PPC-S154T UltraSlim™ Mobile Intel® Pentium® 4 processor-M based 15" panel PC User’s Manual
Copyright This document is copyrighted, © 2003. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • PPC-154T series panel PC • User's manual (note 1) • Accessories for PPC-154T - Y-shaped adapter for PS/2 mouse and keyboard - Warranty card - Power cord: USA type - AC/DC power adapter - Floppy disk with CD-ROM drive driver -"Drivers and Utilities" CD-ROM disc -VESA-standard bracket for mounting - Mounting kits and packet of screws - Heat sink (note 1) - Heat sink support plate kits (note 2
Additional Information and Assistance Step 1. Visit the Advantech web site at www.advantech.com or www.advantech.com.tw where you can find the latest information about the product. Step 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
DISCLAIMER: This set of instructions is given according to IEC704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
CONTENTS Chapter 1 General Information ........................................2 1.1 1.2 1.3 1.4 Introduction ....................................................................... 2 General Specifications....................................................... 3 LCD Specifications ........................................................... 6 Dimensions........................................................................ 6 Figure 1.1:Dimensions of PPC-154T..............................
4.1.3 4.1.4 Installing the 2.5" Hard Disk Drive (HDD).................. 26 Table 4.2:Panel PC connectors ..................................... 26 Locating connectors...................................................... 27 Figure 4.2:Locating connectors on the PPC-S154T motherboard .............................................. 27 4.2 4.3 CPU Installation .............................................................. 27 CMOS Clear for External RTC (JP3) ............................. 28 4.
8.2 Chapter Installation of Audio Driver ............................................ 46 9 USB 2.0 ............................................................48 9.1 Installation of USB 2.0 driver ......................................... 48 Chapter 10 Touchscreen ....................................................50 10.1 Introduction ..................................................................... 50 10.1.1 General information...................................................... 50 10.1.
Table B.14:COM1 ........................................................ 70 B.15 14 VGA connector (CN2) ............................................... 71 B.16 Parallel Port Connector (CN8)(Reserved)....................... 71 B.17 TV OUT (S-VIDEO) connector (Reserved)(CN6) ......... 72 Table B.15:VGA connector (CN2)............................... 71 Table B.16:Parallel Port Connector (CN8)................... 71 Table B.17:TV OUT (S-VIDEO) connector (Reserved)(CN6) ....................................
CHAPTER 1 General Information This chapter gives background information on the PPC-S154T panel PC.
Chapter 1 General Information 1.1 Introduction PPC-S154T panel PC is a mobile Pentium® 4-M processor-based UltraSlim panel computer that is designed to serve as a human machine interface (HMI) and multimedia computer. It is a PC-based system with 15” color TFT LCD display, on-board PCI Ethernet controller, multiCOM port interfaces and an 18-bit stereo audio controller.
1.2 General Specifications General • Dimensions (W x H x D): 375 x 299 x 49 mm (14.76" x 11.77" x 1.39") • Weight: 4.9 kg (10.78 lb) • Power supply: 70 watts, ATX type Input Voltage: 16Vdc~25Vdc Onput Voltage : +5 V @ 12 A,+24 V @ 0.3 A • Power adaptor: AC/DC Input voltage: 100 ~ 240 VAC Output voltage: 19 V@ 3.79 A • Disk drive housing: Space for one 2.5" HDD, One slim type CD-ROM and one slim type 3.
• Serial ports: Two serial ports with one RS-232 ports (COM 1), one RS-232/422/485 port (COM2). All ports are compatible with 16C550 UARTs, +5V/+12V power supply selectable • Universal serial bus (USB) port: Supports up to two USB ports, Intel UHCI v2.
Touchscreen (Optional) Type Analog Resistive Resolution Continuous Light Transmission 75% Controller RS232 interface (uses COM4) Power Consumption <5 V@ 100 mA Software Driver Supports Windows 98/2000/ME/ XP Optional modules • CPU: Support Intel® Pentium® 4-M up to 2.2 GHz • Memory: 128/256/512 MB DDR 266 SDRAM • HDD: 2.
