User Manual PCA-6011 PICMG 1.
Copyright The documentation and the software included with this product are copyright 2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
A Message to the Customer Advantech Customer Services Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known. Your satisfaction is our primary concern.
Memory Compatibility Brand Size Speed Type Memory Advantech PN 1GB 1066 DDR3 SEC K4B1G0846D-HCF8 (128x8) 96D3-1G1066NNTR Transcend 1GB 1066 DDR3 SEC K4B1G0846D HCH9 ENJ038A3 (128x8) 96D3-1G1066NNTR 2GB 1066 DDR3 SEC K4B1G0846D-HCF9(128x8) 96D3-2G1066NNTR 1GB 1066 DDR3 ELPIDA J1108BABG-AE-E (128x8) 96D3-1G1066NNAP 1GB 1066 DDR3 ELPIDA J1108BABG-DJ-E (128x8) 96D3-1G1066NNAP 2GB 1066 DDR3 ELPIDA J1108BABG-AE-E (128x8) 96D3-2G1066NNAP 2GB 1066 DDR3 ELPIDA J1108BABG-DJ-E 092109D
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Initial Inspection Before you begin installing your single board computer, please make sure that the following materials have been shipped: PCA-6011 Intel® LGA775 processor-based single board computer 1 PCA-6011 startup manual 1 CD with driver utility and manual (in PDF format) 1 Ultra ATA 66/100 IDE cable 2 Serial ATA HDD data cable 2 Serial ATA HDD power cable 1 Printer (parallel) port & COM port cable kit 1 Y cable for PS/2 keyboard and PS/2 mouse 1 USB cable with 4 ports 1 Jum
Contents Chapter 1 Hardware Configuration......................1 1.1 1.2 1.3 1.14 Introduction ............................................................................................... 2 Features .................................................................................................... 2 Specifications ............................................................................................ 3 1.3.1 System ...............................................................................
2.11 2.16 2.17 H/W Monitor Alarm (JOBS1)................................................................... 22 Table 2.2: Hardware Monitor Alarm setting............................... 22 LAN RJ45 connector (LAN1/LAN2) ........................................................ 22 HD Link connector (HDAUD1) ................................................................ 23 Serial ATA2 Interface (SATA1 ~ SATA4)................................................ 23 LAN LED connector (LAN LED1)....................
6.2 6.3 6.4 Features .................................................................................................. 60 Installation ............................................................................................... 60 Win XP Driver Setup ............................................................................... 61 Appendix A Programming the Watchdog Timer..65 A.1 Programming the Watchdog Timer ......................................................... 66 A.1.
B.22 B.23 B.24 B.25 B.26 PCA-6011 User Manual System I/O Ports..................................................................................... 84 Table B.22:System I/O Ports ...................................................... 84 DMA Channel Assignments .................................................................... 85 Table B.23:DMA Channel Assignments ..................................... 85 Interrupt Assignments .............................................................................
Chapter 1 Hardware Configuration 1
1.1 Introduction The PCA-6011 is designed with the Intel® G41 + ICH7/ICH7R (only for G2 SKU) to support Core™ 2 Quad / Core™ 2 Duo /channel 440 processors (refer to “Processor Support” on page v) with a 800/1066/1333 MHz front side bus and dual channel DDR3 800/1066 MHz memory up to 4 GB. It follows the PICMG 1.0 specification and is the best solution for high-performance computing and applications that demand a wide I/O bandwidth.
1.3.1 System CPU: Intel® LGA 775 CoreTM 2 Quad, CoreTM 2 Duo, Celeron® 440 up to 2.66/ 3.33/2.2 GHz, (refer to “Processor Support” on page iv), FSB 800/1066/1333 MHz. PCA-6011 also has an optional CPU cooler (1750000332) for customers who use high-speed CPUs in 2U chassis or in a high-temperature environment.
1.3.6 Mechanical and environmental specifications Operating temperature: 0 ~ 60° C (32 ~ 140° F, depending on CPU) (operating humidity: 40° C @ 85% RH Non-Condensing) Storage temperature: -40 ~ 85° C (-40 ~ 185° F) non-condensing and 60° C @ 95% RH non-condensing Power supply voltage: +5 V, +12 V, +5 VSBY Power consumption: – Configuration1: +5 V at 4.04 A, +12 V at 5.14 A, +5 VSBY at 0.17 A (Intel Core 2 Quad processor Q9400 2.
