manual. B.4.1 Digital input utility The digital input utility can be accessed in the following path: C:\Program Files\Advantech\UNODIO\Examples\VB\DIGIN 1.
The digital input interrupt utility can be accessed in the following path: C:\Program Files\Advantech\UNODIO\Examples\VB\DIINT. 1. 2. 3. 4. Click “Start”. The application will read the DI port value, according to the userspecified clock source, and then display the current DI port value. The eight signal lamps correspond to the eight bits of DI port. Click "Enable". The application will enable an event as specified by the user and track the event as well as displays its frequency.
B.4.4 Buzzer utility The buzzer utility can be accessed in the following path: C:\Documents and Settings\TPC1x71H\Desktop\DIO\Buzzer. 1. 2. 3. There are four beep mode to select. Select one mode and click “OK” to execute the buzzer. If you want to stop the buzzer, please select BEEP_DISABLE mode.
Embedded Platform PCI Digital I/O Base Address 0 R/W BIT7 BIT6 BIT5 BIT4 Base Address 0 + 00H ~ 1EH Base Address 0 + 1FH BIT3 BIT2 BIT1 BIT0 D1 D0 Reserved FPGA Code Revision R D7 D6 D5 D4 D3 D2 Embedded Platform PCI Digital I/O Base Address 1 R/W BIT7 R Base Address 1 + 00H BIT6 BIT5 BIT4 Base Address 1 + 01H W R Base Address 1 + 02H W R Base Address 1 + 03H W Base Address 1 + 04H~06H BIT2 BIT1 BIT0 DI DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 DO2 DO1 DO0 DO2 DO1 DO0 DI
B.4.5.1 Interrupt Enable/Disable Control (Base Address 1 + 02H) DI0EN / DI1EN Interrupt Control 0 1 Disable Enable B.4.5.2 Interrupt Triggering Edge Control (Base Address 1 + 03H) DI0RF / DI1RF Triggering Edge of Interrupt Signal 0 1 Falling edge trigger Rising edge trigger B.4.5.3 Interrupt Flag Control (Base Address 1 + 07H) DI0IF / DI1IF Interrupt Flag Status 0 1 No interrupt Interrupt occur DI0IFCLR / DI1IFCLR Interrupt Flag Clear Register 0 1 Don't care Clear interrupt B.4.5.
1. Find DIO driver folder under TPC-1x71H series folder in driver support DVD as follows: 2. Double click “Advantech UNODIO WDM Driver V2.08 Build 001.exe” to start installation: 3. After installation completes, if you need software operation support, find the Manual folder in the default installation path. 63 TPC-1071H/1271H/1571H/1771H User Manu- Appendix B Built-in DIO Module Setting B.4.
TPC-1071H/1271H/1571H/1771H User Manual 64
Appendix C HDD assembly instructions C
C.1 HDD Assembly Instructions Follow the assembly procedure to install the HDD into the system. 1. Remove side cover 2. Figure C.1 Removing the side cover And then loosen six screws to remove HDD bracket shown in below Figure C.
Install 2.5" HDD into the HDD holder with four screws fixed 4. Figure C.3 Installing HDD in the holder Connect HDD to the HDD cable connector Figure C.4 Connecting the HDD cable 67 TPC-1071H/1271H/1571H/1771H User Manu- Appendix C HDD assembly instructions 3.
5. Put HDD bracket in top of HDD holder and fix with the holder together by screws 6. Figure C.5 Fixing the HDD bracket with holder Place the side cover back to the position Figure C.
1. Remove the screws which are circled and pull the access cover. 2. Remove the screw which is circled. 69 TPC-1071H/1271H/1571H/1771H User Manu- Appendix C HDD assembly instructions C.
3. Pull the PCIe bracket out.
Insert the PCIe card into PCIe slot of TPC-1x71 series. The boundary of PCIe card can embed in the PCIe guide rail. 71 TPC-1071H/1271H/1571H/1771H User Manu- Appendix C HDD assembly instructions 4.
C.3 Installation guide of expansion mPCIe 1. Remove the screws which are circled and pull the access cover. 2. Remove the screws which are circled.
Remove the HDD cover. 4. Insert mPCIe card into mPCIe slot. If you need to install an antenna, there is an extension cable attached nearby. 73 TPC-1071H/1271H/1571H/1771H User Manu- Appendix C HDD assembly instructions 3.
TPC-1071H/1271H/1571H/1771H User Manual 74
Appendix D D WatchDog Installation Guide
The Watchdog WDM Driver allows you to easily perform versatile WDT operations through properties, methods and events in programs developed with Microsoft Visual C++ and Microsoft Visual Basic. After you complete to install the Watchdog driver, you can access Watchdog Service Configuration utility in control panel.
2. 3. 4. 5. 6. You can select one timer span for the Watchdog and apply the changes when the Watchdog is disabled, there are 6 timer span arranges from 15 seconds to 4 minutes 15 seconds available. Watch Mode radio box group: There are two watch modes, system watch mode and application watch mode.
In the About tab, there shows some copyright information of the Advantech Watchdog service.
Appendix D WatchDog Installation Guide 79 TPC-1071H/1271H/1571H/1771H User Manu-
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
