User Manual PDC-190S
Copyright The documentation and the software included with this product are copyrighted 2009 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item is missing, please contact your dealer immediately. ! PDC-190S display monitor ! Accessories for PDC-190S – AC/DC power adapter (MPU100-105, P/N: 1757000275) – DVI-D cable (2 m, P/N: 1700000243) – USB cable (1.8 m, P/N: 1700041800) for host to hub – Audio cable (1.
Additional Information and Assistance 1. 2. Visit the Advantech websites at www.advantech.com or www.advantech.com.tw where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Read these safety instructions carefully. Keep this User's Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from humidity.
21. Contact information: No.1, Alley 20, Lane 26, Reuiguang Road Neihu District, Taipei, Taiwan 114, R.O.C. TEL: (02) 2792-7818 22. This equipment shall not be used for life support system. 23. Accessory equipment connected to the analog and digital interfaces must be in compliance with the respective nationally harmonized IEC standards (i.e. IEC 60950 for data processing equipment, IEC 60065 for video equipment, IEC 61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.
Contents Chapter 1 General Information ............................1 1.1 1.2 1.3 Introduction ............................................................................................... 2 Specifications ............................................................................................ 2 Connectors................................................................................................ 4 Figure 1.1 PDC-190S connection port......................................... 4 1.3.
A.10 A.11 A.12 A.13 A.14 A.15 A.16 A.17 A.18 A.19 A.20 A.21 A.22 A.23 A.24 Phase* .................................................................................................... 21 Clock*...................................................................................................... 21 Display Control........................................................................................ 21 A.12.1 Display Image ............................................................................. 22 A.
Chapter 1 1 General Information
1.1 Introduction The PDC-190S LCD monitor is designed specifically for medical environments. The monitors comply with key safety requirements and are ideal for use in endoscopy, surgery, patient monitoring, radiology and more. Slim and light, they can be used in many installations - fixed to a wall or ceiling, mounted on a standard arm or installed on the optional stand. The front side of the PDC-190S is IP65 certified dust and water resistant to ensure reliability in medical environments.
0 ~ 40 (Operating) Humidity 10 ~ 95%@40 (non-condensing) Vibration / 5 ~ 500 Hz, 1G acceleration / Shock Resistance 20 G half sine, 11 msec duration Water/dust ResisIPX1 for whole system tance Dimensions Physical (W x H x D) Characteristics Weight 471.5 x 416.2 x 110.8 mm (18.56” x 16.38” x 4.36”) Chapter 1 Environment Temperature 6.5 kg (14.
1.3 Connectors Figure 1.1 PDC-190S connection port The following connectors are situated on the rear of the PDC-190S (From left to right): 1.3.1 DC 12V Power In The connector is connected to the DC 12V Switching Power Supply. 1.3.2 Analog and Digital Port (DVI-I) The DVI-I connector integrates the analog RGB and digital DVI in one port, that can be selected via "source" OSD button to switch which signal you want to input into the monitor.
18 T.M.D.S. Data0+ 19 T.M.D.S. Data0/5 Shield 20 T.M.D.S. Data5- 21 T.M.D.S. Data5+ 22 T.M.D.S Clock Shield 23 T.M.D.S Clock + 24 T.M.D.S Clock - C1 Analog Red C2 Analog Green C3 Analog Blue C4 Analog Horizontal Sync C5 Analog Ground (Return of analog R,G,B) 1.3.3 Serial Remote RS-232C Port (DB-9, female) Connects the RS-232C control connector on external equipment to the monitor. The monitor can be operated according to control commands sent from external equipment connected to it.
1.3.10 Equipotential Terminal Connects the equipotential plug in the European Market. 1.4 Dimensions Figure 1.
Chapter 2 System Setup 2
2.1 Location and Function of Parts and Controls Before you start to set up the PDC-190S, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below. When you place the PDC-190S upright on the desktop, its front panel appears as shown in Figure 2.1. Figure 2.1 Front Panel of PDC-190S Table 2.
Multi-display On/Off Multiple display Enable/Display Press to enable/disable multiple display. Figure 2.2 I/O Section of PDC-190S Table 2.2: I/O Connectors of PDC-190S No I/O Function DC 12V IN connector (DIN 4 Connect the DC connect of the supplied AC pins) adapter. Serial Remote RS-232C con- Connect to the RS-232C control connector on nector (D-Sub 9)_ external equipment connected to the monitor.
