POC127 Point of Care Terminal with Intel® Pineview-M N450 CPU and 12.
The Instructions for the User The document combines text and illustrations, providing a comprehensive overview of the system. The information is presented as sequential steps of action, allowing the user to learn directly how to use the device. The text provides explanations and instructs the user step by- step in the practical use of the product, with short, clear instructions in easy-to-follow sequence.
5. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning and keep this equip-ment away from humidity. Caution! To avoid short-circuiting and otherwise damaging the device, do not allow fluids to come in contact with the device. If fluids are accidentally spilled on the equipment, remove the affected unit from service as soon as possible and contact the service personnel to verify that patient safety is not compromised. 6.
11. Environmental protection: follow national requirements to dispose of unit. 12. Maintenance: to properly maintain and clean the surfaces, use only the approved products or clean with a dry applicator. Caution! When servicing the device, always use replacement parts that are qualified to Advantech standards. Advantech Digital Healthcare cannot warrant or endorse the safe performance of third-party replacement parts for use with our medical device. 13.
Furthermore all configurations shall comply with the system standard IEC 60601-1- 1. Anyone who connects additional equipment to the signal input part or signal output part is configuring a medical system, and is therefore, responsi - ble that the system complies with the requirements of the system standard IEC 60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified equipment in the patient environment and IEC 60XXX certified equipment out-side of the patient environment.
Disposing of Old Products Within the European Union EU-wide legislation, as implemented in each member state, requires that waste electrical and electronic products carrying the mark shown at left must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords.
List of Accessories Before installing your Point-of-Care Terminal, ensure that the following materials have been received: POC127 series Point-of-Care Terminal Accessories for POC127 CD-ROM disc-"Drivers, User's manual and Utilities" Mounting kits and packet of screws. VESA mounting note x1 China RoHS notex1 Warning! No user serviceable parts inside; refer servicing to qualified personnel.
Visit the Advantech websites at www.advantech.com or www.advantech.com.tw if you need more information.
Chapter 1 General Information 1.1 Introduction The POC127 is a Intel® Atom™ Processor Processor N450 1.66G Hz mobile processorbased computer that is designed to serve as a Point of Care terminal (POC.) It is a PC-based system with 12.1” color TFT LCD display, Single DVI-I Port, Dual on-board 10/100/1000 PCIE Ethernet controller, Quad COM ports, Quad USB 2.0 ports and a 24-bit stereo audio controller.The POC127 is an user-friendly computer.
1.2 Specifications Chipset Intel Pineview-M; Intel ICH8M CPU Intel® Atom™ Processor Processor N450 1.66G Hz Front Side Bus 667 MHz Memory Up to 2GB DDR2 667 MHz SDRAM Graphics Controller INTEL Pineview-M with Extreme Graphic technology System input rating Input Voltage +18 VDC,3.5 A. DC Model AC/DC adapter (Sinpro Model no.HPU101-107) Input Voltage 100-240V AC, 47-63Hz, 1.2-0.5A Output Voltage +18 VDC,5.55 A.
Light transmission 75% Controller RS-232 interface (use COM 6) Durability 30 million touches CE,FCC Class B approved/ RF Certification Controller Temperature Environment Humidity Pressure Physical Characteristics Platform & utility UL60601-1,EN60601-1 approved 0 ~ 40°C (32 ~ 104°F) (Operating) -20 ~60°C (Storage) -20 ~60°C (Transportation) 10 ~ 90% @ 40°C (non-condensing) 5 ~90% (non condensing) (Storage) 5 ~90% (Transportation) 700-1013 hPa (Operation) 375 mmHg to 760 mmHg (Storage) 375mmHg
Figure 1-1: Dimension
VESA Mounting: 75x75mm Figure 1-2: VESA Mounting Please use M4x12L (Maxium)screw x4 Cleaning and Disinfecting During normal use of the POC (Point-of-Care Terminal) the device may become dirty and should be regularly cleaned. Steps: 1. Prepare cleaning water 2. Wipe the POC with a clean cloth that has been moistened in the pure water. 3. Wipe thoroughly with a clean cloth. Caution! ○ Do not immerse or rinse the POC or its peripherals.
or abrasives. Never immerse electrical connectors in water or other liquids.
