PCM-3523,PCM-3523S User’s Manual 0 PCM-3523(S) User’s Manual PCM-3523(S) User’s Manual 1
Copyright Notice Packing Set This document is copyrighted, 1997. All rights are reserved. The original manufacturer reserves the right to make improvements to the products Before you begin installing PCM-3523, PCM-3523S card, please make described in this manual at any time without notice. sure that the following materials have been shipped.
Contents Chapter 1 General Information … … .… … … … … … … … .6 Appendix A Installing PC/104 Modules… … … … … … … .36 Appendix B Pin Assignments… … … … … … … … … … … … ...40 Introduction… ..… … … ..… … … … ..… … … .… .… … … … … ...7 PC/104 connectors ( J1,J2)… … … ..… … … … … … … … … … ....41 Product Highlights… … … … … .… … … .… … … … … … … … ..8 DB15 connector (CN1,CN3)… … .… … … … … … … … … … … ..4 Features … … … … … … … … … …….………………….…. … .
CHAPTER 1 General Information This chapter gives background information on the PCM-3523. You can find out: Ü Introduction Ü Product Highlight Ü Features Ü Specification Ü Board Layout Introduction The PCM-3523(S) converts RGB video and sync from a standard VGA source into broadcast quality NTSC and PAL video. Composite and S-Video outputs are compliant with SMPTE-170M and CCIR-656 specification. A fully integrated 3-line adaptive flicker filter provides three selectable operating modes.
Product Highlights Ü 3-Channel 9-bit output D/A converters Ü PC/104 Embedded-PC Module.
Physical and Environmental Specifications Board Layout Length: 3.6 inches Width: 3.8 inches Operating Temperature: 32 to 140 °F (0 to 60 °C) Humidity (operating): 5% to 95% Non-Condensing Power Requirement: 5.25 to 4.
CHAPTER 2 Hardware Installation This chapter tells how to set up the PCM-3523(S) hardware, including instruction on setting jumpers and connecting external devices. Be sure to read all the safety precautions before you begin the installation procedure.
standard. TD0-1 select one of four sets of parameters to set up Setting Jumpers the encoder. Frames rate of the graphics source must be twice the frame rate of the selected video standard. Refer to table 4. PAL800 Resolution Select for PAL. Sets number of samples per VGA line. Refer to table 4. BLK Blank Screen Generator. When close to OFF, the color selected by BLUE is displayed on the screen.
VGAHS& CVIDEN VGAVS CN4 VGA output (16 pin box header) S-Video CN5 S-Video output. (4-pin mini DIN) Composite Video SVIDEN X OFF YES Active X CN6 S-Video output. (5-pin header) OFF X YES X Active CN7 Composite video output. (RCA jack) ON ON X Blank Blank CN8 Composite video output. (3-pin header) OFF OFF NO Blue Blue CN9 External video input. (RCA jack) CN10 External video input. (3-pin header) Table 4.
as below sequence.
Locating Connectors Locating Switches POS-D POS-R FILTER CN3 CN4 CN1 CN2 CN9 CN5 CN6 CN10 CN7 CN8 J1 20 PCM-3523(S) User’s Manual J2 PCM-3523(S) User’s Manual 21
DPM Closed to OFF TD0 Closed to OFF Always completely disconnect the power cord from your TD1 Closed to ON chassis whenever you are working on it. Do not make PAL800 Closed to ON connections while the power is on because the sudden BLK Closed to ON rush BLUE Closed to OFF PWRDN Closed to OFF SVIDEN Closed to OFF CVIDEN Closed to OFF Safety Precautions Warning! of power components.
CHAPTER 3 Installation for Win 95 and Win3.1 Introduction The PCM-3523 driver is supplied on one floppy disk. Installing the Driver The supplied software contains a Windows screen control utility, Wscrctrl.exe. Use the File Manager under your Windows 3.1 or run in Ü Introduction Windows 95 Start Menu to setup this utility. To install driver on your system, please run setup.exe file. The software will guide you through the Ü Installing the driver 24 PCM-3523(S) User’s Manual entire installation.
1. The following dialog box appears when you run the setup.exe in Windows. To proceed with the installation , choose the “continue” 2. The next dialog box appears. Then choose the standard TV system you needed. Button or press “ENTER”.
3. After choosing your TV system, following dialog box appears. Then decide the directory you want to install in your hard disk. 28 PCM-3523(S) User’s Manual 4. After choosing the directory. The setup program will create a Screen Control Icon in your Windows system.
5. The setup program will copy the files to the Windows system. 6. The setup program will create the Screen Control Icon in Windows system.
7. The installation is completed. 8. After installation is completed, the screen will show the attention for Windows 95 Users.
9. The next step will show the SMPTE color chart on your TV screen 10. Installation is completed. when you restart your windows program.
Installing PC/104 Modules APPENDIX A Installing PC/104 Modules This appendix gives instructions for installing PC/104 Modules The CPU card’s PC/104 connectors give you the flexibility to attach PC/104 expansion modules. These modules perform the functions of traditional plug-in expansion cards, but save space and valuable slots.
38 PCM-3523(S) User’s Manual PCM-3523(S) User’s Manual 39
PC/104 Connectors (J1, J2) APPENDIX B Pin Assignments This appendix contains information of a detailed or specialized nature.
DB15 Connector (CN1,CN3) Pin Number Signal Pin Number Singal 1 RED 2 N.C. 3 GREEN 4 GND 5 BLUE 6 N.C. 7 N.C. 8 N.C 9 GND 10 VGAHS 11 GND 12 VGAVS 13 GND 14 N.C. 15 GND 16 N.C.
