User Manual PPC-L61T AMD LX800 Processor based Fanless Panel PC with 6.
Copyright This document is copyrighted, © 2007. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy.
Packing List Before you begin installing your card, please make sure that the following materials have been shipped: PPC-L61T series Panel PC Accessories for PPC-L61T Warranty card DC plug-in housing (female) is connected on the AC/DC power adapter "Drivers, Utilities and User Manual" CD-ROM End User License Agreement (XPE and WinCE model) Mounting kits and packet of screws If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from humidity. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. 2. 3. Bitte lesen sie Sich diese Hinweise sorgfältig durch. Heben Sie diese Anleitung für den späteren Gebrauch auf. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
Contents Chapter 1 General Information ............................1 1.1 1.2 1.3 Introduction ............................................................................................... 2 General Specifications .............................................................................. 2 LCD Specifications.................................................................................... 4 Figure 1.1: LCD Specifications ..................................................... 4 Dimensions .........
4.2 4.3 PPC-L61T User Manual Jumper setting on Mother-Board ............................................................ 21 4.2.1 CMOS Clear for External RTC (JP1) .......................................... 21 Table 4.3: Clear CMOS / External RTC (JP1)........................... 21 4.2.2 AT/ATX power Setting Power feature setting (J1) ...................... 21 Table 4.4: AT/ATX Power setting (J1)....................................... 21 COM port interface.................................................
Chapter 1 1 General Information This chapter gives background information on the PPC-L61T Panel PC.
1.1 Introduction The PPC-L61T panel PC is an AMD low-power LX800 processor computer that is designed to serve a Human machine interface (HMI) and as a multimedia computer. It is a PC based system with 6.5"color TFT LCD display and aluminum front cover, the PPC-L61T is as compact and user friendly as a multi-function computer. For system integrators, the simple, complete, compact system lets you easily build a panel PC into your application.
Ethernet interface: Full compliance with IEEE 802.3u 100Base-T and 10 BaseT specifications. Includes software drivers and boot ROM that supports both RPL and PXE.
1.3 LCD Specifications Figure 1.1: LCD Specifications Display type Max. resolution Colors Dot size (mm) Luminance 6.5"TFT LCD Viewing Angle (Horizon/Vertical) Temperature LCD MTBF 140°/120° Note! 640 X 480 262K 0.207 X 0.207 400 cd/m2 -10 ~ 70°C 50,000 hours The color LCD display installed in the Panel PC is high-quality and reliable. However, it may contain a few defective pixels which do not always illuminate. With current technology, it is impossible to completely eliminate defective pixels.
Chapter 2 2 System Setup This chapter details system setup on the PPC-L61T Panel PC.
2.1 A Quick Tour of the Panel PC Before you start to set up the Panel PC, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below. When you place the Panel PC upright on the desktop, its front panel appears as shown in Figure 2.1. Figure 2.1 Front View of the PPC-L61T Panl PC When you look at the left side of the Panel PC, you will see the Complat Flash socket at left side as shown in Figure 2.2. Figure 2.
Chapter 2 When you turn the Panel PC around and look at its rear cover, you will find VESA standard holes (75x75mm) and power Button. As shown in Figure 2.3. System Setup Product Lable Power Button Figure 2.3 Rear View of the PPC-L61T The I/O section is at the bottom of the Panel PC, as shown in Figure 2.4. Figure 2.
2.2 Installation Procedures 2.2.1 Connecting the Power Cord The Panel PC can only be powered by a DC electrical outlet. Be sure to always handle the power cord by holding the plug ends only.Please follow the Figure 2-5 to connect the male plug of the power cord to the DC Inlet of the Panel PC. 2.2.2 Connecting the Keyboard or Mouse Before you start the computer, please connect the necessary mouse or keyboard to the USB ports. 2.2.
Recent releases of operating systems from major vendors include setup programs which load automatically and guide you operating system installation. The guidelines below will help you determine the steps necessary to install your operating system on the computer hard drive. Note! The BIOS of the computer supports system boot-up directly from the CDROM drive connected via USB interface. You may insert your system installation CD-ROM into the CD-ROM drive.
PPC-L61T User Manual 10
Chapter 3 3 Hardware and Peripheral Installation This chapter details the installation of the PPC-L61T hardware.
3.1 Overview of Hardware Installation and Upgrading The Panel PC consists of a PC-based computer that is housed in a ruggedized aluminum front panel. Any maintenance or hardware upgrades can be completed after removing rear panel. Warning! Do not remove the ruggedized covers until you have verified that no power is flowing within the computer. Power must be switched off and the power cord must be unplugged. Every time you service the Panel PC , you should be aware of this. 3.
5. 6. 7. 8. Detach and Remove the Rear cover. Remove the SATA HDD hole through (-) Screwdriver. Attach the SATA converter board to the Rear cover with two M2*5 screws. Connect the IDE HDD cable to the SATA converter. 13 PPC-L61T User Manual Hardware and Peripheral Installation Connect the SATA HDD cable to the SATA HDD. Plate the HDD Module into HDD Cover and tighten the screws. Chapter 3 3. 4.
9. Connect SATA cable to the SATA Converter board through the hole. 10. Fix the SATA cable with green adhesive tape. 11. Attach HDD cover on PPC-L61 back cover with Four M3*5 screws. 12. Attached VESA Bracket to the HDD. 13. Put the Rear cover on and tighten the screws.
1. 2. 3. Insert the WLAN module onto the MiniPCI slot on Motherboard. Tight the cable between the connector (main) on the WLAN module and the screw-in antenna hole on Middle Frame. Screw the antenna on the antenna hole on Middle Frame shown as below picture. RAM WLAN (Mini PCI) IDE Power Switch 3 15 PPC-L61T User Manual Chapter 3 3.3.
PPC-L61T User Manual 16
Chapter 4 4 Jumper Settings and Connectors This chapter tells how to set up the Panel PC hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installation procedures.
4.1 Setting Jumpers You can configure your Panel PC to match the needs of your application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
Chapter 4 4.1.2 Locating Jumpers on Motherboard SW1:PWR BTN J1:AT/ATX SEL CN13:COM1/2 Pin9 SEL CN12:Battery JP1:Clear CMOS Figure 4.1 Locating Jumpers on Motherboard 4.1.3 Connectors on Motherboard On-board connectors link the Panel PC to external devices such as hard disk drives. The table below lists the function of each connector. Table 4.
4.1.4 Locating Connectors on Motherboard Figure 4.2 Locating Connectors on the PPC-L61T Mother-board (front side) Figure 4.
4.2.1 CMOS Clear for External RTC (JP1) Warning! To avoid damaging the computer, always turn off the power supply before setting "Clear CMOS". Set the jumper back to "Normal operation" before turning on the power supply. Normal Operation (Default) 2 1 Clear CMOS 3 2 1 3 4.2.2 AT/ATX power Setting Power feature setting (J1) The default setting for PPC-L61T is ATX Mode, client can easy to adjust Power Mode to AT by jumper setting. Described as below: Table 4.
4.3 COM port interface The computer provides 2 serial ports: COM1, COM 2: RS-232/422/485 (selectable via BIOS setting) However, if you wish to disable the port or change these parameters later you can do this in the system BIOS setup. The table overleaf shows the default settings for the computer’s serial ports. COM1 and COM2 are one set. You can exchange the address range and interrupt IRQ of COM1 for the address range and interrupt IRQ of COM2.
Chapter 4 Jumper Settings and Connectors PPC-L61T User Manual 23
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