1.3 LCD Specifications • Display type: 15” TFT LCD • Max. resolution: 1024 x 768 • Colors: 16.7 M • Dot size (mm): 0.297 x 0.297 • Viewing angle: 120° (minimum) • Luminance: 200 cd/m2 • Temperature: 0 ~ 50° C • *VR control: Brightness • LCD MTBF: 50,000 hours • Backlight lifetime: 25,000 hours * The VR control is defined by hot key in DOS or BIOS mode as below: Ctrl-Alt-F3, Ctrl-Alt-F4. Note: The color LCD display installed in the panel PC is high-quality and reliable.
CHAPTER 2 System Setup This chapter details system setup on the PPC-S154T panel PC.
Chapter 2 System Setup 2.1 A Quick Tour of the Panel PC Before you start to set up the panel PC, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below. When you place the panel PC upright on the desktop, its front panel appears as shown in Figure 2-1. 5 4 2 3 1 Figure 2.
When you look at the left side of the panel PC, you will see the floppy disk drive, CD-ROM drive and PCMCIA expansion sockets, as shown in Fig. 2-2. Compact CD-ROM drive CD-ROM eject button CD-ROM drive activity light • • • FDD eject button FDD slot • • FDD activity light • Figure 2.2: Left side view of the panel PC When you turn the panel PC around and look at its rear cover, you will find the CPU and heat sink space located on the left-top side.
CPU and Heatsink cover • HDD bracket • • • • Product label Figure 2.3: Rear view of the panel PC DC inlet COM1 USB ports PS2 port Line-out jack COM2 VGA port Ethernet Mic-in Line-in Jack jack jack Figure 2.4: Rear and bottom view of the panel PC Figure 2-4 shows the I/O section and power switch of the panel PC.
2.2 Installation Procedures 2.2.1 Connecting the power cord The panel PC can only be powered by a DC electrical outlet (16Vdc~25Vdc, 3.5A max.). Be sure to always handle the power cords by holding the plug ends only. Please follow the figure 2-5 to connect the male plug of the power cord to the DC inlet of the panel PC. 2.2.
Power switch (Lock status) Figure 2.6: Power switch in lock status Power switch (Open status) Figure 2.
2.3 Running the BIOS Setup Program Your panel PC is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the panel PC's BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of hard drive. The setup program is stored in read-only memory (ROM).
2.4 Installing System Software Recent releases of operating systems from major vendors include setup programs which load automatically and guide you through hard disk preparation and operating system installation. The guidelines below will help you determine the steps necessary to install your operating system on the panel PC hard drive. Note: Some distributors and system integrators may have already pre-installed system software prior to shipment of your panel PC.
2.5 Installing the Drivers After installing your system software, you will be able to set up the Ethernet, SVGA, audio, and touchscreen functions. All the drivers except the CD-ROM drive driver are stored in a CD-ROM disc entitled "Drivers and Utilities." The CD-ROM drive driver is stored in a floppy disk. Both the CD-ROM and the floppy disk can be found in your accessory box.
PPC-S154T User’s Manual 16
CHAPTER 3 Hardware and Peripheral Installation This chapter details the installation of the PPC-S154T panel PC hardware. Sections include: • Overview of Hardware Installation and Upgrading • Installing the 2.
Chapter 3 Hardware and Peripheral Installation 3.1 Overview of Hardware Installation and Upgrading The panel PC consists of a PC-based computer that is housed in a plastic front and rear panel. Any maintenance or hardware upgrades can be completed after removing both panels. Meanwhile your HDD, SDRAM, CPU are all readily accessible by removing the CPU and heatsink cover and HDD bracket.. Warning! Do not remove the plastic covers until you have verified that no power is flowing within the panel PC.
4. Put the HDD bracket with HDD back to original position, then screw the four screws to fix it. Figure 3.1: Install the HDD on the HDD bracke t Figure 3.
3.3 Installing the SDRAM Memory Module and Central Processing Unit (CPU) The panel PC's central processing unit (CPU) can be upgaded to improve system performnace. The panel PC provides one 478-pin ZIF (Zero Insertion Force) socket (Socket 478). The CPU must come with an attached heat sink and CPU fan to prevent overheating.
2. Locate the ZIF socket and open it by first pulling the lever side ways away from the socket, then upwards at an angle of 90 degrees. 3. Insert the CPU with the correct orientation 4. Slide the CPU in gently. It should insert easily. If not, pull the lever up a little more and make sure the pins of the CPU correspond with the holes of the socket. DO NOT USE EXCESSIVE FORCE! 5. Press the lever down. The plate will slide across slightly. 6.
