User Manual PPC-L158T Intel Atom Processor- Based Panel PC with 15” Color TFT LCD Display
Copyright The documentation and the software included with this product are copyrighted 2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure.
Safety Instructions 1. 2. 3. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components.
PPC-L158T User Manual vi
Contents Chapter 1 General Information ............................1 1.1 1.2 Introduction ............................................................................................... 2 Specifications ............................................................................................ 2 1.2.1 General Specifications .................................................................. 2 1.2.2 Standard PC Functions................................................................. 2 1.2.
4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 Chapter Jumpers and Connectors........................................................................ 18 Disassembling the Panel PC .................................................................. 18 Figure 4.1 Unfastening the Rear Cover..................................... 18 Installing the 2.5" Hard Disk Drive .......................................................... 19 Figure 4.2 The PPC Side Cover ................................................ 19 Figure 4.
Table 5.21: CN29 (USB23).......................................................... 39 Table 5.22: CN30 A (COM1 RS232) ........................................... 40 Table 5.23: CN30B VGA ............................................................. 40 Table 5.24: CN31 A (COM2 RS232/422/485 Select by BIOS).... 40 Table 5.25: CN31 B (COM3 RS-232 serial port) ......................... 41 Table 5.26: CN32 (MIC IN).......................................................... 41 Table 5.27: CN33 (LINE OUT) .........
PPC-L158T User Manual x
Chapter 1 1 General Information This chapter gives background information on the PPC-L158T.
1.1 Introduction Advantech PPC-L158T is an Intel Atom processor based Panel PC with a bright 15" LCD display. The powerful Atom CPU and Intel ICH8M chipsets bring the most dynamic applications to life without sacrifices to any industrial reliability. The Internal CFast card interface can serve as an alternate HDD solution for OS booting and the Mini PCIe interface can be used by many expansion cards such as a wireless LAN card to extend device mobility.
Chapter 1 1.2.6 Touchscreen Specifications (Optional) Table 1.1: Touchscreen Specifications Type Analog Resistive 2048*2048 Light Transmission 80% Controller COM/USB Power Consumption +5.5 V @ 70 mA Software Driver Windows Durability (touches in a lifetime) 35 million 1.2.7 Optional Modules CPU: Supports Intel Atom processor, dual-core D525 1.8 G Memory: Supports up to 4 GB DDR3 SDRAM [204-pin SODIMM socket x 2] HDD: Supports 2.
1.3 Dimensions Figure 1.
Chapter 2 2 System Setup This chapter gives system setup information for the PPC-L158T.
2.1 A Quick Tour of the Panel PC Before starting to set up the panel PC, take a moment to become familiar with the locations and purposes of controls, drives, connectors and ports, which are illustrated in the figures below. When placed upright on the desktop, the front panel of the panel PC appears as shown in Figure 2.1. Figure 2.1 Front Panel of PPC-L158T When viewed from the left side of the panel PC, the optical device drive, USB ports are visible, as shown in Figure 2.2.
A: Line out/Mic in C: IEEE 1394 x 2 (optional) E: VGA Port G: PS2 Mouse x 1 / Keyboard x1 I: AC Inlet K: 10/100/1000 Mbps Ethernet x 1 B: 10/100/1000 Mbps Ethernet x 1 D: USB 2.0 x 4 F: RS-232 x 2, RS-232/422/485 x 1 H: Power Switch J: RS-232 x 1 (or GPIO x 1 by cable swapping) L: PCI Slot x 1 (or PCIe Slot x 1) Figure 2.
VESA standard, both 100 x 100 mm and 75 x 75 mm mounting size. Figure 2.5 Rear View of the Panel PC Caution! Use recommended mounting apparatus to avoid risk of injury.
Before commencing set up of the panel PC system, the following items should be available: Keyboard Mouse (for system software installation) Chapter 2 2.2 Preparing for First-time Use 2.3 Installation Procedures The panel PC can be powered through an AC electrical outlet (100 ~ 250 volts, 50 ~ 60 Hz) or DC outlet (15 ~ 24 V). Be sure to handle the power cords by holding the plug ends only. Follow these procedures in order: 1. Connect the female end of the power cord to the AC/DC inlet of the panel PC.
