User`s manual
Table Of Contents
- Contents
- Chapter 1 Hardware Configuration
- Chapter 2 Connecting Peripherals
- 2.1 Introduction
- 2.2 1st (CN1) IDE Connectors
- 2.3 Floppy Drive Connector (CN3)
- 2.4 Parallel Port (CN4)
- 2.5 USB Ports (CN6,CN63,CN66,CN67)
- 2.6 VGA Connector CN7
- 2.7 DVI Connector VCN1 (optional)
- 2.8 Ethernet Connector (CN24)
- 2.9 Serial Ports (COM1: CN9/CN91; COM2: CN10 )
- 2.10 PS/2 Keyboard/Mouse Connector (CN11)
- 2.11 External Keyboard Connector (CN12)
- 2.12 CPU Fan Connector (CN68)
- 2.13 Front Panel Connectors (CN16, 17, 18, 19, 21&29)
- 2.14 ATX Feature Connector (CN20)
- 2.15 AC-97 Audio Interface (CN43)
- 2.16 Serial ATA Interface (SA0,SA1,SA2, and SA3)
- 2.17 Connecting to SNMP-1000 Remote Manager
- 2.18 Auxiliary 4-pin Power Connector (ATX1)
- 2.19 SCSI Daughterboard Extension Connector (CN30)
- 2.20 Case Open Connector (CN64)
- 2.21 Front Panel LAN Indicator Connector (CN65)
- 2.22 GPIO Pin Header (CN93)
- Chapter 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- Figure 3.3: Advanced BIOS features screen
- 3.4.1 CPU Features
- 3.4.2 Hard Disk Boot Priority
- 3.4.3 Virus Warning
- 3.4.4 CPU L1 & L2 Cache
- 3.4.5 Hyper-Threading Technology
- 3.4.6 Quick Power On Self Test
- 3.4.7 First/Second/Third Boot Device
- 3.4.8 Boot Other Device
- 3.4.9 Swap Floppy Drive
- 3.4.10 Boot Up Floppy Seek
- 3.4.11 Boot Up NumLock Status
- 3.4.12 Gate A20 Option
- 3.4.13 Typematic Rate Setting
- 3.4.14 Typematic Rate (Chars/Sec)
- 3.4.15 Typematic Delay (msec)
- 3.4.16 Security Option
- 3.4.17 APIC Mode
- 3.4.18 MPS Version Control For OS
- 3.5 Advanced Chipset Features
- Figure 3.4: Advanced chipset features screen
- 3.5.1 DRAM Timing Selectable
- 3.5.2 CAS Latency Time
- 3.5.3 DRAM RAS# to CAS# Delay
- 3.5.4 DRAM RAS# Precharge
- 3.5.5 Precharge Delay (t RAS)
- 3.5.6 System Memory Frequency
- 3.5.7 System BIOS Cacheable
- 3.5.8 Video BIOS Cacheable
- 3.5.9 Memory Hole At 15M-16M
- 3.5.10 PCI-Express Root Port Func
- 3.5.11 On-Chip Video Memory Size
- 3.5.12 On-Chip Frame Buffer Size
- 3.5.13 FIXED Memory Size
- 3.5.14 DVMT Memory Size
- 3.5.15 Init Display First
- 3.6 Integrated Peripherals
- Figure 3.5: Integrated peripherals
- Figure 3.6: On-Chip IDE Device
- 3.6.1 IDE HDD Block Mode
- 3.6.2 IDE DMA Transfer Access
- 3.6.3 On-Chip IDE Device
- 3.6.4 SATA Mode
- 3.6.5 On-Chip Serial ATA
- 3.6.6 PATA IDE Mode
- 3.6.7 SATA Port
- Figure 3.7: Onboard Device
- 3.6.8 USB Controller
- 3.6.9 USB 2.0 Controller
- 3.6.10 USB Keyboard/Mouse Support
- 3.6.11 AC97 Audio
- 3.6.12 Onboard LAN1 Control
- 3.6.13 Onboard LAN2 Control
- 3.6.14 GPIO Function
- Figure 3.8: Super I/O Device
- 3.6.15 KBC Input Clock
- 3.6.16 Onboard FDC Controller
- 3.6.17 Onboard Serial Port 1
- 3.6.18 Onboard Serial Port 2
- 3.6.19 UART Mode Select
- 3.6.20 RxD, TxD Active
- 3.6.21 IR Transmission Delay
- 3.6.22 UR2 Duplex Mode
- 3.6.23 Use IR Pins
- 3.6.24 Onboard Parallel Port
- 3.6.25 Parallel Port Mode
- 3.6.26 EPP Mode Select
- 3.6.27 ECP Mode Use DMA
- 3.7 Power Management Setup
- Figure 3.9: Power management setup screen (1)
- 3.7.1 Power Supply Type
- 3.7.2 ACPI Function
- 3.7.3 Power Management
- 3.7.4 Video Off Method
- 3.7.5 Video Off In Suspend
- 3.7.6 Suspend Type