10. Finally, put the heatsink with the fan back and tighten the four screws, then put back and fix the plasticcover.
CHAPTER 4 Jumper Settings and Connectors This chapter tells how to set up the panel PC hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installation procedures.
Chapter 4 Jumper Settings and Connectors 4.1 Setting jumpers You can configure your panel PC to match the needs of your application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To ìcloseî a jumper, you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
4.1.1 Jumpers and switch The motherboard of the panel PC has a number of jumpers that allow you to configure your system to suit your applications. The table below lists the function of each of the boardís jumpers. Table 4.1: Jumpers and their functions Label Function JP2 LCD power connector JP3 CMOS clear for external RTC JP4 COM2 RS232/422/485 setting JP5 COM1 / COM2/ COM3 ping 9 output type setting SW1 Panel type setting 4.1.2 Locating jumpers and switch SW1 JP2 JP3 JP4 JP5 Figure 4.
4.1.3 Installing the 2.5" Hard Disk Drive (HDD) Onboard connectors link the panel PC to external devices such as hard disk drives or floppy drives. The table below lists the function of each of the board ís connectors. Table 4.
4.1.4 Locating connectors Fan1 DIMM 1 CN6 DIMM 2 CN3 CN4 CN19 CN18 FAN2 CN26 CN13 CN4 CN9 CN7 CN25 CN8 CN16 CN11 CN12 Figure 4.2: Locating connectors on the PPC-S154T motherboard 4.2 CPU Installation You can install an Intel® Pentium®-M CPU without setting any frequency ratio or voltage.
4.3 CMOS Clear for External RTC (JP3) Warning: To avoid damaging the computer, always turn off the power supply before setting “Clear CMOS”. Set the jumper back to ìNormal operationî before turning on the power supply. Table 4.3: Clear CMOS / External RTC (JP3) *Normal operation 1 2 Clear CMOS 3 1 2 3 * default setting 4.4 COM-port Interface The panel PC provides two serial ports,COM1 : RS-232, COM2:RS-232/ 422/485 (in one COM port connector) 4.4.
Table 4.5: COM2 RS-232/422/485 setting (JP4) RS-422 2 6 10 14 18 1 5 9 13 17 * default setting Table 4.6: COM2 RS-232/422/485 setting (J4) RS-485 2 6 10 14 18 1 5 9 13 17 * default setting The IRQ and the address ranges for COM1 and 2 are fixed. However, if you wish to disable the port or change these parameters later you can do this in the system BIOS setup. The table overleaf shows the default settings for the panel PCís serial ports. COM1 and COM2 are one set.
4.4.2 COM1/COM2/COM3/ pin 9 output setting (JP5) Table 4.8: COM1/2/3 pin 9 output setting(JP5) *Normal +5 V output +12 V output *Default setting NOTE: Pins 3,5 are for COM1 Pins 4,6 are for COM2 Pins 9,11 are for COM3 4.5 VGA Interface The panel PC's AGP VGA interface can drive conventional CRT displays. It is also capable of driving a wide range of flat panel displays, including electroluminescent (EL), gas plasma, passive LCD and active LCD displays.
4.5.1 LCD panel power setting The panel PC's AGP SVGA interface supports 5 V and 3.3 V LCD displays. The LCD cable already has a built-in default setting. You do not need to adjust any jumper or switch to select the panel power. 4.5.2 Panel type select (SW1) SW1 is a 8-pin dip switch for selecting panel type and display mode. A 1024 x 768 TFT LCD is used in the PPC-S154T, so the switch is preset according to the table below.
PPC-S154T User’s Manual 32
CHAPTER 5 Intel Chipset This chapter provides information on Intel chipset configuration • Introduction • Installation of Intel INF driver -Installation of Intel IAA driver • Further information
Chapter 5 Intel Chipset 5.1 Introduction The PPC-S154T uses the combination of Intel 845GV north bridge and Intel 82801 DB ICH4 south bridge. The Intel® 845GV chipset is an innovative integrated graphics chipset developed with DDR266 memory and optimized to support the Intel Pentium® 4/ Pentium® 4-M processor, adding intelligence to help manage and prioritize multiple threads received from the microprocessor.
1. Path: D:\PPC-S154\Chipset Software\IAA Drivers\2.3\iaa23_multi 2. Press "Next "to proceed, and press "Finish". 3. Choose "Yes, I want to restart my computer", and press "Finish", the system will reboot automatally 5.2 Further Information Intel website: http://www.intel.com Advantech websites: www.advantech.com www.advantech.com.
