User Manual PCIE-1753 96-ch Digital I/O PCI Express Card
Copyright The documentation and the software included with this product are copyrighted 2013 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure.
Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
18. The equipment does not work well, or you cannot get it to work according to the user's manual. 19. The equipment has been dropped and damaged. 20. The equipment has obvious signs of breakage. 21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. 22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
PCIE-1753User Manual vi
Contents Chapter 1 Overview...............................................1 1.1 1.2 1.3 1.4 1.5 1.6 Introduction ............................................................................................... 2 Features .................................................................................................... 2 Applications............................................................................................... 3 Installation Guide ........................................................
PCIE-1753 User Manual viii
Chapter 1 Overview 1
1.1 Introduction The PCIE-1753 is a 96-ch DI/O card with PCI Express bus. It provides 96 channel of parallel digital input/output compatible with 5V/TTL. It emulates mode 0 of the 8255 PPI chip, but the buffered circuits offer a higher driving capability than the 8255. The I/O channels are divided into twelve 8-bit ports. Each port can be divided into two nibbles (bit 0 ~ 3 belongs to low nibble, while bit 4 ~ 7 belongs to high nibble). You can configure each nibble as either input or output via software.
1.3 Applications Industrial AC/DC I/O devices monitoring and control Relay and switch monitoring and control Parallel data transfer Sensing the signals of TTL, DTL, CMOS logic Driving indicator LEDs 1.
1.6 Accessories Advantech offers a complete set of accessory products to support the PCIE-1753 card. These accessories include: Wiring Cable The PCL-10268 shielded cable is specially designed for PCIE-1753 cards to provide high resistance to noise. To achieve better signal quality, the signal wires are twisted in such a way as to form a “twisted-pair cable”, reducing cross-talk and noise from other signal sources.
Chapter 2 2 Hardware Installation
2.1 Installation This chapter gives users a package item checklist, proper instructions about unpacking and step-by-step procedures for both driver and card installation. 2.2 Unpacking After receiving your PCIE-1753 package, please inspect its contents first. The package should contain the following items: PCIE-1753 card Companion CD-ROM User’s Manual The PCIE-1753 card harbors certain electronic components vulnerable to electrostatic discharge (ESD).
We recommend you to install the driver before you install the PCIE-1753 card into your system, since this will guarantee a smooth installation process. The Advantech device driver installation for the PCIE-1753 card is included on the companion CD-ROM that is shipped with your DA&C card package, or you can download it from Advantech official website. Note! Make sure you have installed the driver first before you install the card.
After the PCIE-1753 card is installed, you can verify whether it is properly installed on your system through the Device Manager: 1. Access the Device Manager through Control Panel/System/Device Manager. 2. The device name of the PCIE-1753 should be listed on the Device Manager tab as follows. Figure 2.1 Device Manager Note! If your card is properly installed, you should see the device name of your card listed on the Device Manager tab.
Chapter 3 3 Signal Connections
3.1 Overview Maintaining signal connections is one of the most important factors in ensuring that your application system is sending and receiving data correctly. A good signal connection can avoid unnecessary and costly damage to your PC and other hardware devices. This chapter provides useful information about how to connect input and output signals to the PCIE-1753 via the I/O connector. 3.2 Switch and Jumper Settings Figure 3.
Table 3.1: Summary of Jumper Settings Jumper Name Function Description Load default after reset JP1 Keeps the last status after reset (enabled) Table 3.
Table 3.
PCIE-1753 Pin Assignments Pin Description P0_0-7 I/O pins of Port 0 P1_0-7 I/O pins of Port 1 P2_0-7 I/O pins of Port 2 P3_0-7 I/O pins of Port 3 P4_0-7 I/O pins of Port 4 P5_0-7 I/O pins of Port 5 P6_0-7 I/O pins of Port 6 P7_0-7 I/O pins of Port 7 P8_0-7 I/O pins of Port 8 P9_0-7 I/O pins of Port 9 P10_0-7 I/O pins of Port 10 P11_0-7 I/O pins of Port 11 13 GND Ground VCC +5V voltage output (0.5 A max.) PCIE-1753 User Manual Signal Connections Name Chapter 3 3.
TTL Digital Input/Output The PCIE-1753 has 96 TTL-level digital inputs and outputs. The following figure shows connections to exchange digital signals with other TTL devices: If you want to receive an OPEN/SHORT signal from a switch or relay.
Appendix A Specifications A
A.1 Specifications A.1.1 PCIE-1753 Digital Input Channels 96 (shared with output) Compatibility 5V/TTL Input Voltage Interrupt Capable Channels Logic 0: 0.8 V max Logic 1: 2 V min 12 Digital Output Channels 96 (shared with output) Compatibility 5V / TTL Output Voltage Output Capability Logic 0: 0.4 V max Logic 1: 2.4 V min Sink: 0.4 V @ 24mA Source: 2.4 V @ 15mA General Bus Type PCI Express I/O Connectors 1x100-pin SCSI female connector Dimensions ( LxH ) 167.7 mm x 100 mm (6.6" x 3.
Appendix B Block Diagram B
B.
Appendix B Block Diagram PCIE-1753 User Manual 19
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
