PCM-9550F PCM-9550FM PCM-9550L EBX Pentium® SBC with CPU, LCD, Ethernet, Audio, DIO, and PC/104-Plus User's Manual
Copyright Notice This document is copyrighted, 2000. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Packing list Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-9550F/FM/L all-in-one single board computer • 1 CD disk for utility and drivers • 1 startup manual • 1 Power cable (p/n: 1703080101) If any of these items are missing or damaged, contact your distributor or sales representative immediately. Please refer to Appendix E, Section E.1 for the optional interface wiring kits.
Contents Chapter 1 General Information ...................... 1 1.1 1.2 1.3 1.4 Introduction ........................................................................................... 2 Highly integrated multimedia SBC ......................................................... 2 Features ................................................................................................. 3 Specifications ........................................................................................ 4 1.3.
2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24 2.25 2.13.1 Speaker ...................................................................................... 22 2.13.2 LED interface ............................................................................ 22 2.13.3 Watchdog output ....................................................................... 22 2.13.4 Reset switch .............................................................................. 22 Power connectors (CN24, CN8, CN26) ....
Chapter 3 Software Configuration .............. 39 3.1 3.2 3.3 Introduction ......................................................................................... 40 Connections for five standard LCDs ................................................ 40 3.2.1 Connections to Sharp LM64183P, LM64P89 (640 x 480 DSTN MONO LCD) ........................................................ 40 3.2.2 Connections to PLANAR EL (640 x 480 AD4 EL) .................. 41 3.2.
Chapter 6 Video ............................................. 77 6.1 6.2 6.3 Introduction ......................................................................................... 78 Installation of video driver ................................................................ 78 6.2.1 Installation for Windows 95/98 ................................................... 79 Installation of Chips-TV utility ........................................................ 83 Chapter 7 Audio .............................
C.11 Front panel connector (CN13) .......................................................... 121 C.12 USB connector (CN15) ...................................................................... 122 C.13 LCD inverter backlight connector (CN7) ....................................... 122 C.14 IR connector (CN27) .......................................................................... 123 C.15 CRT display connector (CN1) .......................................................... 123 C.
Tables PCM-9550FM/9550F/9550L Model Comparison Table ............................................. iii Table 2-1: Jumpers ...................................................................................................... 10 Table 2-2: Connector Assignments .............................................................................. 11 Table 2-3: CMOS clear (J3) ......................................................................................... 16 Table 2-4: J8: DOC-2000 address setting .........
Table C-18: 24-bit LCD display connector (CN14) .................................................. 125 Table C-19: 36-bit LCD display connector (CN9) .................................................... 126 Table C-20: Peripheral power connector (CN26) ...................................................... 127 Table C-21: CompactFlash Card Connector (CN30) ................................................ 127 Table C-22: ATX power feature connector (CN5) ....................................................
Figures Figure 1-1: PCM-9550 dimensions ............................................................................... 7 Figure 2-1: Locating jumpers ....................................................................................... 12 Figure 2-2: Locating connectors (component side) ...................................................... 13 Figure 2-3: Locating connectors (solder side) ..............................................................
CHAPTER 1 General Information This chapter gives background information on the PCM-9550F/FM/L.
1.1 Introduction The PCM-9550F/FM/L is an Intel low-power Pentium® MMX ™ 266 MHz processor single board computer (SBC) with audio controller, a PCI SVGA controller, a PCI 10/100Base-T Ethernet interface, and one PC/104-Plus expansion connector. The PCM9550F/FM/L’s design is based on the EBX form factor that provides support for PC/104 and PC/104-Plus module expansion.
1024 x 768 resolution @ 16.8 M colors with 4 MB display memory. Major on-board devices adopt PCI technology, to achieve outstanding computing performance when used with Intel® Pentium® processors. The PCM-9550F/FM (but not PCM-9550L) also supports TV-out (NTSC/PAL format) and video-in function (PCM-9550FM only) for multimedia applications. 1.
1.3 Specifications 1.3.1 Standard EBX SBC functions • CPU: Embedded Intel low-power Pentium MMX- 266 MHz • BIOS: AWARD 256KB Flash BIOS, supports Plug & Play, APM, Ethernet boot ROM, boot from CD-ROM, LS-120 • Chipset: Intel 430TX • Green function: APM 1.1 compliant • 2nd level cache: On-board 512 KB Pipeline Burst SRAM • RAM: One 168-pin DIMM socket accepts 32 ~ 256 MB SDRAM • Enhanced IDE interface: 2 enhanced IDE channels support up to 4 IDE devices.