Chapter 1 Table 1.
1.5 Board Layout: Jumper and Connector Locations Figure 1.
Chapter 1 1.6 PCA-6011 Block Diagram DVI Display port IDE DMA 33/66/100 4 SATA II Ports 300 MHz Channel A DDR3 800/1066 Channel B DDR3 800/1066 G41 GMCH DMI CRT Hardware Configuration VGA MHz FSB 1066 / 1333 Intel LGA775 C2Q/C2D USB 2.0/1.1 HD Audio (Optional) HD Audio G-LAN1 Intel 82583V PCIe x1 G-LAN2 Intel 82583V PCI Bus PCI to ISA Bridge ITE8888 PCI Bus Backplane (PICMG 1.
1.7 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the boards. Modern electronic devices are very sensitive to static electric charges.
Chapter 1 . Table 1.3: CMOS (CMOS1) Function Jumper Setting * Keep CMOS data 1-2 closed Clear CMOS data 2-3 closed 1.8.3 Watchdog timer output (JWDT1) The PCA-6011 contains a watchdog timer that will reset the CPU in the event the CPU stops processing. This feature means the PCA-6011 will recover from a software failure or an EMI problem. The JWDT1 jumper settings control the outcome of what the computer will do in the event the watchdog timer is tripped. Table 1.
1.11 Cache Memory The CPU that PCA-6011 supports built-in 6 MB (for Core 2 Quad), 6 MB (for Core 2 Duo), 512 KB (for Celeron 440) full-speed L2 cache. The built-in second-level cache in the processor yields much higher performance than conventional external cache memories. 1.12 Processor Installation The PCA-6011 is designed for Intel® LGA 775 socket CPUs. 1. Pull the bar beside the CPU socket outward and lift it. 2. Align the triangular marking on the processor with the cut edge of the socket.
Put back the socket cap and press down the bar to fix it. Chapter 1 3. PCA-6011 can support AT or ATX power model settings. 1.13.1 AT Mode 1. Short ATXF1 2-3 pins on CPU board. 2. Short PSON1(CN1) 1-2 pins on Backplane. 11 PCA-6011 User Manual Hardware Configuration 1.
3. Connect the power supply and the ATX12V1 connector on the CPU board. 4. Connect the power supply and the EATXPWR1 (VATX1) connector on the CPU board.
1. Use 3 pin ATX signal cable (P/N:1700030500) connect the ATXF1 on the CPU board with PSON (CN1) on the backplane. Chapter 1 1.
2. Connect the power supply and the ATX12V1 connector on the CPU board. 3. Connect the power supply and the EATXPWR1 (VATX1) connector on the CPU board.
Chapter 2 Connecting Peripherals 2
2.1 Introduction You can access most of the connectors from the top of the board while it is installed in the chassis. If you have a number of cards installed or have a packed chassis, you may need to partially remove the card to make all the connections. 2.2 IDE Connectors (IDE1) You can attach up to two IDE (Integrated Drive Electronics) drives to the PCA-6011's built-in controller. Wire number 1 on the cable is red or blue and the other wires are gray.
Chapter 2 2.3 Floppy Drive Connector (FDD1) 2.4 Parallel Port (LPT1) The parallel port is normally used to connect the single board computer to a printer. The PCA-6011 includes an onboard parallel port, accessed through a 26-pin flatcable connector, LPT1. The card comes with an adapter cable which lets you use a traditional DB-25 connector. The cable has a 26-pin connector on one end and a DB25 connector on the other, mounted on a retaining bracket.
To install the bracket, find an empty slot in your chassis. Unscrew the plate that covers the end of the slot. Screw in the bracket in place of the plate. Next, attach the flatcable connector to LPT1 on the CPU card. Wire 1 of the cable is red or blue, and the other wires are gray. Make sure that wire 1 corresponds to pin 1 of LPT1. Pin 1 is on the upper right side of LPT1. 2.5 VGA Connector (VGA1) The PCA-6011 includes a VGA interface that can drive conventional CRT displays.
