Mobile Computer MIT-W102XXXXXXXXXXXXXXXX User Manual Ver 1.
Copyright The documentation and the software included with this product are copyrighted 2020 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE Conformity Statement Radio products with the CE alert marking comply with the RED Directive (2014/53/EU) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards).
used with an accessory that contains metal may not ensure compliance with FCC RF exposure guidelines. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy.
– Product name and serial number – Description of your peripheral attachments – Description of your software (operating system, version, application software, etc.) – A complete description of the problem – The exact wording of any error messages Details of preparatory treatment or disposal Installation is only to be carried out by manufacturer authorized and trained personnel. Regarding calibrating the device, we suggest to send back the tablet to the supplier for annually check. Safety Instructions 1.
d. The equipment does not work well or you cannot get it to work according to user manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 16. CAUTION: The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard used batteries according to the manufacturer’s instructions. 17.
or signal output part is configuring a medical system, and is therefore, responsible that the system complies with the requirements of the system standard IEC 60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified equipment in the patient environment and IEC 60XXX certified equipment outside of the patient environment. If in doubt, consult the technical services department or your local representative. 27.
pas de détergents liquides ou en aérosol pour le nettoyage. 4. Pour les équipements enfichables, la prise de courant doit être située à proximité de l'équipement et doit être facilement accessible. 5. Gardez cet équipement à l'abri de l'humidité. 6. Placez cet équipement sur une surface fiable pendant l'installation. Le faire tomber ou le laisser tomber peut causer des dommages. 7. Les ouvertures sur le boîtier sont destinées à la convection d'air. Protégez l'équipement contre la surchauffe.
du fabricant. 17. Si votre ordinateur perd du temps de manière significative ou si la configuration du BIOS se réinitialise aux valeurs par défaut, la batterie peut ne pas être alimentée. Mise en garde! 1. Ne remplacez pas la batterie vous-même. Veuillez contacter un technicien qualifié ou votre revendeur. 2. L'ordinateur est équipé d'un circuit d'horloge en temps réel alimenté par batterie. Il existe un risque d'explosion si la pile n'est pas remplacée correctement.
doivent être conformes à la norme système CEI 60601-1-1. Quiconque connecte un équipement supplémentaire à la partie d'entrée de signal ou à la partie de sortie de signal configure un système médical et est donc responsable de la conformité du système aux exigences de la norme système CEI 60601-1-1. L'unité est destinée à une interconnexion exclusive avec un équipement certifié CEI 60601-1 dans l'environnement du patient et un équipement certifié CEI 60XXX en dehors de l'environnement du patient.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Do not place the battery incorrectly as this may cause danger of explosion. Dispose of used batteries according to the manufacturer's instructions. Do not dispose of batteries in a fire. They may explode. Check with local authorities for disposal instructions. Battery Pack Caution The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, heat above 40°C, or incinerate.
1.3 Package Contents ...................................................................................................... 15 1.4 System Configuration ................................................................................................ 16 1.6 Exploring the MIT-W102 ............................................................................................ 18 1.6.1 Front View .......................................................................... 18 1.6.2 Rear View ..........................
5.1 Checking Battery Status ........................................................................................... 42 5.2 Maintenance ............................................................................................................... 42 5.2.1 Maintaining the Battery ........................................................... 42 5.2.2 Maintaining the LCD Display ...................................................... 43 5.2.3 Cleaning the MIT-W102 .............................................
Chapter 1 Ready to Go Congratulations on your purchase of the MIT-W102 Rugged Tablet PC. This product combines rugged design with reliable performance and powerful functionality to best suit all your needs, in a wide range of working conditions. This user manual outlines all you need to know to set up and use your MIT-W102.
http://www.advantech.com.tw/ 1.1 Symbols Used in this Manual Denotes information that must be observed. Failure to do so may result in personal harm or damage to the product. Denotes information that must be observed. Failure to do so may result in personal harm or damage to the product. 1.2 Product Features • Rugged design. • Featuring with the Future Intel® Pentium ™ processor for intelligent system. • Built-in WLAN/Bluetooth/NFC • Durable, shock-resistant magnesium alloy housing. • 10.