• USB interface: Two USB connectors with fuse protection. Compliant with USB Spec. Rev. 1.10 • I/O bus expansion: Supports Mini-PCI socket for optional modem • PC/104-Plus: EBX form factor supports PC/104-Plus for ISA and PCI bus expansion. (PCM-9550L Model supports PC/104 only.) 1.3.2 PCI SVGA/flat panel interface • Chipset: C&T 69000 with 2 MB memory and optional C&T 69030 with 4 MB memory.
1.3.4 Audio function (PCM-9550F/9550FM only) • Chipset: ESS ES 1989 • Audio controller: AC97 Ver. 2.0 compliant interface, Multistream Direst Sound and Direct Sound 3D acceleration • Stereo sound: 8-bit full-duplex • Audio interface: Microphone in, Line in, CD audio in; Line out, Speaker L, Speaker R • Power: Accepts +12 V source for improved audio quality 1.3.
• Operating temperature: 0 ~ 60° C (32 ~ 140° F) • Size (L x W): 203 mm x 146 mm (8" x 5.75") • Weight: 0.7 kg (1.54 lb) (weight of total package) 1.
8 PCM-9550F/FM/L User's Manual
CHAPTER 2 Installation This chapter tells how to set up the PCM-9550F/FM/L hardware. It includes instructions on setting jumpers, and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installation procedure.
2.1 Jumpers The PCM-9550F/FM/L has a number of jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the board’s jumpers.
Table 2-2: Connector Assignments Label CN1 Function CRT display connector CN2 Video in/video out connector* CN3 Reserve for S-video connector* CN4 Reserve for composite connector* CN5 ATX feature connector CN6 Ethernet connector CN7 Backlight connector CN8 Main power connector CN 9 Ext.
2.
2.4 Locating connectors 2.4.
2.4.
2.5 Setting jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, connect the pins with the clip. To “open” a jumper, remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case, you would connect either pins 1 and 2 or 2 and 3.
2.6 CMOS clear (J3) Warning: To avoid damaging the computer, always turn off the power supply before setting “Clear CMOS.” Before turning on the power supply, set the jumper back to “3.0 V Battery On.” Table 2-3: CMOS clear (J3) *3.
2.7 Installing system memory (DIMMs) You are able to install memory ranging from 16 to 256 MB of DIMM onto your PCM-9550F/FM/L card. The card provides one 168-pin DIMM socket, which accepts 16, 32, 64, 128 or 256 MB 3.3 V power level EDO/synchronous DIMMs. 2.7.1 Installing DIMMs The procedure for installing DIMMs is described below. Please follow these steps carefully. The number of pins are different on either side of the breaks, so the module can only fit in one way.
2.8.1 Connecting the hard drive Connecting drives is done in a daisy-chain fashion. It requires one of two cables (not included in this package), depending on the drive size. 1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flatcable connector. 3.5" drives use a 1 x 44-pin to 2 x 40-pin connector. Wire number 1 on the cable is red or blue, and the other wires are gray. 1. Connect one end of the cable to CN16 or CN17.
2.9 Solid State Disk The PCM-9550F/FM/L provides a CompactFlash™ card socket and DiskOnChip socket for Solid state disk solutions. 2.9.1 CompactFlash (CN30) The CompactFlash card shares a secondary IDE channel which can be enabled/disabled via the Bios settings. 2.9.2 DiskOnChip 2000 Address setting (J8) The DiskOnChip address can be set using the table below.
2.10 Floppy drive connector (CN19) You can attach up to two floppy drives to the PCM-9550F/FM/L’s on-board controller. You can use any combination of 5.25” (360 KB and 1.2 MB) and/or 3.5” (720 KB, 1.44 MB, and 2.88 MB) drives. A 34-pin daisy-chain drive connector cable is required for a dual-drive system. On one end of the cable is a 34-pin flat-cable connector. On the other end are two sets of floppy disk drive connectors. Each set consists of a 34-pin flat-cable connector (usually used for 3.
2.11 Parallel port connector (CN21, CN22) Normally, the parallel port is used to connect the card to a printer. The PCM-9550F/FM/L includes a multi-mode (ECP/EPP/SPP) parallel port accessed via CN21 or CN22, and a 26-pin flat-cable connector. You will need an adapter cable if you use a traditional DB-25 connector. The adapter cable has a 26-pin connector on one end, and a DB-25 connector on the other.