2.8 External Keyboard & Mouse (KBMS2) In addition to the PS/2 mouse/keyboard connector on the PCA-6011's rear plate, there is also an extra onboard external keyboard and mouse connector. This gives system integrators greater flexibility in designing their systems. 19 PCA-6011 User Manual Connecting Peripherals One 6-pin mini-DIN connectors (KBMS1) on the card mounting bracket provide connection to a PS/2 keyboard or a PS/2 mouse, respectively.
2.9 CPU Fan Connector (CPUFAN1) If a fan is used, this connector supports cooling fans of 12 V/1 A (12 W) or less. 2.10 Front Panel Connectors (JFP1, JFP2, JFP3) There are several external switches to monitor and control the PCA-6011. 2.10.1 ATX soft power switch (JFP1 / PWR_SW) If your computer case is equipped with an ATX power supply, you should connect the power on/off button on your computer case to (JFP1 / PWR_SW). This connection enables you to turn your computer on and off.
Many computer cases offer the convenience of a reset button. Connect the wire for the reset button. 2.10.3 HDD LED (JFP2 / HDDLED) You can connect an LED to connector (JFP2 / HDDLED) to indicate when the HDD is active. This connector is reserved for Advantech’s SNMP-1000 HTTP/SNMP Remote System Manager. The SNMP-1000 allows users to monitor the internal voltages, temperature and fans from a remote computer through an Ethernet network. (JFP2 / SNMP) can be connected to CN19 of SNMP-1000.
2.11 H/W Monitor Alarm (JOBS1) (JOBS1) is a 2-pin jumper to enable/disable the alarm for on board security events. Table 2.2: Hardware Monitor Alarm setting Pin setting Function closed Enable OBS alarm open Disable OBS alarm 2.12 LAN RJ45 connector (LAN1/LAN2) PCA-6011 uses the Intel 82583V Gigabit LAN chip which is linked to PCIe x1 link (LAN2 only exists on PCA-6011G2). With this chip, PCA-6011 may provide high throughputs for a heavy load networking environment.
Chapter 2 2.13 HD Link connector (HDAUD1) 2.14 Serial ATA2 Interface (SATA1 ~ SATA4) In addition to the EIDE interfaces (up to two devices), the PCA-6011 features a high performance serial ATA2 interface (up to 300MB/s) which eases cabling to hard drives with thin and long cables. 23 PCA-6011 User Manual Connecting Peripherals The PCA-6011 provides HD audio through PCA-AUDIO-HDA1E module from Advantech.
2.15 LAN LED connector (LAN LED1) PCA-6011 provides an external LAN LED Pin header for connecting to the front side of the chassis. With this convenient design users can easily see whether the LAN port is active or not. Refer to Appendix B for detailed information on the pin assignments. Table 2.
2.17 Case open (JCASE1) PCA-6011 provides 2-Pins pin header for case open detection. This function could be enabled or disabled in the BIOS setting. When the PIN is shorted, it will cause the on board buzzer to sound. 25 PCA-6011 User Manual Connecting Peripherals The PCA-6011 provides eight on board USB 2.0 ports which support transmission rates up to 480 Mbps and which are fuse-protected.
PCA-6011 User Manual 26
Chapter 3 AMI BIOS Setup 3
3.1 Introduction With the AMI BIOS Setup program, you can modify BIOS settings and control the features of your computer. The Setup program uses a number of menus for reflecting the current system status and controlling the system. This chapter describes the basic navigation of the PCA-6011 setup screens. Figure 3.1 Setup Program Initial Screen AMI's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration.
Press the "Del" key during the Power On Self Test (POST) process to enter the BIOS setup screen, otherwise the system will continue the POST process. 3.2.1 Main Setup Figure 3.2 Main Setup Screen The Main BIOS setup screen has two main frames. The left frame displays all the options that can be configured. Grayed-out options cannot be configured; options in blue can. The right frame displays the key legend. Above the key legend is an area reserved for a text message.
3.2.2 Advanced BIOS Features Setup Select the Advanced tab from the PCA-6011 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screen is shown below. The sub menus are described on the following pages.