PPC-S154T User’s Manual 36
CHAPTER 6 AGP SVGA Setup • Introduction • Installation of SVGA Driver - for Windows 98 - for Windows 2000/XP • Further Information
Chapter 6 AGP SVGA Setup 6.1 Introduction The PPC-S154T has an on board integrated VGA chipset The specifications and features are described as follows: 6.1.1 Chipset The PPC-S154T uses a integrated graphics chipset in Intel 845GV chipset . The Intel 845GV chipset contains an entirely new 32bpp graphics hardware engine, known as Intel Extreme Graphics, which has been designed and built by Intel to optimize the performance of the Intel Processor.
6.2.1 Installation for Windows 98 1. Click the 'Start' button in the task bar, click 'Run' and then select 'Setup.exe' from D:\PPC-S154\845G Graphics Driver\WIN9X_ME\Setup.exe. The Install dialog will appear. 2. click 'Next' to continue. 3. Read License Agreement and click "Yes" to proceed. 4. When the 'Setup COMPLETE' message appears click 'Finish' to restart PPC-S154T. 5. After the system reboot, the screen show "Insert Disk", click "OK" 6. click "browse" 7.
6.3 Further Information For further information about the AGP/SVGA installation in your PPCS154T, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: Intel support website: http://downloadfinder.intel.com Advantech websites:www.advantech.com www.advantech.com.
CHAPTER 7 PCI Bus Ethernet Interface This chapter provides information on Ethernet configuration.
Chapter 7 PCI Bus Ethernet Interface 7.1 Introduction The PPC-S15T4 is equipped with a high performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T and 10Base-T compatible. The Ethernet port provides a standard RJ-45 jack. The network boot feature can be utilized by incorporating the boot ROM image files for the appropriate network operating system.
7.2.1 Installation for Windows 98/NT/ME/2000 Upon installing on Windows 98, the system will automatically detect the Ethernet hardware and install the Ethernet driver. It is recommended that you upgrade to the Intel driver as following : 1. a Select "Start", "Settings", "Control Panel", "System" b. Click "Device Manager" and highlight "PCI Ethernet Controller" c. Select "Properties" 2. Choose "Driver" folder 3. Click "Update Driver" 4. a. Follow the instructions b. Click "Next" 5.
7.3 Further Information Intel website : - Main Intel web support site: http://support.intel.com - Network products information: http://www.intel.com/network Advantech websites: www.advantech.com www.advantech.com.
CHAPTER 8 2 Audio • Introduction • Installation of Audio Driver
Chapter 8 Audio 8.1 Introduction The ALC202 is an 18-bit, full duplex AC'97 2.2 compatible stereo audio CODEC designed for PC multimedia systems, including host/soft audio and AMR/CNR based designs. The ALC202 AC'97 CODEC supports multiple CODEC extensions with independent variable sampling rates and built-in 3D effects. 8.2 Installation of Audio Driver Before installing the audio driver, please take note of the procedures detailed below.
CHAPTER 9 USB 2.0 This chapter describes how to install USB 2.
Chapter 9 USB 2.0 9.1 Installation of USB 2.0 driver Before installing the audio driver, please take note of the procedures detailed below. You must know which operating system you are using in your PPC-S154T, and then refer to the corresponding installation procedure Important : The following windows illustrations are examples only. You must follow the instructions and pay attention to the instructions which then appear on your screen. Note: The CD-ROM drive is designated as "D" throughout ths chapter.
CHAPTER 10 Touchscreen • Introduction • Installation of Touchscreen Drivers - for Windows 98/ME - for Windows 2000/XP
Chapter 10 Touchscreen 10.1 Introduction 10.1.1 General information The PPC-S154T's optional touchscreen incorporates advanced secondgeneration resistive, impact-resistant technology. It allows 75% light transmission. The resistive model has an antiglare surface. This model provides greatly enhanced visual resolution. It also has new improved scratch-resistant features. The touchscreen is manufactured from UL-recognized components.
- Methyl ethyl ketone - Isopropyl alcohol - Hexane - Ammonia-based glass cleaners - Turpentine - Mineral spirits - Foods and beverages 10.2 Installation of Touchscreen Drivers The touchscreen driver for Windows contains a native, 32-bit driver and a 32-bit control panel program for the PPC-S154T system. To facilitate installation of the touchscreen driver, you should read the instructions in this section carefully before you attempt installation. Important: The following are examples only.