2.13 Front panel connector (CN13) Next, you may want to install external switches to monitor and control the PCM-9550F/FM/L. These features are optional: install them only if you need them. The front panel connector (CN13) is an 8-pin male, dual in-line header. It provides connections for a speaker, hard disk access indicator, watchdog output, and an input switch for resetting the card. 2.13.1 Speaker The PCM-9550F/FM/L can drive an 8 ohm speaker at 0.5 watts.
2.14 Power connectors (CN24, CN8, CN26) 2.14.1 Peripheral power connector, -5 V, -12 V (CN26) Supplies secondary power to devices that require -5 V and -12 V. 2.14.2 Main power connector, +5 V, +12 V (CN8) Supplies main power to the PCM-5864/L (+5 V), and to devices that require +12 V. 2.14.3 CPU Fan power supply connector (CN24) Provides power supply to CPU cooling fan. Only present when +5 V and +12 V power is supplied to the board.
2.15 ATX power control connector (J4, CN5) 2.15.1 ATX feature connector (CN5) and soft power switch connector (J4) The PCM-9550F/FM/L can support an advanced soft power switch function, if an ATX power supply is used. To enable the soft power switch function: 1. Get the specially designed ATX-to-EBX power cable (PCM-9550F/FM/L optional item, part no. 1703200100) 2. Connect the 3-pin plug of the cable to CN5 (ATX feature connector). 3. Connect the power on/off button to J4.
2.16 IR connector (CN27) This connector supports the optional wireless infrared transmitting and receiving module. This module mounts on the system case. You must configure the setting through BIOS setup. 2.17 Audio interfaces (CN2, CN11) (PCM-9550F/9550FM only) The PCM-9550F/FM is equipped with a high-quality audio interface, which provides 16-bit CD-quality recording and playback as well as OPL3 compatible FM music. It is supported by all major operating systems. 2.17.
2.17.3 Audio power source setting (J7) The PCM-9550F/FM is designed to work with a single +5 V power supply. The audio interface can also function normally under single +5V power supply, but most audio controllers require an independent power source generated from a +12 V power supply. The independent power source avoids the noise from the other digital circuits. The PCM-9550F/FM’s audio interface can accept +12 V power to provide improved quality audio. This is done via J7.
2.18 COM port connector (CN20) The PCM-9550F/FM/L provides four serial ports (COM1, 3, 4: RS-232; COM2: RS-232/422/485) in one COM port connector. The COM port connector is a 40-pin, dual-inline, male header. It provides connections for serial devices (a mouse, etc.) or a communication network. You can find the pin assignments for the COM port connector in Appendix C. 2.18.1 COM2 RS-232/422/485 setting (J9) COM2 can be configured to operate in RS-232, RS-422, or RS485 mode. This is done via J9.
2.18.2 Share IRQ (PCM-9550F/9550FM only) The IRQ and the address range for COM1, 2, 3, 4 default are fixed. However, if you wish to disable the port or change these parameters later, you can do this in the system BIOS setup. The table below shows the settings for the PCM-9550F/FM’s serial ports.
Table 2-8: J10: COM1-4 RI settings Pins Com port RI Power setting 1-2 COM1 RI pin +5 V 3-4 COM1 RI pin +12 V 5-6 COM1 RI pin R I* 7-8 COM2 RI pin +5 V 9-10 COM2 RI pin +12 V 11-12 COM2 RI pin R I* 13-14 COM3 RI pin +5 V 15-16 COM3 RI pin +12 V 17-18 COM3 RI pin R I* 19-20 COM4 RI pin +5 V 21-22 COM4 RI pin +12 V 23-24 COM4 RI pin R I* Chapter 2 Installation 29
2.19 VGA interface connections The PCM-5864/L’s PCI SVGA interface can drive conventional CRT displays and is capable of driving a wide range of flat panel displays, including electroluminescent (EL), gas plasma, passive LCD and active LCD displays. The board has two connectors to support these displays, one for standard CRT VGA monitors and one for flat panel displays. 2.19.1 CRT display connector (CN1) CN1 is a 16-pin, dual-inline header used for conventional CRT displays.
