User manual
Table Of Contents
- Chapter 1 Introduction
- Chapter 2 Hardware Configuration
- 2.1 Initial Inspection
- 2.2 Jumper and Switch Locations
- Figure 2.1: PCI-1601A/B Silk Screen
- Figure 2.2: PCI-1601AU/BU Silk Screen
- Figure 2.3: PCI-1602A/B Silk Screen
- Figure 2.4: PCI-1602AU/BU Silk Screen
- Figure 2.5: PCI-1602UP Silk Screen
- Figure 2.6: PCI-1603 Silk Screen
- Figure 2.7: PCI-1604UP Silk Screen
- Figure 2.8: PCI-1610A/B Silk Screen
- Figure 2.9: PCI-1610CU Silk Screen
- Figure 2.10: PCI-1610AUP/UP Silk Screen
- Figure 2.11: PCI-1610AJP Silk Screen
- Figure 2.12: PCI-1611U Silk Screen
- Figure 2.13: PCI-1612A/B Silk Screen
- Figure 2.14: PCI-1612AU/U Silk Screen
- Figure 2.15: PCI-1612CU Silk Screen
- Figure 2.16: PCI-1620A/B Silk Screen
- Figure 2.17: PCI-1620AU/U Silk Screen
- Figure 2.18: PCI-1622CU Silk Screen
- 2.3 Jumper Settings
- 2.3.1 How to Set Jumpers
- 2.3.2 Default Settings
- 2.3.3 Mode Selection by Jumper/DIP Settings
- Figure 2.21: PCI-1612 Series RS-232/422/485 Selection
- Figure 2.22: RS-422/485 Selection by Jumper Setting
- Figure 2.23: PCI-1603 RS-232 Mode Jumper Setting
- Figure 2.24: PCI-1603 Current-loop Mode Jumper Setting
- Figure 2.25: Active Mode Jumper Setting
- Figure 2.26: Passive Mode Jumper Setting
- Figure 2.27: Resistor Selection
- 2.4 Card Installation
- Chapter 3 Driver Setup & Installation
- Chapter 4 ICOM Tools
- Chapter 5 Pin Assignments and Wiring
83 Chapter 5
Table 5.16: PCI-1611U female DB37 on bracket
Pin RS-422 RS-485 Pin RS-422 RS-485
1- - 20 3_CTS- -
2 3_TxD- 3_Data- 21 3_RxD- -
3 3_GND 3_GND 22 3_RTS- -
4 3_CTS+ - 23 3_RTS+ -
5 3_TxD+ 3_Data+ 24 3_RxD+ -
6 4_CTS- - 25 4_TxD- 4_Data-
7 4_RxD- - 26 4_GND 4_GND
8 4_RTS- - 27 4_CTS+ -
9 4_RTS+ - 28 4_TxD+ 4_Data+
10 4_RxD+ -
29 2_CTS- -
11 2_TxD- 2_Data- 30 2_RxD- -
12 2_GND 2_GND 31 2_RTS- -
13 2_CTS+ 32 2_RTS+ -
14 2_TxD+ 2_Data+ 33 2_RxD+ -
15 1_CTS- - 34 1_TxD- 1_Data-
16 1_RxD- - 35 1_GND 1_GND
17 1_RTS- - 36 1_CTS+ -
18 1_RTS+ - 37 1_TxD+ 1_Data+
19 1_RxD+ -