PC Line IN/Audio Line IN connector (2.5 mm phone jack) Input connector for audio signals. USB Hub Port (type A) USB downstream port (to peripheral USB devices). Connects the equipotential plug (As below picture). Equipotential terminal DVI-I input connector Inputs DVI Rev.1.0 applicable digital RGB signal. Or inputs an analog RGB video signal (0.7 Vp-p, positive polarity) and sync signal. YPbPr/RGBS input connector Input connector for component video signals / RGB signals.
2.3.1 Connect DVI Cable Connect the DVI-D cable to the DVI-I connector of the monitor. If the cable does not seem to fit, it may be facing the wrong direction. Please turn the cable over and try it. Chapter 2 2.3 Installation Procedures Caution! When the DVI-D signal is active, analog VGA input is not available. Connect the DVI-I to VGA cable to the DVI-I connector of the monitor. If the cable does not seem to fit it may be facing the wrong direction.
2.3.6 Connect SDI Signal Cable Connect the BNC (75 ohms) cable to the SDI IN connector of the monitor. If you have a loop-through requirement, please prepare another BNC (75 ohms) cable for connection to the SDI OUT connector on the bottom of the SDI IN connector. The IN connector is terminated internally at 75 ohms when nothing has been connected to the output connector.
Appendix A OSD Selections A
A.1 Introduction When you place the PDC-190S upright on the desktop (Landscape display), you will see eight keys located on the bottom of front panel. Their function is described in the table below: Icon SOURCE Control Function Power Button Power control Press the On/Off button to power the LCD monitor. Source Input select buttons Press the button to monitor the signal input to each connector. MENU Up Press to select items Scroll up the list of adjustment items.
Level 1 Level 2 Level 3 Level 4 Value Description While detect of VGA/DVI signal Image Brightness 0-100 Controls analog amplitude on input ADC Contrast 0-100 Controls analog black level on input ADC Hue(*) (*active in Video Input) 0-100 Saturation(*) (*active in Video Input) 0-100 Sharpness 0-100 Adjusts image position for centered image Color Auto Color(*) (*active in VGA mode) Auto adjust color temperature Color Temp. 0 User 2.
Aspect Ratio* (*active in Aspect mode) 0- Auto 1- 4:3 2- 16:9 Display Position (*active in VGA mode) PIP Function 0- ON 1- OFF PIP Default is OFF PIP Input 0- Large 1- Medium 2- Small 3- Side PIP Size PIP Position PIP Color Brightness adjust 0-100 Controls analog black level on input ADC Contrast adjust 0-100 Controls analog amplitude on input ADC Hue(*) (*active in PIP Video Input) 0-100 Saturation(*) (*active in PIP Video Input) 0-100 Blend 0-15 Volume 0-20 Mute ON/OFF Sound While
OSD Duration Adjust the time period for OSD menu disappear (Unit: second) OSD Position Adjusts position of OSD Factory Reset Load Default A.2 Main Menu Descriptions The LCD monitor is capable of accepting both digital and analog signal inputs and therefore has two different sets of OSD control functions. Since digital signaling always gives optimal display quality without much adjustment, it requires fewer OSD functions than the analog input mode.
A.4 Contrast Descriptions* Selecting this control allows you to make adjustments to the contrast level of the display screen on a scale of 0 to 100. Use the key on the front bezel to adjust the contrast any time the OSD is on. Note! This setting is only available on D-sub & video input, S-Video, composite, component/RGBS, SDI. A.5 Hue Descriptions** Selecting this control allows you to make adjustments to the color tones of the display screen on a scale of 0 to 100.
Selecting this control allows you to make adjustments to the Gamma and color temperature level of the display screen. Use the key on the front bezel to adjust the contrast any time the OSD is on. Note! This setting is only available on D-sub & video input, S-Video, composite, component/RGBS, SDI. Figure A.2 Item Color in OSD display A.8.1 Auto Color* Selecting this control allows you to adjust the color intensity, and color tones of input signal automatically. A.8.
A.8.3 User* If you set the Color Temp to a value of User 2.2, the item displayed is changed from dark to light white, which means that you can adjust the color temperature. This control allows you to adjust the color gain for each channel of RGB. A.9 Auto Configuration* Selecting this control allows you to adjust to monitor the picture more clearly automatically. Note! This setting is only available on D-sub (VGA).
Selecting this control allows you to adjust the frequency / sampling rate of horizontal pixels, to equal the video source’s value, thus minimizing the screen artifacts of shimmering vertical lines. Note! This setting is only available on D-sub (VGA). A.11 Clock* Selecting this control allows you to adjust the ADC (analog/ digital conversion) sampling clock phase so that the screen image appears crisp and focused.