2.19.4 LCD power setting The PCM-9550F/FM/L’s PCI SVGA interface supports 5 V and 3.3 V LCD displays that provide Vdd 5 V signal on CN14. 2.20 VGA/TV-Out function select (J1) The PCM-9550F/FM provides a TV-out function that is selected by configuring J1 as shown below. Table 2-9: VGA/TV-Out function select (J1) VGA TV 2.21 Video In/Out interfaces (CN2) (PCM-9550FM only) The PCM-9550FM board provides Video-in and Video-out (TVout) (CN2). They consist of a 14-pin dual-inline header respectively.
2. Run the appropriate installation software program, located in the utility disk. For NTSC format, the file is 55xntsc.exe, located in: Biscuit\9550F\Video.100\69000\TV-out\ For PAL format, the file is 55xpal.exe, located in: Biscuit\9550F\Video.
2.22 Ethernet configuration The PCM-9550F/FM/L is equipped with a high performance 32-bit PCI-bus Ethernet interface which is fully compliant with IEEE 802.3U 10/100Mbps CSMA/CD standards. It is supported by all major network operating systems. The medium type can be configured via the RSET8139.EXE program included on the utility disk. (See Chapter 3 for detailed information.) 2.22.
2.23 Watchdog timer configuration An on-board watchdog timer reduces the chance of disruptions which EMP (electro-magnetic pulse) interference can cause. This is an invaluable protective device for standalone or unmanned applications. Setup involves one jumper and running the control software (refer to Appendix A). 2.23.1 Watchdog timer action (J11) When the watchdog timer activates (CPU processing has come to a halt), it can reset the system or generate an interrupt on IRQ11.
2.24 USB connectors (CN15) The PCM-9550F/FM/L board provides two USB (Universal Serial Bus) ports which gives complete plug and play, and hot attach/ detach for up to 127 external devices. The USB interfaces comply with USB specification Rev. 1.0, and are fuse protected. The USB interface is accessed through one 5-pin flat-cable connector, CN15. You will need an adapter cable if you use a standard USB connector. The adapter cable has a 5-pin connector on one end and an USB connector on the other.
Figure 2-6: Digital opto Isolated output block diagram 36 PCM-9550F/FM/L User's Manual
2.25.1 Digital output programming Table 2-13: Digital output programming Output Address Bit Out 0 550 0 Out 1 550 1 Out 2 550 2 Out 3 550 3 Out 4 550 4 Out 5 550 5 Out 6 550 6 Out 7 550 7 2.25.2 Digital Input programming Table 2-14: Digital input programming Input Address Bit In-0 550 0 In-1 550 1 In-2 550 2 In-3 550 3 In-4 550 4 In-5 550 5 In-6 550 6 In-7 550 7 Note: The INPUT signal must be TTL compatible.
2.25.3 Isolated Digital Output (CN28) The PCM-9550F supports 2 isolated digital output via CN28.
CHAPTER 3 Software Configuration This chapter details the software configuration information. It shows you how to configure the card to match your application requirements. AWARD System BIOS is covered in Chapter 4.
3.1 Introduction The PCM-9550F/FM/L system BIOS and custom drivers are located in a 256 Kbyte, Flash ROM device, designated U18. A single Flash chip holds the system BIOS, VGA BIOS and network Boot ROM image. The display can be configured via CMOS settings. This method minimizes the number of chips and difficulty of configuration. To set different types of LCD panels, please choose “panel type” from the “integrated peripherals” menu in CMOS setup. 3.2 Connections for five standard LCDs 3.2.
3.2.
3.2.
3.2.
3.2.
3.3 Ethernet software configuration The PCM-9550F/FM/L’s on-board Ethernet interface supports all major network operating systems. To configure the medium type, to view the current configuration, or to run diagnostics, do the following: 1. Power the PCM-9550F/FM/L on. Make sure that the RSET8139.EXE file is located in the working drive. 2. At the prompt, type RSET8139.EXE and press . The Ethernet configuration program will then be displayed. 3.
46 PCM-9550F/FM/L User's Manual
CHAPTER 4 Award BIOS Setup This chapter describes how to set BIOS configuration data.
4.1 System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. With non-fatal errors, the system can usually continue the boot sequence .
4.2 AWARD BIOS setup Award’s BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM, so that it retains the Setup information when the power is turned off. 4.2.1 Entering setup Power on the computer and press immediately. This will allow you to enter Setup.