• MIT-W102 Tablet PC • AC power adaptor • Battery Pack Warning! To prevent electric shock, Do not remove cover. Warning! 1. Input voltage rated 100-250 VAC, 50-60 Hz, 1.5-0.75 A, Output Voltage rated 19 VDC , max 3.15 A 2. Use a 11 Vdc @ 2860 mA lithium battery 3. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator Caution! 1. Do not replace battery yourself. Please contact a qualified technician or your retail provider. 2.
1.6 Exploring the MIT-W102 1.6.1 Front View No. Component 1 P1 – Programmable Button 2 P2 - Programmable Button 3 Front Camera 4 Power button 5 Connected to expansion module 6 DC-in jack 7 Docking connector 8 Projective capacitive multiple touch screen 9 I/O ports • USB 3.0 x 1 • USB 2.
• Audio x 1 10 Connectivity LED indicator • Blue: when Wi-Fi is Turned on • Green: when BT is Turned on 11 HDD LED indicator • Blinking blue: when hard disk drive is working 12 Power / Battery LED indicator • Green: Battery is fully charged (>95%) • Amber : Battery is charging or Battery life is lower than 10% 1.6.2 Rear View No.
7 NFC 1.6.3 Right View No. 1 Component Connected pin for expansion module 1.6.4 Left View 4 No.
3 USB 3.0 4 USB 2.0 5 Micro HDMI 1.6.5 Top View No. Component 1 Function buttons 2 Built-in MIC 3 Power button 1.6.6 Bottom View No.
Chapter 2 Making Connections 22
2.1 Connecting the Power Before you can use your MIT-W102, you must fully charge the battery. Connect the power adapter as shown and leave to charge for: • A minimum of 2 hours when using the internal battery Condition: the operation time is based on the LCD backlight at 50% and the average utilization of the system under 10%. Installation Procedures: 1. Connect the female end of the power adapter to the DC-in of MIT-W102. 2. Connect the female end of the power cord to the DC power adapter. 3.
2.3 Connecting USB Devices You can connect peripheral devices, such as a USB keyboard and mouse, as well as other wireless devices using the USB ports on the left side of the MIT-W102. 2.4 Connecting Headphones You can connect a pair of headphones using the headphone jack on the left side of the MIT-W102.
2.5 Connecting a Microphone The MIT-W102 features a built-in microphone, but you can still connect an external microphone if needed. Connect the microphone to the microphone jack on the left side of the MIT-W102 as shown.
Chapter 3 Turning On 26
1. Press and hold the power button to turn on the MIT-W102. 3.1 Controlling the MIT-W102 3.1.1 Using the Touch Screen The MIT-W102 is equipped with touch screen technology, for ease of use when you are on the go. Simply tap the screen with your finger to select icons and run applications. 3.1.2 Using the Tap Function When you tap on the screen with a pen or stylus, it emulates click functions of a regular mouse. • To emulate a left click single tap the screen once.
3.1.4 Using the On-Screen Keyboard 1. Press and hold on the taskbar. 2.
3. Tap the icon on the taskbar to open the keyboard 4. Use your finger or stylus pen to tap and enter letters, numbers and symbols as you would with a regular keyboard. To type capital letters tap the lock icon on the on-screen keyboard. a. To use handwriting, tap upper left button of On-Screen Keyboard.
b. Select the handwriting icon. c. Use your finger and stylus pen to write on screen.
3.1.5 Adjusting Screen Brightness 1. Tap on the right end of the taskbar to open the Action Center 2. Tap Brightness icon to adjust the brightness.
3.1.6 Adjusting the Volume 1. Tap the Volume icon on taskbar 2.
Chapter 4 Wireless Connections 33
4.1 Wi-Fi Connection Wi-Fi access requires a separate purchase of a service contract with a wireless service provider. Contact a wireless service provider for more information. The MIT-W102 comes pre-loaded with WLAN module; you can send and receive signals to a Wi-Fi network then synchronize files. A wireless network can be added either when the network is detected or by manually entering settings information. Before doing these steps, determine if authentication information is needed. 1.
3. Available wireless access points will be shown once Wi-Fi is enabled. 4. Select the access point to connect with.
5. You may be prompted to enter a Security key for secure access. 6. The wireless connection is negotiated and the icon in the notification area shows a connected status whenever a wireless connection is present. 7.