3.2.2.2 IDE Configuration Figure 3.5 IDE Configuration ATA/IDE Configuration This can be configured as Disabled, or Enhanced. If enhanced mode is turned on, primary, secondary and third IDE can be configured. Hard Disk Write Protect 31 PCA-6011 User Manual AMI BIOS Setup Chapter 3 You may choose to enable or disable it.
This will be effective only if device is accessed through BIOS. You may choose to enable or disable it IDE Detect Time Out (sec) Select the time out value for detecting IDE devices. ATA (PI) 80Pin Cable Detection This item is for ATA 80 pin cable detection. 3.2.2.3 Super I/O Configuration Figure 3.6 Super I/O Configuration OnBoard Floppy Controller Enable or disable the floppy function. Floppy A Select the type of floppy drive connected to the system.
Chapter 3 This option configures s Parallel Port base IRQ. 3.2.2.4 Hardware Health Function CPUFAN Mode Setting Use this to set the SmartFan control function or disabled SmartFan. Chassis Intrusion Enable/Disable the Chassis Intrusion monitoring function. When the case is opened, the buzzer beeps. CPU Warning Temperature Use this to set the CPU warning temperature threshold. When the system reaches the warning temperature, the buzzer will beep.
3.2.2.5 APM Configuration Figure 3.8 APM Configuration Power Management/APM Enable or disable APM power management function. Power Button Mode Power on, off or enter suspend mode when the power button is pressed. The following options are also available. Resume On Ring: Disable/Enable RI wake event. Resume On LAN: Disable/Enable LAN PME wake event. Resume On RTC Alarm: Disable/Enable RTC wake event Throttle Slow Clock Ratio Select the duty cycle in throttle mode.
Chapter 3 3.2.2.6 MPS Configuration AMI BIOS Setup Figure 3.9 MPS Configuration MPS revision This item will allow you choose the version of MPS table to fit your OS system. 3.2.2.7 Smbios Configuration Figure 3.10 Smbios Configuration Smbios SMI support Enable or disable the SMI wrapper support.
3.2.2.8 USB configuration Legacy USB Support This is for supporting USB device under legacy OS such as DOS. When choosing "AUTO", the system will automatically detect if any USB device is plugged into the computer and enable USB legacy mode when a USB device is plugged and disable USB legacy mode when no USB device is plugged. USB 2.0 Controller Mode This is to set speed of the USB 2.0 Controller. BIOS EHCI Hand-off This enables or disables supporting OS without EHCI hand-off feature.
Select the PCI/PnP tab from the PCA-6011 setup screen to enter the Plug and Play BIOS Setup screen. Highlighting a Plug and Play BIOS Setup option by using the keys displays a description in the right hand panel. All Plug and Play BIOS Setup options are described in this section. The Plug and Play BIOS Setup screen is shown below. Chapter 3 3.2.3 PCI/PNP Setup AMI BIOS Setup Figure 3.11 PCI/PNP Setup_1 Figure 3.12 PCI/PNP Setup_2 3.2.3.
3.2.3.2 Plug and Play O/S Set this value to allow the system to modify the settings for Plug and Play operating system support. The Optimal and Fail-Safe default setting is No. 3.2.3.3 PCI Latency Timer Use this to adjust the PCI Latency Timer. This option sets the latency of all PCI devices on the PCI bus. The Optimal and Fail-Safe default setting is 64. 3.2.3.4 Allocate IRQ to PCI VGA Set this value to allow or stop the system from giving the VGA adapter card an interrupt address.
Chapter 3 3.2.4 Boot Settings AMI BIOS Setup Figure 3.13 Boot Settings Figure 3.14 Boot Settings Configuration The following options are available: Quick Boot Allows the BIOS to skip certain tests while booting. This will decrease the time needed to boot the system. Quiet Boot If this option is set to Disabled, the BIOS displays normal POST messages. If Enabled, an OEM Logo is shown instead of POST messages.
Bootup Num-Lock Select the Power-on state for Numlock. PS/2 Mouse Support Enable or disable PS/2 interface mouse support. Available options include Auto, Enable, Disable. Wait For 'F1' If Error Wait for the F1 key to be pressed if an error occurs. Hit 'DEL' Message Display Displays "Press DEL to run Setup" in POST. Interrupt 19 Capture Enable or disable option ROM to trap interrupt 19. 3.2.5 Security Settings Figure 3.