2.6 Installing the Drivers After installing your system software, you will be able to set up the Chipset, Ethernet, VGA, audio and touchscreen functions. All the drivers are stored in a CD-ROM disc labeled "Drivers and Utilities”. The CD-ROM can be found in your accessory box. Figure 2.6 Drivers and Utilities on the CD-ROM Note! The drivers and utilities used for the PPC-L158T panel PCs are subject to change without notice.
Chapter 3 3 Using the Panel PC This chapter explains onboard devices and peripheral I/O ports available on the PPC-L158T.
3.1 Introduction This chapter describes basic features and procedures for using the panel PC. Topics covered include: the CD-ROM drive, I/O ports and the touchscreen. This product is a high performance panel PC, please keep upright (see Fig. 3.1). 3.2 CD-ROM Drive (Optional) It is possible to use the USB external optical device. To insert a CD-ROM disc, press the eject button on the CD-ROM drive. To eject a CD-ROM disc, first ensure that the drive activity light is not active.
1. 2. 3. 4. 5. To install a full-size desktop PS/2 keyboard and mouse with the panel PC, follow these instructions: Be sure the panel PC is turned off. Attach the keyboard to the purple colored 5-pin PS/2 port. Attach the PS/2 mouse to the green colored port. Turn on the panel PC. The panel PC supports either one PCI or one PCIe bus expansion card. To integrate a new expansion bus card into the system, follow these instructions: 1. Turn off the panel PC. 2.
3.5 Serial COM Ports There are four serial COM ports on the bottom. It is simple to attach a serial device to the panel PC, such as an external modem or mouse. Follow these instructions: 1. Be sure the panel PC and any other peripheral devices that are connected to the panel PC are turned off. 2. Attach the interface cable of the serial device to the panel PC's serial port. (See Figure 3.3.) If necessary, attach the other end of the interface cable to the serial device. Fasten any retaining screws. 3.
An external VGA-compatible device may be connected to the system through the 15pin external port located on the bottom of the system unit. The panel PC simultaneously supports an external CRT monitor in addition to the built-in LCD display. 1. Be sure the panel PC is turned off. 2. Connect the external monitor to the system. (See Figure 3.3.) 3. Turn on the panel PC and the external monitor.
PPC-L158T User Manual 16
Chapter 4 4 Hardware Installation This chapter gives instructions for installing hardware devices on the PPC-L158T.
4.1 Jumpers and Connectors The panel PC consists of a PC-based computer that is housed in a metal shielding case with a plastic cover on the rear and bottom. All the computer devices, like the CPU, HDD, SDRAM, and power supply are all readily accessible after removing the rear panel or the HDD cover. Any maintenance or hardware upgrades can be easily completed after removing the rear panel and/or HDD cover.
One enhanced Serial ATA (SATA) hard disk drive may be attached to the panel PC. The following instructions are for installing the HDD: 1. Remove the two screws on side cover first. (See Figure 4.2) Hardware Installation Figure 4.2 The PPC Side Cover 2. Remove the four screws on the metal plate on both sides of the HDD. (See Figure 4.3) Figure 4.3 The PPC HDD 19 Chapter 4 4.3 Installing the 2.
3. Connect the SATA cable from the mainboard. Figure 4.
The panel PC system provides two 204-pin SODIMM sockets and it is possible to install 4 GB of DDR3 SDRAM memory. Figure 4.6 Stick the Thermal Pad on the Memory Heatsink 21 PPC-L158T User Manual Hardware Installation Figure 4.5 Placing the Memory Module in the SODIMM Socket Chapter 4 4.
Figure 4.
1. Chapter 4 4.5 Installing the Optical Device Drive Remove all the screws on the rear cover. Hardware Installation Figure 4.8 Rear Cover Photo 2. Plug in the SATA ODD cable. Figure 4.
