User manual
Table Of Contents
- Chapter 1 Introduction
- Chapter 2 Hardware Configuration
- 2.1 Initial Inspection
- 2.2 Jumper and Switch Locations
- Figure 2.1: PCI-1601A/B Silk Screen
- Figure 2.2: PCI-1601AU/BU Silk Screen
- Figure 2.3: PCI-1602A/B Silk Screen
- Figure 2.4: PCI-1602AU/BU Silk Screen
- Figure 2.5: PCI-1602UP Silk Screen
- Figure 2.6: PCI-1603 Silk Screen
- Figure 2.7: PCI-1604UP Silk Screen
- Figure 2.8: PCI-1610A/B Silk Screen
- Figure 2.9: PCI-1610CU Silk Screen
- Figure 2.10: PCI-1610AUP/UP Silk Screen
- Figure 2.11: PCI-1610AJP Silk Screen
- Figure 2.12: PCI-1611U Silk Screen
- Figure 2.13: PCI-1612A/B Silk Screen
- Figure 2.14: PCI-1612AU/U Silk Screen
- Figure 2.15: PCI-1612CU Silk Screen
- Figure 2.16: PCI-1620A/B Silk Screen
- Figure 2.17: PCI-1620AU/U Silk Screen
- Figure 2.18: PCI-1622CU Silk Screen
- 2.3 Jumper Settings
- 2.3.1 How to Set Jumpers
- 2.3.2 Default Settings
- 2.3.3 Mode Selection by Jumper/DIP Settings
- Figure 2.21: PCI-1612 Series RS-232/422/485 Selection
- Figure 2.22: RS-422/485 Selection by Jumper Setting
- Figure 2.23: PCI-1603 RS-232 Mode Jumper Setting
- Figure 2.24: PCI-1603 Current-loop Mode Jumper Setting
- Figure 2.25: Active Mode Jumper Setting
- Figure 2.26: Passive Mode Jumper Setting
- Figure 2.27: Resistor Selection
- 2.4 Card Installation
- Chapter 3 Driver Setup & Installation
- Chapter 4 ICOM Tools
- Chapter 5 Pin Assignments and Wiring
PCI-COMMUNICATION User Manual viii
2.4 Card Installation .............................................................. 35
Chapter 3 Driver Setup & Installation.......................... 38
3.1 Introduction ..................................................................... 38
3.2 Driver Setup .................................................................... 38
3.2.1 Steps for Windows 98/2000/XP Driver Setup ............. 38
3.3 Reboot System after Win98/2000/XP Driver Setup ....... 44
3.3.1 PCI UARTs Device Driver Installation ....................... 44
3.3.2 PCI Bridge Device Driver Installation ......................... 46
3.4 Verify your Win98/2000/XP Driver Setup ..................... 47
3.5 Configuring Serial Devices for Win 98/2000/XP ........... 50
3.5.1 Configuring a PCI UARTs Device .............................. 52
3.5.2 Configuring a PCI Bridge Device ................................ 53
3.5.3 Configuring Ports ......................................................... 53
3.6 Remove PCI ICOM Series Device.................................. 54
3.7 Driver Uninstall............................................................... 57
Chapter 4 ICOM Tools ................................................... 60
4.1 Introduction .................................................................... 60
4.2 Installation....................................................................... 60
4.3 User Interface of ICOM Tools ........................................ 61
4.3.1 Menu Bar ..................................................................... 61
4.3.2 Tool Bar ....................................................................... 62
4.3.3 Com Port Tab ............................................................... 63
4.3.4 Port Status .................................................................... 64
4.3.5 Message Logo .............................................................. 64
4.3.6 Tx Slide Bar ................................................................. 65
4.3.7 Performance Listing Area ............................................ 65
4.3.8 Status Bar ..................................................................... 65
4.4 Using the ICOM Tools Utility ........................................ 66
4.4.1 Port Selection ............................................................... 66
Figure 4.1:ICOM Tools program window ................... 66
Figure 4.2:Select Port dialog box ................................ 67
Figure 4.3:Ports You Select Will Appear in the Selected
Port Checkbox Group ...................................... 67
Figure 4.4:ICOM Tools User Interface ........................ 68
4.4.2 Configuring a Port ....................................................... 68
Figure 4.5:Test Info. on Performance Listing Area ..... 69
4.4.3 Close Port ..................................................................... 70
4.4.4 Exit the ICOM Tools utility ......................................... 70
4.5 Messages on Status Bar and Message Logo Area........... 71
4.5.1 Status Bar Messages .................................................... 71
4.5.2 Message Logo Messages ............................................. 72
Chapter 5 Pin Assignments and Wiring........................ 74
5.1 Pin assignments............................................................... 74
5.1.1 PCI-1601A/AU/B/BU, PCI-1602A/AU/B/BU ............ 74
Table 5.1:PCI-1601/1602 Male DB9 on bracket ......... 74
Figure 5.1:PCI-1601/1602 Pin Assignment ................. 74