User manual
Table Of Contents
- PCA-6011
- Contents
- 1 Hardware Configuration
- 1.1 Introduction
- 1.2 Features
- 1.3 Specifications
- 1.4 Jumpers and Connectors
- 1.5 Board Layout: Jumper and Connector Locations
- 1.6 PCA-6011 Block Diagram
- 1.7 Safety Precautions
- 1.8 Jumper Settings
- 1.9 System Memory
- 1.10 Memory Installation Procedures
- 1.11 Cache Memory
- 1.12 Processor Installation
- 1.13 Power Model Setting and Installation
- 1.14 ATX Mode
- 2 Connecting Peripherals
- 2.1 Introduction
- 2.2 IDE Connectors (IDE1)
- 2.3 Floppy Drive Connector (FDD1)
- 2.4 Parallel Port (LPT1)
- 2.5 VGA Connector (VGA1)
- 2.6 Serial Ports (COM1, COM2)
- 2.7 PS/2 Keyboard and Mouse Connector (KBMS1)
- 2.8 External Keyboard & Mouse (KBMS2)
- 2.9 CPU Fan Connector (CPUFAN1)
- 2.10 Front Panel Connectors (JFP1, JFP2, JFP3)
- 2.11 H/W Monitor Alarm (JOBS1)
- 2.12 LAN RJ45 connector (LAN1/LAN2)
- 2.13 HD Link connector (HDAUD1)
- 2.14 Serial ATA2 Interface (SATA1 ~ SATA4)
- 2.15 LAN LED connector (LAN LED1)
- 2.16 USB (USB12, USB34, USB56, USB78)
- 2.17 Case open (JCASE1)
- 3 AMI BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.2.1 Main Setup
- 3.2.2 Advanced BIOS Features Setup
- 3.2.3 PCI/PNP Setup
- 3.2.4 Boot Settings
- 3.2.5 Security Settings
- 3.2.6 Advanced Chipset Settings
- 3.2.7 Exit Options
- 4 Chipset Software Installation Utility
- 5 VGA Setup
- 6 LAN Configuration
- A Programming the Watchdog Timer
- B I/O Pin Assignments
- B.1 IDE Hard Drive Connector (IDE1)
- B.2 Floppy Drive Connector (FDD1)
- B.3 Parallel Port Connector (LPT1)
- B.4 VGA Connector (VGA1)
- B.5 RS-232 Serial Port (COM1, COM2)
- B.6 PS/2 Keyboard/Mouse Connector (KBMS1)
- B.7 External Keyboard Connector (KBMS2)
- B.8 CPU Fan Power Connector (CPUFAN1)
- B.9 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK)
- B.10 External Speaker Connector (JFP2 / SPEAKER)
- B.11 Reset Connector (JFP1 / RESET)
- B.12 HDD LED (JFP2 / HDDLED)
- B.13 ATX Soft Power Switch (JFP1 / PWR_SW)
- B.14 SM Bus Connector (JFP2/SNMP)
- B.15 HD Link connector (HDAUD1)
- B.16 LAN LED Connector (LAN LED1)
- B.17 AT Power Connector (ATXF1)
- B.18 H/W Monitor Alarm (JOBS1)
- B.19 USB Connector (USB12, USB34, USB56, USB78)
- B.20 Case Open Connector (JCASE1)
- B.21 GPIO Pin Header (GPIO1)
- B.22 System I/O Ports
- B.23 DMA Channel Assignments
- B.24 Interrupt Assignments
- B.25 1st MB Memory Map
- B.26 PCI Bus Map
85 PCA-6011 User Manual
A
ppendix B I/O Pin
A
ssignments
B.23 DMA Channel Assignments
B.24 Interrupt Assignments
C90-C97 COM5
C98-C9F COM6
4D0-4D1 Interrupt Controller
CF9 Reset Generator
Table B.22: System I/O Ports
Table B.23: DMA Channel Assignments
Channel Signal
0 Available
1 Available
2 Floppy disk (8-bit transfer)
3 Available
4 Cascade for DMA controller 1
5 Available
6 Available
7 Available
Table B.24: Interrupt Assignments
Priority Interrupt# Interrupt Source
1 NMI Parity error detected
2IRQ0Interval timer
3 IRQ1 Keyboard
- IRQ2 Interrupt from controller 2 (cascade)
4IRQ8Real-time clock
5 IRQ9 Cascaded to INT 0A (IRQ 2)
6 IRQ10 Available
7 IRQ11 Available
8IRQ12PS/2 mouse
9 IRQ13 INT from co-processor
10 IRQ14 IDE Channel
12 IRQ3 Serial communication port 2
13 IRQ4 Serial communication port 1
14 IRQ5 Parallel port 2
15 IRQ6 Diskette controller (FDC)
16 IRQ7 Parallel port 1 (print port)