4.2.2 Standard CMOS setup When you choose the STANDARD CMOS SETUP option from the INITIAL SETUP SCREEN menu, the screen shown below is displayed. This standard Setup menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Once a field is highlighted, online help information is displayed at the bottom left of the Menu screen.
4.2.3 BIOS features setup By choosing the BIOS FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9550F/FM/L.
4.2.4 Chipset features setup By choosing the CHIPSET FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9550F/FM/L.
4.2.5 Power management setup By choosing the POWER MANAGEMENT SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9550F/FM/L.
4.2.6 PnP/PCI configuration By choosing the PnP/PCI CONFIGURATION option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9550F/FM/L.
4.2.7 Integrated peripherals By choosing the INTEGRATED PERIPHERALS option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9550F/FM/L. By default, the PANEL TYPE supports an 18-bit 640 x 480 TFT LCD panel display.
4.2.8 Load BIOS defaults LOAD BIOS DEFAULTS loads the default system values directly from ROM. If the stored record created by the Setup program becomes corrupted (and therefore unusable), these defaults will load automatically when you turn the PCM-9550F/FM/L on.
4.2.9 Change password To change the password, choose the PASSWORD SETTING option form the Setup main menu and press . 1. If the CMOS is bad or this option has never been used, a default password is stored in the ROM. The screen will display the following messages: Enter Password: Press . 2. If the CMOS is good or this option has been used to change the default password, the user is asked for the password stored in the CMOS.
4.2.10 Auto detect hard disk The IDE HDD AUTO DETECTION utility can automatically detect the IDE hard disk installed in your system. You can use it to selfdetect and/or correct the hard disk type configuration. 4.2.11 Save & exit setup If you select this option and press , the values entered in the setup utilities will be recorded in the chipset’s CMOS memory. The microprocessor will check this every time you turn your system on, and compare this to what it finds as it checks the system.
CHAPTER 5 PCI SVGA Setup • Introduction • Installation of SVGA driver for - Windows 3.
5.1 Introduction The PCM-9550F/FM/L has an on-board PCI flat panel/VGA interface. The specifications and features are described as follows: 5.1.1 Chipset The PCM-9550F/FM/L uses a C&T 6900/69030 chipset for its PCI/SVGA controller. It supports many popular LCD, EL, and gas plasma flat panel displays, as well as conventional analog CRT monitors. The 6900/69030 VGA BIOS supports monochrome LCD, EL, color TFT, and STN LCD flat panel displays.
CT.COM: Enables CRT display only FP.COM: Enables panel display only SM.COM: Enables both displays simultaneously 5.2 Installation of SVGA driver Complete the following steps to install the SVGA driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your PCM-9550F/FM/L. Important: The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which then appear on your screen.
5.2.1 Installation for Windows 95/98 1. Select "Start", "Settings", "Control Panel", "Display", "Settings". Then click on "Advanced Properties". 2. Choose the "Adaptor" label. Press "Change...
3. Press the "Have Disk" button. 4. Insert the utility disk into the floppy disk drive. Type: "D:\Biscuit\9550F\VGA\69000\Win95" Press "OK". 5. Select the highlighted item. Click the "OK" button.
6. C&T69000/69030 appears in the adapter label. Click on the "Apply" button. 7. Press "Yes" to reboot. 8. Repeat Step 1. The "CHIPS" label appears in the "Display". Adjust resolution and color.
9. Click the "CHIPS" label. Adjust the refresh rate and display type. Press "OK" to exit. 10. Press "Yes" to set the monitor type. 11. Select "Standard", "Super VGA 800 x 600". or "XGA". Then press the "OK" button.
12. Choose "Restart" to reboot. End Note: 1. In step 4, for Windows 98, the path is: "D:\Biscuit\9550F\VGA\69000\Win98\" 2.
5.2.2 Installation for Windows 3.1 1. Insert the utility disk into the floppy disk drive. Select "File" in the Program Manager. Click "Run" and type: "D:\Biscuit\9550F\VGA\69000\Win31\Setup.exe". 2. Choose the language you want to use during installation. 3. Select the highlighted item. Press "ENTER".
4. Press "ENTER" to install all resolutions. 5. Type the path of the operating system. 6. When installation is complete, reboot the system. You will see the "ChipsCPL" icon in the control panel.
7. Double click "ChipsCPL". Adjust the screen size, color and refresh rate to your preferences. 5.3 Further information For further information about PCI/SVGA installation in your PCM-9550F/FM/L, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: Asillion website: www.asilian.com Advantech websites: www.advantech.com www.advantech.