Chapter 2 System Setup 2.1 A Quick Tour of the POC127 Before you start to set up the POC127, take a moment to become familiar with the locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below. When you place the POC127 upright on the desktop, its front panel appears as shown in Figure 2-1. 2.1.
2.1.2 Rear View When you turn the Point of Care Terminal around and look at its rear cover, the sunken I/O section is at the bottom of the panel PC, as shown in Figure 2-2 and zoom in Figure 2-3. (The I/O section includes various I/O ports, including serial ports, VGA port, the Ethernet port, USB ports and so on.
2.1.3 Bottom view (12) (13) (9) (10) (11) Figure 2-4: Bottom view (9) DC-in Jack (10) Power switch (11) Equipotential terminal (12) Add on card bracket (13) Speaker x2 NOTE: Equipotential terminal need link to hospital ground/earth system before system boot to protect operator and system.
2.2 Installation Procedures 2.2.1 Connecting the Power Cord The POC127 could only be powered by a DC power adapter (SINPRO Model no.HPU100107). Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: 1. Connect the female end of the power adapter to the DC jack of the panel PC. (See Figure 2-7.) 2. Connect the female end of the power cord to the DC power adapter 3. Connect the 3-pin male plug of the power cord to an electrical outlet.
2.2.2 Connecting the Ground Pin Step 1. System ready and find the Equipotential Terminal on rear side of POC. An Equipotential Terminal is provide to optionally connect to a hospital ground/earth system Equipotential Terminal Figure 2-8: POC127 Equipotential Terminal Pin Step 2. Prepare the Grounding cable and the other terminal link to hospital ground/earth system. Figure 2-9: Grounding cable with connector Step 3.
2.2.2 Switch on the power Switch on the reset switch on the front cover. (See Figure 2-4.
2.3 Running the BIOS Setup Program Your POC127 is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of hard drive. The setup program is stored in read-only memory.
2.4 Installing System Software Recent releases of operating systems from major vendors include setup programs which load automatically and guide you through hard disk preparation and operating system installation. The guidelines below will help you determine the steps necessary to install your operating system on the panel PC hard drive. Note! Some distributors and system integrators may have already pre-installed system software prior to shipment of your panel PC.
2.5 Installing the Drivers After installing your system software, you will be able to set up the Chipset, Graphics, Ethernet, Audio, and Touchscreen functions from your own external CD-ROM drive. All the drivers except the CD-ROM drive driver are stored in a CD-ROM disc entitled "Drivers and Utilities." 7. The standard automatic installation procedures for installing the Chipset, Graphics, Audio, Ethernet, TXE and Touch drivers are described in Chapter 3. 8.
prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the model POC127 as recommended below, according to the maximum output power of the communications equipment.
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity POC127 is intended for use in the electromagnetic environment specified below. The customer or the user of the model POC127 should assure that it is used in such an environment. Compliance Level Electromagnetic Environmental Guidance ±6 kV contact ±8 kV air ±6 kV contact ±8 kV air Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity The model POC127 is intended for use in the electromagnetic environment specified below. The customer or the user of the model POC127 should assure that it is used in such an environment.
Operation and Safety Information 3.1 General Safety Guide For your own safety and that of your equipment, always take the following precautions.
an outlet because the outlet is not grounded, contact a licensed electrician to replace the outlet with a properly grounded outlet. Do not defeat the purpose of the grounding plug. Warning! Never push objects of any kind into this product through the openings in the case. Doing so may be dangerous and result in fire or a dangerous electric shock. Never place anything on system case before turning off the computer. Never turn on your computer unless all of its internal and external parts are in place.
A.1 Install VESA Mounting The POC127 also provides standard VESA mounting to help system integrators conveniently integrate the panel PC into their system. Never use mounting brackets except as provided by Advantech to prevent unreliable mounting of the POC127. VESA mount installation should be carried out by a professional technician; please contact a service technician or your retailer if you need this service. Installation instructions follow: 1.
Page 30 of 30 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.