User Manual PCIE-1730 32-ch Isolated Digital I/O PCI Express Card
Copyright The documentation and the software included with this product are copyrighted 2012 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure.
Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
18. The equipment does not work well, or you cannot get it to work according to the user's manual. 19. The equipment has been dropped and damaged. 20. The equipment has obvious signs of breakage. 21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. 22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
PCIE-1730 User Manual vi
Contents Chapter Chapter Chapter 1 Overview...............................................1 1.1 1.2 1.3 1.4 1.5 1.6 Introduction ............................................................................................... 2 Features .................................................................................................... 2 Applications............................................................................................... 3 Installation Guide ......................................
PCIE-1730 User Manual viii
Chapter 1 Overview 1
1.1 Introduction The Advantech PCIE-1730 is a 32-channel isolated digital input/output card for the PCI Express bus. The PCIE-1730’s isolated digital input channels are ideal for digital input in noisy environments or with floating potentials. The following sections of this chapter will provide further information about features, installation guide, together with some brief information on software and accessories for the PCIE-1730 card. 1.
Note! For detailed specifications of the PCIE-1730, refer to Appendix A, Specifications. 1.3 Applications Industrial ON/OFF control Switch status sensing BCD interfacing Digital I/O control Industrial and lab automation Laboratory & Education 1.
1.5 Software Overview Advantech offers device drivers, SDKs, third-party driver support and application software to help fully exploit the functions of your PCIE-1730 card. All these software packages are available on the companion CD-ROM or you can browse Advantech website to get the latest update: http://www.advantech.com/. 1.6 Accessories Advantech offers a complete set of accessory products to support the PCIE-1730 card.
Chapter 2 2 Hardware Installation
2.1 Installation This chapter gives users a package item checklist, proper instructions about unpacking and step-by-step procedures for both driver and card installation. 2.2 Unpacking After receiving your PCIE-1730 package, please inspect its contents first. The package should contain the following items: PCIE-1730 card Companion CD-ROM User’s Manual The PCIE-1730 card harbors certain electronic components vulnerable to electrostatic discharge (ESD).
We recommend you to install the driver before you install the PCIE-1730 card into your system, since this will guarantee a smooth installation process. The Advantech device driver installation for the PCIE-1730 card is included on the companion CD-ROM that is shipped with your DA&C card package. 2.4 Hardware Installation Make sure you have installed the driver first before you install the card.
After the PCIE-1730 card is installed, you can verify whether it is properly installed on your system through the Device Manager: 1. Access the Device Manager through Control Panel/System/Device Manager. 2. The device name of the PCIE-1730 should be listed on the Device Manager tab as follows. Figure 2.1 Device Manager Note! If your card is properly installed, you should see the device name of your card listed on the Device Manager tab.
Chapter 3 3 Signal Connections
3.1 Overview Maintaining signal connections is one of the most important factors in ensuring that your application system is sending and receiving data correctly. A good signal connection can avoid unnecessary and costly damage to your PC and other hardware devices. This chapter provides useful information about how to connect input and output signals to the PCIE-1730 via the I/O connector. 3.2 Switch and Jumper Settings Figure 3.1 Card Connector, Jumper and Switches Table 3.
PCIE-1730 Pin Assignments CN1 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 IDO 1 IDO 3 IDO 5 IDO 7 IDO 9 IDO 11 IDO 13 IDO 15 EGND NC IDI 0 IDI 2 IDI 4 IDI 6 IDI 8 IDI 10 IDI 12 IDI 14 ECOM0 ECOM0 CN3 DO 0 DO 2 DO 4 DO 6 DO 8 DO 10 DO 12 DO 14 GND NC 1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 IDI 1 IDI 3 IDI 5 IDI 7 IDI 9 IDI 11 IDI 13 IDI 15 ECOM1 ECOM1 CN4 2 4 6 8 10 12 14 16 18 20 DO 1 DO 3 DO 5 DO 7 DO 9 DO 11 DO 13 DO 15 GND NC DI 0 DI 2 DI 4 DI 6 DI 8
TTL-level Digital Input/Output The PCIE-1730 has 16 TTL-level digital inputs and 16 TTL-level digital outputs. The following figure shows connections to exchange digital signals with other TTL devices: Figure 3.2 TTL-level DI/O Connection If you want to receive an OPEN/SHORT signal from a switch or relay. See the figure below: Figure 3.
External Internal Signal Connections IDI0 Wet contact ECOM Isolated Circuit IDI1 Dry Contact EGND Figure 3.4 Isolated DI Connection Isolated Digital Output If the external voltage source (5~40 V) is connected to each isolated output channel (IDO) and its isolated digital output turns on (500 mA max./ch), the card's current will sink from the external voltage source. CN5 provides two EGND pins for IDO connection.
PCIE-1730 User Manual 14
Appendix A Specifications A
A.1 Specifications A.1.1 PCIE-1730 Isolated Digital Input Input Channels 16 Input Voltage Logic 0: 3 V max. (0 VDC min.) Logic 1: 10 V min. (30 VDC max.) 12 VDC @ 3.18 mA Input Current 24 VDC @ 6.71 mA Interrupt Capable Ch.
Appendix B Block Diagram B
B.
Appendix B Block Diagram PCIE-1730 User Manual 19
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