4.2 Bluetooth Connections The MIT-W102 comes with built-in Bluetooth functionality that allows you to connect and communicate with other Bluetooth-enabled devices. 4.2.1 Setting Up Bluetooth Follow these instructions to set up a Bluetooth connection. 1. Type Bluetooth in Search and tap “Bluetooth and other devices settings” 2.
3. When enabled, Bluetooth icon will be shown on the taskbar 4.
5. Select “Bluetooth” 6.
7. Comparing MIT-W102 with the Bluetooth device with Pass Key Entered 8. The Bluetooth device is successfully connected with MIT-W102 when the process is completed. It is recommended that you use a passkey to prevent unauthorized access to your MIT-W102.
Chapter 5 Advance Setting 41
5.1 Checking Battery Status As it is likely you will be using your MIT-W102 when out and about, it is important that you monitor the battery status regularly, to ensure you do not run out of power at a critical moment. 1. Tap on the Power icon on the taskbar to view detailed information and the battery screen appears. Best performance – Favors performance over power Best battery life – Saves energy by reducing MIT-W102’s performance. 5.
• Keep the battery out of reach of children. • Dispose of used batteries according to local regulations. 5.2.2 Maintaining the LCD Display • Do not scratch the surface of the screen with any hard objects. • Do not spray liquid directly on the screen or allow excess liquid to drip down inside the device. • Do not place anything, such as food and drink, on the screen at any time to prevent damage to the screen.
Symptoms, photo or video if available. Guidance and manufacturer’s declaration – electromagnetic emissions The model MIT-W102 SERIES is intended for use in the electromagnetic environment specified below. The customer or the user of the model MIT-W102 SERIES should assure that it is used in such an environment. Emissions test Electromagnetic environment – Compliance guidance RF emissions The model MIT-W102 SERIES uses RF CISPR 11 energy only for its internal function.
10 3,8 3,8 7,3 100 12 12 23 For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations.
Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than the compliance level in each frequency range. b Interference may occur in the vicinity of equipment marked with the following symbol: NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
Chapter 6 Dashboard and Hotkey setting 47
6.1 Dashboard Click on the shortcut to launch the dashboard 6.2 NFC 6.2.
6.2.
(3) Select Card Type (4) Polling Start 50
6.2.3 NFC Usage NFC card can be detected when approaching the right hand side of the device 6.
(3) Switch Front / Rear Camera (Click camera icon to switch camera) (4) Video Recording .
(5) Click setting icon to change file name and path.
6.
6.5 Hotkey Setting Click Hot Key Mode Setting and select function. E.g.: Set P1 key as WiFi ON / OFF key.
Appendix Specifications 56
A.1 Specifications Feature Description Operating System Microsoft Windows 10 IoT Enterprise LTSC Processor Intel® Pentium® Processor N4200 Max. speed Quad Core 1.1GHz ( Burst Frequency : 2.5GHz) Memory LPDDR4 1600MHz 4GB on board memory Storage 1 x m.2 SSD (Default 64GB / supports up to 128GB) Display 10.1” WUXGA TFT LCD Touch Panel P-CAP Multiple Touch One Power button Application Button Two Function programmable buttons for quick selection of applications 802.
Feature Security Description 1. Password security 2. TPM 2.0 One USB 3.0/ 2.0 One USB 2.0 One HP/MIC combined jack I/O Ports One Micro HDMI type D One DC-in jack One Expansion port 8-pin One Docking port 32-pin Audio Output Physical One 1 watt speaker 295 x 196 x 20mm Approx. 1.1Kg (base configuration); approx. 2.
LED Status DUT AC Internal Green Amber on/off adapter Battery LED LED Remark in Off X X Off Off System Off Off V V Off On Battery is charging Off V V On Off On V V Off On On V V On Off On V V Off On Battery is fully charged (100%) Battery is charging Battery is fully charged (100%) Battery Low (< 10 %) A.2 Optional Accessories A.2.1 External Battery You can use an external battery to extend the power of your MIT-W102. Battery specification: 2860 mAh, 11.1V A.2.