- 3.7.7 Modem Use IRQ
- 3.7.8 Suspend Mode
- 3.7.9 Soft-Off by PWR-BTTN
- 3.7.10 CPU THRM-Throttling
- 3.7.11 PowerOn by Modem
- 3.7.12 PowerOn by LAN
- 3.7.13 PowerOn by Alarm
- 3.7.14 Primary IDE 0 (1) and Secondary IDE 0 (1)
- 3.7.15 FDD, COM, LPT PORT
- 3.7.16 PCI PIRQ [A-D]#
- 3.7.17 PWRON After PWR-Fail
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Frequency / Voltage Control
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit Without Saving
- Chapter 4 Chipset Software Install Utility
- Chapter 5 VGA Setup
- Chapter 6 LAN Configuration
- Chapter 7 USB 2.0 Configuration
- Chapter 8 Onboard Security Setup
- Appendix A Programming the watchdog
- Appendix B Programming the GPIO
- Appendix C Pin Assignments
- C.1 IDE Hard Drive Connector (CN1)
- C.2 Floppy Drive Connector (CN3)
- C.3 Parallel Port Connector (CN4)
- C.4 USB Connector (CN6, CN63, CN66, CN67)
- C.5 VGA Connector (CN7)
- C.6 VCN1 DVI connector
- C.7 COM1/COM2 RS-232 Serial Port (CN9/CN91/CN10)
- C.8 Keyboard and Mouse Connnector (CN11)
- C.9 External Keyboard Connector (CN68)
- C.10 CPU Fan Power Connector (CN14)
- C.11 Power LED (CN16)
- C.12 External Speaker Connector (CN17)
- C.13 Reset Connector (CN18)
- C.14 HDD LED Connector (CN19)
- C.15 ATX Feature Connector (CN20)
- C.16 ATX Soft Power Switch (CN21))
- C.17 H/W Monitor Alarm (CN22)
- C.18 AC-97 Audio Interface (CN43)
- C.19 SM Bus Connector (CN29)
- C.20 Case Open Connector (CN64)
- C.21 Front Panel LAN Indicator connector (CN65)
- C.22 GPIO Pin Header (SMD pitch=2.0mm) (CN93)
- C.23 System I/O Ports
- C.24 DMA Channel Assignments
- C.25 Interrupt Assignments
- C.26 1st MB Memory Map
- C.27 PCI Bus Map
vii
1.0.2 Initial Inspection
Before you begin installing your single board computer, please make sure
that the following materials have been shipped:
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
We have carefully inspected the PCA-6190 mechanically and electrically
before shipment. It should be free of marks and scratches and in perfect
working order upon receipt.
As you unpack the PCA-6190, check it for signs of shipping damage.
(For example, damaged box, scratches, dents, etc.) If it is damaged or it
fails to meet the specifications, notify our service department or your
local sales representative immediately. Also notify the carrier. Retain the
shipping carton and packing material for inspection by the carrier. After
inspection, we will make arrangements to repair or replace the unit.
1.0.3 Release Note
1 PCA-6190 Pentium 4/Celeron Dprocessor-based single board computer
1 PCA-6190 Startup Manual
1 CD with driver utility and manual (in PDF format)
1 FDD cable P/N: 1700340640
1 Ultra ATA 66/100 HDD cables P/N: 1701400452
4 Serial ATA HDD data cable P/N: 1700071000
4 Serial ATA HDD power cable P/N: 1703150102
1 ATX 12V power converter cable P/N: 170304015K
1 Printer (parallel) port & COM port cable kit P/N: 1700060305
1 Dual COM port cable kit (certain models) P/N: 1701092300
1 Y cable for PS/2 keyboard and PS/2 mouse P/N: 1700060202
2 Four-USB port cables P/N:1700000719
Jumper pack P/N:9689000068
DVI cable (PCA-6190G2-D0A1 only) P/N: 1700000821
Warranty card
Date Revision Description
September 2005 1st Edition Initial Release