5.3 Further information For further information about PCI/SVGA installation in your PCM-9550F/FM/L, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: Asillion website: www.asilian.com Advantech websites: www.advantech.com www.advantech.
5.2.3 Installation for Windows NT 1. Select "Start", "Settings", "Control Panel", then double click the "Display" icon. 2. Choose the "Settings" label. Then press the "Display Type" button.
3. Press the "Change...." button. 4. Click the 'Have Disk..." button. 5. Insert the utility disk into the floppy disk drive. Type: "D:\Biscuit\9550F\VGA\69000\Winnt" Press the "OK" button.
6. Select the highlighted item. Press the "OK" button. 7. Press "Yes" to proceed. 8. Press "OK" to reboot.
9. Repeat Step 1 to select the "Settings" label. Adjust resolution and color. Click "Test" to see the result. Click "OK" to save the setting.
5.3 Further information For further information about PCI/SVGA installation in your PCM9550F/FM/L, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: Asillion website: www.asilian.com Advantech websites: www.advantech.com www.advantech.
76 PCM-9550F/FM/L User's Manual
CHAPTER 6 Video (PCM-9550FM only) • Introduction • Installation of video capture driver for Windows 95/98
6.1 Introduction The PCM-9550FM's on-board Video-in and Video-out (TV-out) provides NTSC and PAL video standards. Video-in uses Philips SAA 7111A video input processor. TV-out uses CHRONTEL CH7002. Video-in/out provides a 14-pin header connector for RCA Yellow jack for composite video in and TV out. Alternatively, an optional cable kit provides an S-Video connector. 6.2 Installation of video driver Before installing the Video-in driver, please take note of the procedures detailed below.
6.2.1 Installation for Windows 95/98 1. Select "Start," "Settings," "Control Panel," "Add New Hardware." Click "Next" to begin installing the new device. Click "Next" to continue. 2. Choose "No, I want to select hardware...." Click "Next.
3. Select "Sound, video,..." Click "Next" 4. Click "Have Disk...
5. Insert the disk into the CD-ROM drive. Type the correct path: D:\Biscuit\9550FM\VGA\69000\Capture" Click the "OK" button. 6. Select the highlighted item.
7. Click "Finish" to complete. End Note: Before you restart Windows, insert the following pcvideo.ini and ctmmhw.
6.3 Installation of Chips-TV utility This utility is for demonstration only. 1. Select "Start," "Run." Type the correct path: "D:\Biscuit\9550FM\VGA\69000|Chips-TV\Setup.exe" Click "OK" 2.
3. Click "Continue" 4. Click "OK" to complete the setup.
CHAPTER 7 Audio (PCM-9550F/9550FM only) • Introduction • Installation of audio driver for Windows 95/98/NT
7.1 Introduction The PCM-9550F/FM on-board audio interface provides high-quality stereo sound and FM music synthesis (ESFM) by using the ES1373 audio controller from Creative Technology Ltd. The audio interface can record, compress, and play back voice, sound, and music with a built-in mixer control. The PCM-9550F/ FM's on-board audio interface also supports the Plug and Play (PnP) standard and provides PnP configuration for audio, FM, and MPU-104 logical devices. It is compatible with AC97 version 2.
7.2.
1. a. Select "Start", "Run" b. Type the correct path" D:\Biscuit\9550F\Audio\Win95\ c. Click the "OK" button 2. a. Click "Yes" to accept the agreement b.
3. a. Click "Next" to continue b. Follow the procedure which appears on your screen 4.
90 PCM-9550F/FM/L User's Manual
CHAPTER 8 PCI Bus Ethernet Interface This chapter provides information on Ethernet configuration.
8.1 Introduction The PCA-9550F/FM/L is equipped with a high performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T and 10Base-T compatible. The medium type can be configured via the RSET8139.exe program included on the utility disk. The Ethernet port provides a standard RJ-45 jack via an optional wiring kit.
8.2.2 Installation for Windows 95/98 1.a. b. 2.
3. Select the "Adapter" item to add the Ethernet card. 4. Click "Have Disk" to install the driver. 5.a. Insert the Utility CD ROM b. Fill in the correct path D:\Biscuit\9550F\LAN\8139C\WIN98 c.