A.12.1Display Image Mode Function Auto Select this control to fill the image on the full screen automatically, and discard the aspect ratio of the original input video signal. Aspect Select this control to change the aspect ratio of the picture from 4:3 to 16:9 or 16:9 to 4:3. 1:1 Select this control to display the picture in the original resolution of the input signal.
Note! This function works only when displaying the picture in the Aspect mode, and does not work when displaying the picture in the Auto/1:1 mode. Mode Function Auto Select this control to obtain an optimum image accord to the aspect ratio of the input video. 4:3 Use this function when a 16:9 aspect ratio picture is squeezed into a 4:3 format signal. 16:9 Use this function when a 4:3 aspect ratio picture is zoomed out to a 16:9 format signal. A.12.
A.13 PIP (Enable/Disable) Select this control to adjust multi display settings. Selects ON to display the multi display and OFF not to display. Note! This function works only when main display resolution is smaller than 1280 x 1024, 70 Hz. When the frame frequency of the main display is different from that of the sub display, the picture may be disturbed. When no signal is input to the main display, the picture may not be displayed correctly. A.
Select this control and then use four keys ( ↑↓←→ ) to adjust the horizontal position and vertical position of the sub display while PIP size is not on the side by side mode. A.17 PIP Color Selecting this control allows you to control the brightness/contrast/hue/saturation of the sub display. A.18 Blend Select this control, then use the key to adjust the blending level of sub display. 25 PDC-190S User Manual Appendix A OSD Selections A.
A.19 Volume Selecting this control allows you to adjust the volume of the two inside speakers if you have audio signal input from the line in port. A.20 Mute Selecting this control allows you to mute the volume of the two inside speakers. A.21 Input Signal (Main Input Select) Select this control to set the input signal of the main display.
A.22 Language Select this control, to select the OSD Language you want. A.23 OSD Display Descriptions Selecting this submenu allows you to adjust various settings of the OSD to make the display adjustment process an easier task. ! OSD Duration: Selecting this control allows you adjust the time period for OSD menu disappear (Unit: second). ! OSD Position: Selecting this control allows you to move the OSD menu vertically/Horizontally on the screen. A.
PDC-190S User Manual 28
Appendix B B Timing of Input Signal
B.1 Compatibility of VESA Timing The LCD monitor is capable of accepting both the traditional analog RGB video signaling and the new digital DVI (Digital Visual Interface) signaling. Due to its digital design and the implementation of this new digital standard interface, setting frequency mode is not necessary for a user and it will be handled automatically between the monitor and the digital graphic card adapter. For analog input, the LCD monitor operates at horizontal frequencies between 35.
The LCD monitor can display NTSC and PAL signals by connecting this unit. The NTSC or PAL color system or DTV format such as 720p, 1080i, etc. can be selected automatically. For acceptable formats, please refer to Table B.2 “Acceptable Timing of Composite/S-Video Input Signal”. Acceptable Timing of Composite/S-Video Input Signal Format (Resolution/V) CVBS S-Video Format Relevant Standard 710x482 /60 V V 710x482 /60 V 710x482 /60 V 702x574 /50 V 713x482 /59.
PDC-190S User Manual 32
Appendix C C Cleaning/Disinfecting
C.1 On Cleaning the Monitor During normal use of the PDC the device may become dirty and should be regularly cleaned. The protection plate surface is especially treated to reduced reflection of light. When solvents such as benzene or thinner, acid, alkaline or chemical cleaning cloth is used for the protection plate surface, the performance of the monitor may be impaired or the finish of the surface may be damaged.
Appendix D D Serial Remote Control
D.1 Using Serial Communications The monitor can be operated according to control commands sent from external equipment connected to it, e.g., a personal computer. For details on the pin assignment and command protocol please refer to the section below: Steps: 1. Prepare an RS-232C cable. 2. Connect the male end to the RS-232C terminal port on the PDC-190S. 3. Connect the female end to the RS-232C terminal port on the personal computer.
To start communication, send the connection command from the personal computer etc. For details, see table D.2 below. The command packet consists of four bytes. They are: two bytes of fixed header, one byte of command data, and one byte of Check sum calculated in ((summation of 04h, 12h, command data) + 01h) 04h 12h Command Data Check Sum Figure D.1 Communication packet format Table D.
PDC-190S User Manual 38
Appendix E Error Messages E
E.1 General Sometimes you may see error messages from the LCD display. This means that the LCD display cannot correctly receive the signal from the computer graphics card or video equipment or is there is an under processing signal. There are three kinds of messages which may appear. Check the connected cables first or contact your local dealer for more information. E.
Appendix E Error Messages PDC-190S User Manual 41
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
