User`s manual
Table Of Contents
- Contents
- Chapter 1 Hardware Configuration
- Chapter 2 Connecting Peripherals
- 2.1 Introduction
- 2.2 1st (CN1) IDE Connectors
- 2.3 Floppy Drive Connector (CN3)
- 2.4 Parallel Port (CN4)
- 2.5 USB Ports (CN6,CN63,CN66,CN67)
- 2.6 VGA Connector CN7
- 2.7 DVI Connector VCN1 (optional)
- 2.8 Ethernet Connector (CN24)
- 2.9 Serial Ports (COM1: CN9/CN91; COM2: CN10 )
- 2.10 PS/2 Keyboard/Mouse Connector (CN11)
- 2.11 External Keyboard Connector (CN12)
- 2.12 CPU Fan Connector (CN68)
- 2.13 Front Panel Connectors (CN16, 17, 18, 19, 21&29)
- 2.14 ATX Feature Connector (CN20)
- 2.15 AC-97 Audio Interface (CN43)
- 2.16 Serial ATA Interface (SA0,SA1,SA2, and SA3)
- 2.17 Connecting to SNMP-1000 Remote Manager
- 2.18 Auxiliary 4-pin Power Connector (ATX1)
- 2.19 SCSI Daughterboard Extension Connector (CN30)
- 2.20 Case Open Connector (CN64)
- 2.21 Front Panel LAN Indicator Connector (CN65)
- 2.22 GPIO Pin Header (CN93)
- Chapter 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- Figure 3.3: Advanced BIOS features screen
- 3.4.1 CPU Features
- 3.4.2 Hard Disk Boot Priority
- 3.4.3 Virus Warning
- 3.4.4 CPU L1 & L2 Cache
- 3.4.5 Hyper-Threading Technology
- 3.4.6 Quick Power On Self Test
- 3.4.7 First/Second/Third Boot Device
- 3.4.8 Boot Other Device
- 3.4.9 Swap Floppy Drive
- 3.4.10 Boot Up Floppy Seek
- 3.4.11 Boot Up NumLock Status
- 3.4.12 Gate A20 Option
- 3.4.13 Typematic Rate Setting
- 3.4.14 Typematic Rate (Chars/Sec)
- 3.4.15 Typematic Delay (msec)
- 3.4.16 Security Option
- 3.4.17 APIC Mode
- 3.4.18 MPS Version Control For OS
- 3.5 Advanced Chipset Features
- Figure 3.4: Advanced chipset features screen
- 3.5.1 DRAM Timing Selectable
- 3.5.2 CAS Latency Time
- 3.5.3 DRAM RAS# to CAS# Delay
- 3.5.4 DRAM RAS# Precharge
- 3.5.5 Precharge Delay (t RAS)
- 3.5.6 System Memory Frequency
- 3.5.7 System BIOS Cacheable
- 3.5.8 Video BIOS Cacheable
- 3.5.9 Memory Hole At 15M-16M
- 3.5.10 PCI-Express Root Port Func
- 3.5.11 On-Chip Video Memory Size
- 3.5.12 On-Chip Frame Buffer Size
- 3.5.13 FIXED Memory Size
- 3.5.14 DVMT Memory Size
- 3.5.15 Init Display First
- 3.6 Integrated Peripherals
- Figure 3.5: Integrated peripherals
- Figure 3.6: On-Chip IDE Device
- 3.6.1 IDE HDD Block Mode
- 3.6.2 IDE DMA Transfer Access
- 3.6.3 On-Chip IDE Device
- 3.6.4 SATA Mode
- 3.6.5 On-Chip Serial ATA
- 3.6.6 PATA IDE Mode
- 3.6.7 SATA Port
- Figure 3.7: Onboard Device
- 3.6.8 USB Controller
- 3.6.9 USB 2.0 Controller
- 3.6.10 USB Keyboard/Mouse Support
- 3.6.11 AC97 Audio
- 3.6.12 Onboard LAN1 Control
- 3.6.13 Onboard LAN2 Control
- 3.6.14 GPIO Function
- Figure 3.8: Super I/O Device
- 3.6.15 KBC Input Clock
- 3.6.16 Onboard FDC Controller
- 3.6.17 Onboard Serial Port 1
- 3.6.18 Onboard Serial Port 2
- 3.6.19 UART Mode Select
- 3.6.20 RxD, TxD Active
- 3.6.21 IR Transmission Delay
- 3.6.22 UR2 Duplex Mode
- 3.6.23 Use IR Pins
- 3.6.24 Onboard Parallel Port
- 3.6.25 Parallel Port Mode
- 3.6.26 EPP Mode Select
- 3.6.27 ECP Mode Use DMA
- 3.7 Power Management Setup