Chapter 3 3.2.6 Advanced Chipset Settings 3.2.6.1 North Bridge Configuration Allows user to set graphic and memory controller configurations. Figure 3.17 North Bridge Configuration Memory remap feature The feature allows you to enable or disable the remapping of the overlapped PCI memory above the total physical memory. DRAM Frequency Allows user to set DDR2 memory operating frequency. Configure DRAM Timing by SPD Allows user to set DRAM operating timing coefficients by SPD or Manual.
15-16 MB of memory block reserved for legacy ISA devices. You may choose disable and 15-16 MB. Initiate Graphic Adapter Allows user to set initial video output device. Available options include IGD, PCI/ IGD. Internal Graphics Mode Select Allows user to set graphic mode for DOS environment. Available options include Disable, Enable 32 MB, Enable 64 MB, Enable 128 MB. Video Function Configuration This allows user to set IGD (Integrated Graphics Device) configuration. Figure 3.
Chapter 3 3.2.6.2 South Bridge Chipset Configuration Allows user to set I/O port configurations. USB Functions Select: Disabled, 2 USB Ports, 4 USB Ports, 6 USB Ports or 8 USB Ports. USB 2.0 Controller Enables or disables the USB 2.0 controller. Audio controller Allows user to choose Auto or Azalia to manage the audio controller. SMBUS Controller Enables or disables the SMBUS controller. Reserved Page Route Allows user to set Port 80 information output port.
3.2.7 Exit Options Figure 3.20 Exit Options 3.2.7.1 Save Changes and Exit When you have completed system configuration, select this option to save your changes, exit BIOS setup and reboot the computer so the new system configuration parameters can take effect. 1. Select Save Changes and Exit from the Exit menu and press . The following message appears: Save Configuration Changes and Exit Now? [Ok] [Cancel] 2. Select “Ok” or “Cancel”. 3.2.7.
PCA-6011 User Manual AMI BIOS Setup 45 Chapter 3 3.2.7.5 Load Failsafe Defaults The PCA-6011 automatically configures all setup options to failsafe settings when you select this option. Failsafe Defaults are designed for maximum system stability, but not maximum performance. Select Failsafe Defaults if your computer is experiencing system configuration problems. 1. Select Load Failsafe Defaults from the Exit menu and press . The following message appears: Load Failsafe Defaults? [OK] [Cancel] 2.
PCA-6011 User Manual 46
Chapter 4 Chipset Software Installation Utility 4
4.1 Before You Begin To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the PCA-6011 are located on the software installation CD. Updates are provided via Service Packs from Microsoft*. Note! The files on the software installation CD are compressed. Do not attempt to install the drivers by copying the files manually. You must use the supplied SETUP program to install the drivers.
1. Insert the driver CD into your system’s CD-ROM drive. Select the folder "Driver" then select folder "01_Chipset" and click "infinst_autol.exe". A message pops up telling you to install the CSI utility before other device drivers. Windows XP is used as an example in the following steps. Chapter 4 4.
2. Click “Next” when you see the following message. 3. Click “Yes” when you see the following message.
5. Click "Next" when you see the following message. 51 Chipset Software Installation Utility Click “Next” when you see the following message. Chapter 4 4.
6. When the following message appears, click “Finish” to complete the installation and restart Windows.
Chapter 5 VGA Setup 5
5.1 Introduction The Intel G41 integrated graphics controller provides an analog display port. You need to install the VGA driver to enable the function. The Intel G41 integrated graphics controller incorporates the latest Microsoft* DirectX*9 support capabilities. It allows software developers to create life like environments and characters.
4. Click "Exit" to complete the installation and restart the computer. VGA Setup You will see a welcome window. Please read the license terms and select the item, then click "Install" to start the installation. Chapter 5 3.
5.3 Windows XP Driver Setup Note! Before installing this driver, make sure the CSI utility and .NET Framework has been installed in your system. See Chapter 4 and Section 5.2 for information on installing the CSI utility and .NET Framework. 1. Insert the driver CD into your system's CD-ROM drive. Select the folder "02_Graphic" then click the proper VGA driver for the OS. Windows XP is used as an example in the following steps. 2. You will see a welcome window.