2. Select from "D:\PPC-S154\TouchScreen\Windows 98-Me Driver V3.1\setup.exe" to install PenMount windows 98/ME driver to system 3. The screen display PenMount logo, copying "installation wizard" and "PenMount Utilities" screen plus "welcome" message appears. Selete "Next" 4. The next screens is "Software License Agreement", select "Yes" 5. The next screens is "Information", select "Next" 6. The next screen is "Choose Destination Location".
5. The next screen is "Hardware Installation" , select " Continue Anyway" 6. The next screen is "InstallShield Wizard Completed", Select "Finish" 10.3 Further Information Dynapro website: www.dynapro.com www.3m.com/us/electronics_mfg/touch_systems Advantech websites: www.advantech.com www.advantech.com.tw Salt website: www.salt.com.
PPC-S154T User’s Manual 54
Appendix A Programming the Watchdog Timer The PPC-S154T is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environments.
Appendix A Programming the Watchdog Timer A.1 Programming the Watchdog Timer To program the watchdog timer, you must write a program which writes I/ O port address 440 (hex). The output data is a time interval value. The value range is from 01 (hex) to 3F (hex), and the related time interval is from 1 sec. to 63 sec. Data Time Interval 01 1 sec. 02 2 sec. 03 3 sec. 04 4 sec. ï ï ï ï ï ï 3F 63 sec.
;----------------------------------------------------------------------------; Configurate logical device 8, configuration register CRF6 | ;----------------------------------------------------------------------------MOV DX,2EH MOV AL,07H ; point to Logical Device Number Reg.
OUT DX,AL ;-----------------------------------------; Exit extended function mode | ;-----------------------------------------MOV DX,2EH MOV AL,AAH PPC-S154T User’s Manual 58
Appendix Pin Assignments B
Appendix B Pin Assignments B.1 Inverter Power Connector (CN4) Table B.1: Inverter power connector (CN4) Pin Signal 1 +24V 2 GND 3 ENABKL 2 4 Brightness Adj. 3 5 +5 V 1 5 B.2 Internal Speaker Connector (CN15) 1 2 3 4 Table B.
B.3 Floppy Drive Connector (CN9) Table B.
B.4 IDE Hard Disk Drive Connector (CN18) Table B.
B.5 CD-ROM Connector (CN19) Table B.
B.6 Touch Screen Sensor Connector (CN13) Table B.6: Touch Screen Sensor Connector (CN13) Pin Signal 1 YE- 2 YS- 3 YS+ 4 YE+ 5 XE- 6 XS- 7 XS+ 8 XE+ 1 8 B.7 IR Connector (CN26) 1 2 3 4 5 Table B.
B.8 CPU Fan Power Connector (FAN1) 1 2 3 Table B.8: CPU fan power connector (FAN1) Pin Signal 1 GND 2 +5 V 3 FAN_DET B.9 System Fan Power Connector (FAN2) 3 2 1 Table B.
B.10 Flat Panel Display Connector (CN3) Table B.10: Flat Panel Display Connector (CN3) 1 VDD(3.3V) 2 VDD(3.
B.11 Flat Panel Display Connector (CN5) Table B.11: Flat Panel Display Connector (CN5) 1 VDD(3.3V) 2 VDD(3.
B.12 COM1 1 6 7 8 2 3 4 5 9 Table B.
B.13 COM2 1 2 3 4 5 6 7 8 9 Table B.
B.14 COM3 1 6 7 8 2 3 4 5 9 Table B.
B.15 14 VGA connector (CN2) Table B.15: VGA connector (CN2) Pin Signal Pin Signal 1 2 RED 9 VGA G Vcc 10 VGA H 3 GREEN 11 VGA G 4 VGA G 12 VGA V 5 BLUE 13 VGA G 6 N/C 14 DDCSCL 7 N/C 15 VGA G 8 DDCSDA 16 N/C B.16 Parallel Port Connector (CN8)(Reserved) Table B.
B.17 TV OUT (S-VIDEO) connector (Reserved)(CN6) Table B.17: TV OUT (S-VIDEO) connector (Reserved)(CN6) Pin Signal 1 TV_Y 2 TV_C 3 GND 4 GND B.18 PS/2 Keyboard & mouse port (CN14) Table B.