- Figure 3.9: Power management setup screen (1)
- 3.7.1 Power Supply Type
- 3.7.2 ACPI Function
- 3.7.3 Power Management
- 3.7.4 Video Off Method
- 3.7.5 Video Off In Suspend
- 3.7.6 Suspend Type
- 3.7.7 Modem Use IRQ
- 3.7.8 Suspend Mode
- 3.7.9 Soft-Off by PWR-BTTN
- 3.7.10 CPU THRM-Throttling
- 3.7.11 PowerOn by Modem
- 3.7.12 PowerOn by LAN
- 3.7.13 PowerOn by Alarm
- 3.7.14 Primary IDE 0 (1) and Secondary IDE 0 (1)
- 3.7.15 FDD, COM, LPT PORT
- 3.7.16 PCI PIRQ [A-D]#
- 3.7.17 PWRON After PWR-Fail
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Frequency / Voltage Control
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit Without Saving
- Chapter 4 Chipset Software Install Utility
- Chapter 5 VGA Setup
- Chapter 6 LAN Configuration
- Chapter 7 USB 2.0 Configuration
- Chapter 8 Onboard Security Setup
- Appendix A Programming the watchdog
- Appendix B Programming the GPIO
- Appendix C Pin Assignments
- C.1 IDE Hard Drive Connector (CN1)
- C.2 Floppy Drive Connector (CN3)
- C.3 Parallel Port Connector (CN4)
- C.4 USB Connector (CN6, CN63, CN66, CN67)
- C.5 VGA Connector (CN7)
- C.6 VCN1 DVI connector
- C.7 COM1/COM2 RS-232 Serial Port (CN9/CN91/CN10)
- C.8 Keyboard and Mouse Connnector (CN11)
- C.9 External Keyboard Connector (CN68)
- C.10 CPU Fan Power Connector (CN14)
- C.11 Power LED (CN16)
- C.12 External Speaker Connector (CN17)
- C.13 Reset Connector (CN18)
- C.14 HDD LED Connector (CN19)
- C.15 ATX Feature Connector (CN20)
- C.16 ATX Soft Power Switch (CN21))
- C.17 H/W Monitor Alarm (CN22)
- C.18 AC-97 Audio Interface (CN43)
- C.19 SM Bus Connector (CN29)
- C.20 Case Open Connector (CN64)
- C.21 Front Panel LAN Indicator connector (CN65)
- C.22 GPIO Pin Header (SMD pitch=2.0mm) (CN93)
- C.23 System I/O Ports
- C.24 DMA Channel Assignments
- C.25 Interrupt Assignments
- C.26 1st MB Memory Map
- C.27 PCI Bus Map
13
1.8.3 Watchdog timer output (J2)
The PCA-6190 contains a watchdog timer that will reset the CPU or send
a signal to IRQ11 in the event the CPU stops processing. This feature
means the PCA-6190 will recover from a software failure or an EMI
problem. The J2 jumper settings control the outcome of what the com-
puter will do in the event the watchdog timer is tripped.
1.9 System Memory
The PCA-6190 has four sockets for 240-pin dual inline memory modules
(DIMMs) in two separated memory channels. It can operate with single
channel or dual channel modules. We recommend to use dual channel
mode to provide optimized performance.
All these sockets use 1.8 V unbuffered double data rate synchronous
DRAMs (DDRII SDRAM). They are available in capacities of 256, 512
and 1024 MB. The sockets can be filled in any combination with DIMMs
of any size, giving a total memory size between 256 MB and 4 GB.
Table 1.4: Watchdog timer output (J2)
Function
Jumper Setting
IRQ11
* Reset
* default setting
Note: The interrupt output of the watchdog timer is a
low level signal. It will be held low until the
watchdog timer is reset.
1
1-2 closed
1
2-3 closed