Click "Yes" when you see the following message. 4. When you see the following message, please click "Next" to continue the installation. Chapter 5 3.
5. Please click "Next" to continue the installation. 6. Click “Finish” to complete the installation and restart the computer now or later.
Chapter 6 6 LAN Configuration
6.1 Introduction The PCA-6011 has a single Gigabit Ethernet LAN via dedicated PCI Express x 1 bus (Intel® 82583V), which offers bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet to operate at 1000 Mbps. 6.2 Features Integrated 10/100/1000 Mbps transceiver 10/100/1000 Mbps triple-speed MAC High-speed RISC core with 24-KB cache On-chip voltage regulation Wake-on-LAN (WOL) support PCI Express X1 host interface 6.
Insert the driver CD into your system's CD-ROM drive. Select the folder "04_LAN" then click "Autorun.exe" for the driver install. Windows XP is used as an example in the following steps. 2. Select "Install Drivers and Software" to install driver. LAN Configuration 1. Chapter 6 6.
3. You will see a welcome window. Please click "Next" to continue the installation. 4. Select “I accept the terms in the license agreement” and click “Next” to continue.
Click “Next” to continue. 6. Click “Install” to start the installation procedure. Chapter 6 5.
7. Click "Finish" to complete the installation and the LAN function will be enabled after the installation.
Appendix A A Programming the Watchdog Timer
A.1 Programming the Watchdog Timer The PCA-6011 watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to program it. A.1.1 Watchdog timer overview The watchdog timer is built in to the super I/O controller W83627DHG-P. It provides the following functions for user programming: Can be enabled and disabled by user's program.
Appendix A Programming the Watchdog Timer Unlock W83627DHG-P Select Register of Watchdog Timer Enable Watchdog Timer Function Use the Watchdog Timer Function Lock 83627DHG-P 67 PCA-6011 User Manual
Table A.1: Watchdog Timer Registers Address of Register (2E) Attribute Value (2F) & Description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock the W83627DHG-P 07 (hex) write Write 08 (hex) to select register of watchdog timer. 30 (hex) write Write 01 (hex) to enable the function of the watchdog timer. Disabled is set as default. write Set seconds or minutes as units for the timer. Write 0 to bit 3: set second as counting unit.
1. Enable watchdog timer and set 10 sec.
;----------------------------------------------------------Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------Dec dx ; Set minute as counting unit Mov al,0f5h Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;---------------------------------------------------------
71 PCA-6011 User Manual Appendix A Programming the Watchdog Timer Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------Dec dx ; Enable watchdog timer to be reset by mouse Mov al,0f7h Out dx,al Inc dx In al,dx Or al,80h Out dx,al ;----------------------------------------------------------Dec dx ; lock W83627DHG-P Mov al,0aah Out dx,al 4.
;----------------------------------------------------------Dec dx ; lock W83627DHG-P Mov al,0aah Out dx,al 5.
Appendix B B I/O Pin Assignments
B.1 IDE Hard Drive Connector (IDE1) Table B.
33 31 3 1 34 32 4 2 Table B.
B.3 Parallel Port Connector (LPT1) 13 12 2 1 26 25 15 14 Table B.
5 Appendix B I/O Pin Assignments B.4 VGA Connector (VGA1) 1 10 6 15 11 Table B.4: VGA Connector (VGA1) Pin Signal Pin Signal 1 RED 2 GREEN 3 BLUE 4 N/C 5 GND 6 VGA_En 7 GND 8 GND 9 VCC 10 GND 11 N/C 12 SDT 13 H-SYNC 14 V-SYNC 15 SCK B.5 RS-232 Serial Port (COM1, COM2) 9 7 5 3 1 8 6 4 2 Table B.
B.6 PS/2 Keyboard/Mouse Connector (KBMS1) 6 5 4 3 2 1 Table B.6: PS/2 Keyboard/Mouse Connector (KBMS1) Pin Signal 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB CLOCK 6 MS CLOCK B.7 External Keyboard Connector (KBMS2) 6 5 4 3 2 1 Table B.
