User manual
Table Of Contents
- PCA-6011
- Contents
- 1 Hardware Configuration
- 1.1 Introduction
- 1.2 Features
- 1.3 Specifications
- 1.4 Jumpers and Connectors
- 1.5 Board Layout: Jumper and Connector Locations
- 1.6 PCA-6011 Block Diagram
- 1.7 Safety Precautions
- 1.8 Jumper Settings
- 1.9 System Memory
- 1.10 Memory Installation Procedures
- 1.11 Cache Memory
- 1.12 Processor Installation
- 1.13 Power Model Setting and Installation
- 1.14 ATX Mode
- 2 Connecting Peripherals
- 2.1 Introduction
- 2.2 IDE Connectors (IDE1)
- 2.3 Floppy Drive Connector (FDD1)
- 2.4 Parallel Port (LPT1)
- 2.5 VGA Connector (VGA1)
- 2.6 Serial Ports (COM1, COM2)
- 2.7 PS/2 Keyboard and Mouse Connector (KBMS1)
- 2.8 External Keyboard & Mouse (KBMS2)
- 2.9 CPU Fan Connector (CPUFAN1)
- 2.10 Front Panel Connectors (JFP1, JFP2, JFP3)
- 2.11 H/W Monitor Alarm (JOBS1)
- 2.12 LAN RJ45 connector (LAN1/LAN2)
- 2.13 HD Link connector (HDAUD1)
- 2.14 Serial ATA2 Interface (SATA1 ~ SATA4)
- 2.15 LAN LED connector (LAN LED1)
- 2.16 USB (USB12, USB34, USB56, USB78)
- 2.17 Case open (JCASE1)
- 3 AMI BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.2.1 Main Setup
- 3.2.2 Advanced BIOS Features Setup
- 3.2.3 PCI/PNP Setup
- 3.2.4 Boot Settings
- 3.2.5 Security Settings
- 3.2.6 Advanced Chipset Settings
- 3.2.7 Exit Options
- 4 Chipset Software Installation Utility
- 5 VGA Setup
- 6 LAN Configuration
- A Programming the Watchdog Timer
- B I/O Pin Assignments
- B.1 IDE Hard Drive Connector (IDE1)
- B.2 Floppy Drive Connector (FDD1)
- B.3 Parallel Port Connector (LPT1)
- B.4 VGA Connector (VGA1)
- B.5 RS-232 Serial Port (COM1, COM2)
- B.6 PS/2 Keyboard/Mouse Connector (KBMS1)
- B.7 External Keyboard Connector (KBMS2)
- B.8 CPU Fan Power Connector (CPUFAN1)
- B.9 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK)
- B.10 External Speaker Connector (JFP2 / SPEAKER)
- B.11 Reset Connector (JFP1 / RESET)
- B.12 HDD LED (JFP2 / HDDLED)
- B.13 ATX Soft Power Switch (JFP1 / PWR_SW)
- B.14 SM Bus Connector (JFP2/SNMP)
- B.15 HD Link connector (HDAUD1)
- B.16 LAN LED Connector (LAN LED1)
- B.17 AT Power Connector (ATXF1)
- B.18 H/W Monitor Alarm (JOBS1)
- B.19 USB Connector (USB12, USB34, USB56, USB78)
- B.20 Case Open Connector (JCASE1)
- B.21 GPIO Pin Header (GPIO1)
- B.22 System I/O Ports
- B.23 DMA Channel Assignments
- B.24 Interrupt Assignments
- B.25 1st MB Memory Map
- B.26 PCI Bus Map
29 PCA-6011 User Manual
Chapter 3
A
MI BIOS Setup
3.2 Entering Setup
Press the "Del" key during the Power On Self Test (POST) process to enter the BIOS
setup screen, otherwise the system will continue the POST process.
3.2.1 Main Setup
When you first enter the BIOS Setup Utility, you will enter the Main setup screen. You
can always return to the Main setup screen by selecting the Main tab. There are two
Main Setup options. They are described in this section. The Main BIOS Setup screen
is shown below.
Figure 3.2 Main Setup Screen
The Main BIOS setup screen has two main frames. The left frame displays all the
options that can be configured. Grayed-out options cannot be configured; options in
blue can. The right frame displays the key legend.
Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will accom-
pany it.
3.2.1.1 System time / System date
Use this option to change the system time and date. Highlight System Time or Sys-
tem Date using the <Arrow> keys. Enter new values through the keyboard. Press the
<Tab> key or the <Arrow> keys to move between fields. The date must be entered in
MM/DD/YY format. The time must be entered in HH:MM:SS format.