6.a. b. 7.a. b. Choose the "Realtek RTL8139(A/B/C/8130) PCI Fast Ethernet". Click "OK" Make sure the configurations of the relative items are set correctly. Click "OK" to reboot.
8.2.3 Installation for Windows NT 1.a. b. 2.a. b.
3. Click "Select from list..." 4. Click "Have Disk" 5.a. Insert the Utility CD ROM b. Fill in the correct path D:\Biscuit\9550F\LAN\8139C\winnt4 c.
6.a. b. 7.
8.a. b. 9.a. b.
10. Click "Next" to continue setup 11. Click "Next" to start the network 8.3 Further information 100 Realtek website: www.realtek.com.tw Advantech websites: www.advantech.com www.advantech.com.tw Intel website: www.intel.
APPENDIX A Programming the Watchdog Timer The PCM-9550F/FM/L is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environments.
A.1 Programming the watchdog timer In order to program the watchdog timer, you must write a program which writes I/O port address 443 (hex). The output data is a value of time interval. The value range is from 01 (hex) to 3E (hex), and the related time interval is 1 sec. to 62 sec. Data 01 02 03 04 3E Time 1 2 3 4 Interval sec. sec. sec. sec. . . . 62 sec. After data entry, your program must refresh the watchdog timer by rewriting the I/O port 443 (hex) while simultaneously setting it.
The following example shows how you might program the watchdog timer in BASIC: 10 20 30 40 50 60 70 80 1000 . . . 1070 2000 . . .
104 PCM-9550F/FM/L User's Manual
APPENDIX B Installing PC/104Plus Modules This appendix gives instructions for installing PC/104- Plus modules.
B.1 Installing PC/104 modules The PCM-9550F/FM/L's PC/104 connectors give you the flexibility to attach PC/104+ modules. Installing these modules on the PCM-9550F/FM/L is quick and simple. The following steps show how to mount the PC/104+ modules: 1. Remove the PCM-(550F/M from your system, paying particular attention to the safety instructions already mentioned above. 2. Make any jumper or link changes required to the CPU card now.
P C /104 M ounting S upport Fem ale P C M -5864/L M ale P C /104 m odule Figure B-1: PC/104+ module mounting diagram Figure B-2: PC/104+ module dimensions (mm) (±0.
108 PCM-9550F/FM/L User’s Manual
APPENDIX C Pin Assignments This appendix contains information of a detailed or specialized nature.
C.1 CPU fan power connector (CN24) 1 2 3 Table C-1: CPU fan power connector (CN24) Pin Signal 1 +5 V 2 GND 3 +12 V C.
C.
C.
C.5 Main power connector (CN8) Table C-5: Main power connector (CN8) Pin 1 +5 V 2 GND 3 GND 4 +12 V 5 N.C.
C.
C.
C.
PC/104+ connectors (cont.
Table C-9: PC/104+ Bus signal assignments (CN18) Pin Number Signal (CN18) RowA RowB RowC Signal (CN18) RowD 1 GND/5V/KEY RESERVED +5 AD00 2 VI/O AD02 AD01 +5V 3 AD05 GND AD04 AD03 4 C/BE0* AD07 GND AD06 5 GND AD09 AD08 GND 6 AD11 VI/O AD10 M66EN 7 AD14 AD13 GND AD12 8 +3.3V C/BE1* AD15 +3.3V 9 SERR* GND SB0* PAR 10 GND PERR* +3.3V SDONE 11 STOP* +3.3V LOCK* GND 12 +3.3V TRDY* GND DEVSEL* 13 FRAME* GND IRDY* +3.3V 14 GND AD16 +3.
C.
C.10 Parallel port connector (CN21, CN22) Table C-11: Parallel port connector (CN21, CN22) Pin Signal Pin Signal 1 STROBE* 2 AUTOFD* 3 D0 4 ERR 5 D1 6 INIT* 7 D2 8 SLCTINI* 9 D3 10 GND 11 D4 12 GND 13 D5 14 GND 15 D6 16 GND 17 D7 18 GND 19 ACK* 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT 26 N/C * low active Note: CN21 applies to PCM-9550F/9550FM only.
C.
C.12 USB connector (CN15) Table C-13: USB connector (CN15) Pin Signal Pin Signal 1 +5 V 2 +5 V 3 UV- 4 UV- 5 UV+ 6 UV+ 7 GND 8 GND 9 Chassis GND 10 N/C C.