1 2 3 4 Table B.8: CPU Fan Power Connector (CPUFAN1) Pin Signal 1 GND 2 +12 V 3 Detect 4 FANPWM B.9 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK) Table B.9: Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK) Pin Signal 1 Power LED(+5 V) 2 NC 3 GND 4 KEYLOCK# 5 GND 79 PCA-6011 User Manual Appendix B I/O Pin Assignments B.
B.10 External Speaker Connector (JFP2 / SPEAKER) Table B.10: External Speaker Connector (JFP2 / SPEAKER) Pin Signal 1 SPK+ 2 NC 3 SPK_IN 4 SPK- B.11 Reset Connector (JFP1 / RESET) Table B.11: Reset Connector (JFP1 / RESET) Pin Signal 1 RESET # 2 GND B.12 HDD LED (JFP2 / HDDLED) Table B.
Table B.13: ATX Soft Power Switch (JFP1 / PWR_SW) Pin Signal 1 5VSB 2 PWR-BTN B.14 SM Bus Connector (JFP2/SNMP) Table B.14: SM BUX Connector (JFP2/SNMP) Pin Signal 1 SMB_DATA 2 SMB_CLK B.15 HD Link connector (HDAUD1) Table B.15: HD Link Connector (HDAUD1) Pin Signal Pin Signal 1 VCC 2 GND 3 Sync 4 BITCLK 5 SDOUT 6 SDIN0 7 SDIN1 8 AC-RST 9 +12V 10 GND 11 GND 12 N/C 81 PCA-6011 User Manual Appendix B I/O Pin Assignments B.
B.16 LAN LED Connector (LAN LED1) 1 3 5 7 9 2 4 6 8 Table B.16: LAN LED Connector (LANLED1) Pin Signal 1 #LAN1_ACT 2 #LAN2_ACT 3 VCC3_LANLED1 4 VCC#_LANLED2 5 LAN1_1000# 6 LAN2_1000# 7 LAN1_LED0 8 LAN2_LED0 9 VCC 3SB B.17 AT Power Connector (ATXF1) 1 2 Table B.
Table B.18: H/W Monitor Alarm (JOBS1) Pin Signal 1 OBS_BEEP 2 ERR_BEEP B.19 USB Connector (USB12, USB34, USB56, USB78) Table B.19: USB Connector (USB12, USB34, USB56, USB78) Pin Signal Pin Signal 1 +5V 2 +5V 3 UV- 4 UV- 5 UV+ 6 UV+ 7 GND 8 GND 9 N/C 10 GND B.20 Case Open Connector (JCASE1) Table B.20: Case Open Connector (JCASE1) Pin Signal 1 CASEOP# 2 GND 83 PCA-6011 User Manual Appendix B I/O Pin Assignments B.
B.21 GPIO Pin Header (GPIO1) Table B.21: GPIO Pin Header (GPIO1) Pin Signal Pin Signal 1 GPIO_PORT80_1 2 GPIO_PORT80_5 3 VCC_GPIO 4 GND 5 GPIO_PORT80_2 6 GPIO_PORT80_6 7 GND 8 GND 9 GPIO_PORT80_3 10 GPIO_PORT80_7 11 GND 12 GND 13 GPIO_PORT80_4 14 GPIO_PORT80_8 B.22 System I/O Ports Table B.22: System I/O Ports Addr.
Appendix B I/O Pin Assignments Table B.22: System I/O Ports C90-C97 COM5 C98-C9F COM6 4D0-4D1 Interrupt Controller CF9 Reset Generator B.23 DMA Channel Assignments Table B.23: DMA Channel Assignments Channel Signal 0 Available 1 Available 2 Floppy disk (8-bit transfer) 3 Available 4 Cascade for DMA controller 1 5 Available 6 Available 7 Available B.24 Interrupt Assignments Table B.
B.25 1st MB Memory Map Table B.25: 1st MB Memory Map Addr. range (Hex) Device E0000h - FFFFFh BIOS D0000h - DFFFFh Unused C0000h - CFFFFh VGA BIOS A0000h - BFFFFh Video Memory 00000h - 9FFFFh Base memory B.26 PCI Bus Map Table B.
Appendix B I/O Pin Assignments PCA-6011 User Manual 87
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