3. Place ODD on device bracket, then fasten screws on IO shielding. Figure 4.10 Fasten Screw on IO Shielding 4. Fasten screws on the ODD bracket. Figure 4.
The GPIO cable uses same cable as COM4 Figure 4.12, so just change the cable PIN header from CN18 to CN11, see Figure 4.13. Figure 4.13 Change Cable PIN Header to CN11 25 PPC-L158T User Manual Hardware Installation Figure 4.12 GPIO Location on I/O Bracket Chapter 4 4.
4.7 Installing the LPT Cable Fetch LPT cable from accessory box. 1. Remove system rear cover and device brackets, remove the original bracket on the I/O bracket, and insert the LPT cable PIN header on the motherboard CN37 location. Figure 4.14 Insert LPT Cable PIN Header on the Motherboard 2. Assemble the device bracket, then fasten the LPT cable bracket on the I/O bracket.
4. The completed LPT cable assemblage below. Figure 4.17 Completed Photo of LPT Cable Assemblage 27 PPC-L158T User Manual Hardware Installation Figure 4.16 Fasten the Screw on the Bracket Chapter 4 3. Figure 4.15 Fix the LPT Cable on the I/O Bracket Remember to secure the LPT bracket and I/O bracket with a screw.
4.8 Installing Dual-USB Cable Fetch dual-USB cable from accessory box. 1. Remove the rear cover and device brackets, remove the original bracket on I/O bracket, and insert the dual-USB cable PIN header on motherboard CN9 or CN10 location. Figure 4.18 Insert Dual-USB Cable on CN9 or CN10 2. Assemble the device bracket, then fasten the dual-USB cable bracket on the I/O bracket.
Chapter 4 Figure 4.20 Fasten Screw on Bracket 29 PPC-L158T User Manual Hardware Installation 3. Figure 4.19 Dual-USB Cable Assembly on I/O Bracket Remember to secure dual-USB bracket and I/O bracket with a screw.
4. Completed assembly as below. Figure 4.
Chapter 5 5 Jumpers and Connectors This chapter gives information on setting jumpers and using the connectors on the PPC-L158T motherboard.
5.1 Jumpers and Connectors This chapter supplies more detailed information about the internal jumper settings and an outline of the I/O ports available on the PPC-L158T. 5.1.1 Setting Jumpers The Panel PC can be configured to match the needs of each application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover), which slides over the pins to close the circuit and connect them.
The motherboard of the panel PC has a number of jumpers that help configure the system. It also has LED indicator lights that display the system operation status. The table below lists the function of each jumper and LED. The motherboard of the PPC-L158T has a number of jumpers that allow you to configure your system to suit your applications. CMOS CLEAR & AT/ATX Select CN19 Ring and Power for COM1/2 pin 9 Jumpers and Connectors JP1 Table 5.
5.1.3 Jumper and Connector Locations CN1 CN12 CN13 CN2 CN6 CN3 CN4 CN5 CN7 CN14 CN9/10 CN37 CN19 CN16 CN18 CN35 CN21 CN20 CN22 CN23 CN34 CN25 CN31 CN30 CN11 CN29 CN24 CN28 CN32 CN33 CN26/27 Figure 5.
Onboard connectors link the panel PC to external devices such as hard disk drives. The table below lists the function of each of connectors.
Table 5.4: CN2/3 (SATA Power) Pin Pin Name 1 +V3.3 2 GND 3 +V5 4 GND 5 +V12 Table 5.5: CN4/5 (SATA0/1) Pin Pin Name 1 GND 2 SATA1_TX+ 3 SATA1_TX- 4 GND 5 SATA1_RX- 6 SATA1_RX+ 7 GND 8 GND 9 GND Table 5.