2. Lock to secure the battery once it is properly to be inserted. A.2.1.2 Removing the External Battery Repeat the above steps in reverse order to remove the battery. A.2.2 Office Docking Station You can use the office docking stand to dock the MIT-M101 when you are at your home or on your office desk. When docked, you can charge both the internal and external batteries or transfer data from your MIT-M101 to another PC.
Attach the MIT-M101 to the docking stand as shown. To charge the external battery, attach the battery to the docking stand as shown below. The external battery can also be charged when installed on the MIT-M101.
A.2.2.1 Docking Connectors See below for the rear view of the docking and a description of all ports and connectors. No. Component Function 1 Power jack Connect an RJ-45 cable to access LAN connection. 2 LAN port Connect a serial cable to connect to another PC. 3 USB port Connect USB connectors to transfer data. 4 VGA port Connect the AC adapter to charge the battery. 5 COM port Connect two devices (Input / Output).
No. Function 1 Lock mechanism (quick load/unload) 2 USB port 3 Microphone jack 4 Headphone jack (Earphone Jack) 5 Dock detection LED 6 Battery bay status LED A.2.2.2 Connecting Power to the Docking Connect the AC power adapter to the docking and the mains as shown below. A.2.2.3 Docking Specifications Feature Description Feature Description Product Name MIT-W102 Docking Station Model Number MIT-W102-ACCDS One LAN port One COM port External I/O Interfaces One VGA port Two USB 2.
A.2.3 VESA Docking Station You can use the VESA docking station to dock the MIT-W102 to the place where you need via standard 75 x 75 mm VESA hole on rear side. When docked, you can transfer data from your MIT-W102 to another PC by COM port or USB port. Attach the MIT-W102 to the docking stand as shown. A.2.3.1 Docking Connectors See below for the rear view of the docking and a description of all ports and connectors.
No. Component Function 1 Power jack Connect the AC adapter to provide power. 2 LAN port Connect an RJ-45 cable to access LAN connection. 3 VGA port Connect to display for 2nd display output 4 COM port Connect a serial cable to connect to another PC. 5 USB port USB 2.0 port x 2 , Connect USB connectors to transfer data. See below for the front view of the docking and a description of all ports and connectors. No.
A.2.3.3 Docking Specifications Feature Description Feature Description Product Name MIT-W102 VESA Docking Model Number MIT-W102-ACCVD One LAN port One COM port External I/O Interfaces One VGA port Two USB 2.0 host connectors One DC-in Power Physical Size AC Adapter: AC 100V-250V 50/60Hz,1.5A(max) Output : 19Vdc/3.15A(max)/60W 224.7 (H) x 200 (W) x 56.4 (D) mm A.2.
A.2.4.1 Attaching the Adjustable Stand 1. Fasten four screws to attach the 3-in-1 multi-functional back cover to your MIT-M101 with or without rubber bumpers attached to the tablet. 2. Pull to adjust the stand to desirable angle.
A.2.4.2 How to install the hand strap on the stand 1. Pass the end of the hand strap through the outer hole on each side of the stand 2. Pass the end of the hand strap through the inner hole on each side of the stand and stick the hand strap together 3. Check if the length of the hard strap is OK.
A.2.5 Rubber Bumper A.2.5.1 Installing the Rubber Bumpers To protect the housing case of MIT-W102, install the rubber bumpers. 1. Install the rubber bumpers on the left and right side of the MIT-W102. 2. Make sure the rubber bumpers are aligned and locked on the indents. 3. Screw the rubber bumpers on left and right properly into the MIT-W102. The Rubber bumper could provide well drop protection when device fall from high place.
A.2.5.2 Removing the Rubber Bumpers 1. Unscrew the rubber bumpers from the rear of the tablet PC. 2. Remove the rubber bumpers on the left and right.
A.3 Installing SSD Inserting SSD You can insert an SDD to store data, which needs to be later transferred to another machine, or to simply expand the storage capacity of the MIT-W102. 1. Open the SSD card compartment cover. 2. Insert the SDD, facing upwards, until it clicks into place. Screw and fix SSD 3. Screw and fix the shielding case.
4. Close the SDD compartment cover. Removing SSD 1. Open the SSD compartment cover. 2.
3. Unscrew and remove SSD from the slot. 4. Close and screw the SSD card compartment cover.