C.14 IR connector (CN27) Table C-15: IR connector (CN27) Pin Signal 1 V CC 2 FIR REceive 3 IR REceive 4 GND 5 FIR/IR Transmit C.
C.
C.
C.18 36-bit LCD display connector (CN9) Table C-19: 36-bit LCD display connector (CN9) Pin Signal Pin Signal 1 GND 2 GND 3 P24 4 P25 5 P26 6 P27 7 P28 8 P29 9 P30 10 P31 11 P32 12 P33 13 P34 14 P35 15 GND 16 GND 17 N/C 18 N/C 19 N/C 20 N/C Note: 126 The model number of the CN19 socket is DF13A-20DP-1.25V (Hirose Electric Co., Ltd.
C.19 Peripheral power connector (CN26) Table C-20: Peripheral power connector (CN26) Pin Function 1 -5 V 2 GND 3 -12 V C.
17 A03 18 A02 19 A01 20 A00 21 D00 22 D01 23 D02 24 -IOCS16 25 *CD2 26 -CD1 27 D11 28 D12 29 D13 30 D14 31 D15 32 -CS1 33 *VS1 34 -IORD 35 *IOWR 36 -WE 37 INTRQ 38 +5 V 39 *CSEL 40 -VS2 41 *RESER 42 IORDY 43 *INPACK 44 -REG 45 *DASP 46 -PDIAG 47 D08 48 D09 49 D10 50 GND * low active C.21 ATX power feature connector (CN5) Table C-22: ATX power feature connector (CN5) 128 Pin Signal 1 5VSB (Stand by voltage) 2 GND 3 PS.
C.22 Digital I/O (CN23) Table C-23: Digital I/O (CN23) Pin Pin 1 DOO 2 DO1 3 DO2 4 DO3 5 DO4 6 DO5 7 DO6 8 DO7 9 GND 10 GND 11 DI0 12 DI1 13 DI2 14 DI3 15 DI4 16 DI5 17 DI6 18 DI7 19 GND 20 GND C.23 Isolated 2 Digital Out (CN28) Table C-24: Isolated Digital Out (CN28) Pin Pin 1. VIO0 3. VIO1 2. DO0 4.
C.24 COM port connector (CN20) 39 37 .... 3 1 40 38 ....
APPENDIX D System Assignments This appendix contains information of a detailed or specialized nature.
D.1 System I/O ports Table D-1: System I/O ports Addr.
D.2 1st MB memory map Table D-2: 1st MB memory map Addr. range (Hex) F000h - FFFFFh **DC000h - EFFFFh *CC000h - DBFFFh C0000h - CBFFFh B8000h - BFFFFh B0000h - B7FFFh A0000h - AFFFFh 00000h - 9FFFFh Device System ROM Unused Ethernet ROM Expansion ROM (for VGA BIOS) CGA/EGA/VGA text Unused EGA/VGA graphics Base memory * If Ethernet boot ROM is enabled ** E0000 - EFFFF is reserved for Pentium® POST D.
D.
APPENDIX E Optional Extras for the PCM-9550F/FM/L
E.1 PCM-10586-5000/PCM-10586-5M00 cable kit for PCM-9550F and PCM-9550FM The PCM-9550F/FM/L requires several cables for normal operation. You can make them yourself or purchase an optional cable kit assembly, which includes the following: PCM-10586-5000 cable kit for PCM-9550 F PCM-10586-5M00 cable kit for PCM-9550 FM PCM-10586-5L00 cable kit for PCM-9550 L Part No. Cable Description PCM-9550 Connector Terminating Connector 1701440350 2.5" and 1.
E.2 Optional LCD cables for 9.4" MONO, 10.4" TFT LCD panel (CN14) Optional LCD cables for 9.4" MONO, 10.4" TFT LCD panel Part no. Cable description Panel type 1700090501 Cable DF9 (2 mm) 50 cm Toshiba LTM10C042 1700090403 Cable DF9 (2 mm) 40 cm Sharp LM64183P Sharp LM64P89 1703440151 Wire 30P/44P 15 cm Toshiba LTM12C275A E.3 Optional USB cable (CN16) Optional USB cable (2-channel) Part no: 1703100260 E.4 ATX Power Control Cable (CN5) part no.:1703200100 E.
138 PCM-9550F/FM/L User's Manual
APPENDIX Mechanical Drawings F
F.
F.
142 PCM-9550F/FM/L User's Manual