Chapter 5 Table 5.7: CN7 (MiniPCIE) Pin Standard connect Table 5.8: CN9/10 (USB4/5/6/7) Pin Name 1 +V5_USB 2 +V5_USB 3 USB4//6_P- 4 USB5/7_P- 5 USB4//6_P+ 6 USB4//6_P+ 7~10 GND Jumpers and Connectors Pin Table 5.9: CN11 (GPIO) Pin Pin Name 1 GND 2 GPIO4 3 GPIO0 4 GPIO5 5 GPIO1 6 GPIO6 7 GPIO2 8 GPIO7 9 GPIO3 10 +V5 Table 5.10: CN12/13 (Memory 0/1) Pin Standard connect Table 5.
Table 5.12: CN18 (COM4) Pin Pin Name 1 COM4_DCD# 2 COM4_RX 3 COM4_TX 4 COM4_DTR# 5 GND 6 COM4_DSR# 7 COM4_RTS# 8 COM4_CTS# 9 COM4_RI# 10 +5v Table 5.13: CN20 (LED Connect) Pin Pin Name 1 GND 2 LAN2_LED0 3 LAN1_LED0 4 SATA_LED# 5 +V5 Table 5.14: CN21 (Button) Pin Pin Name 1 PWRBTN# 2 GND Table 5.15: CN22 (DC IN (For 12V)) Pin Pin Name 1 DC_IN (+12v) 2 DC_IN (+12v) 3 GND 4 GND Table 5.
Chapter 5 Table 5.17: CN24 (LAN1&USB01) Pin Standard connect Table 5.18: CN25 (PS2) Pin Standard connect Jumpers and Connectors Table 5.19: CN26/27(1394) Pin Pin Name 1 +V12 2 GND 3 XTPBM 4 XTPBP 5 XTPAM 6 XTPAP Table 5.20: CN28 (LAN2) Pin Pin Name 1 MDI0+ 2 MDI0- 3 MDI1+ 4 MDI1- 5 VDC1 6 VDC2 7 MDI2+ 8 MDI2- 9 MDI3+ 10 MDI3- 11 +3.3V 12 ACT# 13 LINK1000# 14 LINK100# Table 5.
1 2 3 4 5 6 7 8 9 Table 5.22: CN30 A (COM1 RS232) Pin Pin Name 1 COM1_DCD 2 COM1_RXD 3 COM1_TXD 4 COM1_DTR 5 GND 6 COM1_DSR 7 COM1_RTS 8 COM1_CTS 9 RIA Table 5.23: CN30B VGA Pin Standard Connect 1 2 3 4 5 6 7 8 9 Table 5.
Chapter 5 1 2 3 4 5 6 7 8 9 Table 5.25: CN31 B (COM3 RS-232 serial port) Pin Name 1 DCD# 2 RX 3 TX 4 DTR# 5 GND 6 DSR# 7 RTS# 8 CTS# 9 R# Jumpers and Connectors Pin Table 5.26: CN32 (MIC IN) Pin Pin Name 1 GND_AUD 2 MIC1_z_L 3 GND_AUD 4 MIC_JD 5 MIC1_z_R Table 5.27: CN33 (LINE OUT) Pin Pin Name 1 GND_AUD 2 LOUT_z_L 3 GND_AUD 4 FRONT_JD 5 LOUT_z_R Table 5.
PPC-L158T User Manual 42
Chapter 6 6 Driver Installation This chapter gives information on installing drivers for the PPCL158T.
6.1 Introduction A Driver CD is supplied inside the accessory box. Customers may need to use an external USB CD-ROM related device to load the CD and install the drivers for the PPC-L158T. 6.1.1 Driver Installation Before installing the Ethernet driver, note the procedures below. It is necessary to know which operating system is installed on the PPC-L158T. Then refer to the corresponding installation flow chart. Follow the steps described in the flow chart to complete the installation quickly.
Appendix A A PCI Card and PCIe Size Limits This chapter details the size limits for PCI and PCIe cards that may be installed on the Panel PC motherboard.
A.1 PCIe Interface Card A.
Appendix A PCI Card and PCIe Size Limits A.
PPC-L158T User Manual 48
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
