User Manual MIO-5251 Intel® Celeron® J1900 & Atom™ E3825, 3.
Copyright The documentation and the software included with this product are copyrighted 2014 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 x MIO-5251 SBC 1 x SATA Cable 30cm (p/n: 1700006291) 1 x SATA Power Cable 35cm (p/n: 1700018785) 1 x Audio Cable 20cm (p/n: 1700019584) 2 x COM Cable 22cm (p/n: 1701200220) 1 x Heatsink (19mm) (p/n: 1960062791T001) 1 x Startup manual (p/n: 2006525100) 1 x Mini Jumper(10pcs package) (p/n: 9689000002) 1 x Screw Kit (4pcs screws for miniPCIe) (p/n: 96
MIO-5251 User Manual vi
Contents Chapter 1 General Information ............................1 1.1 1.2 Introduction ............................................................................................... 2 Specifications ............................................................................................ 2 1.2.1 Functional Specifications .............................................................. 2 1.2.2 OS support.................................................................................... 4 1.2.
Appendix B System Assignments........................ 63 B.1 System I/O Ports..................................................................................... 64 Table B.1: System I/O Ports ...................................................... 64 1st MB Memory Map............................................................................... 64 Table B.2: 1st MB Memory Map ................................................ 64 Interrupt Assignments ......................................................
Chapter 1 1 General Information This chapter gives background information on the MIO-5251.
1.1 Introduction MIO-5251 is designed using MI/O Extension form factor (compact series, 146 x 102 mm) and powered by the latest generation of Intel® Celeron® J1900 and Atom™ E3825 processors which have low power features but also good performance computing, especially for multimedia capabilities compared to earlier generations. Meanwhile, MIO-5251 offers flexible expansion possibilities: two full-size mini PCIe, 2nd LVDS through MIOe-230, SD card, SIM holder, MIOe with PCIex1, SMBus, 3xUSB2.
– Specification and Resolution * VGA: 2560 x 1600 at 60Hz * HDMI/DisplayPort: HDMI 1.4a with audio, up to 1080P at 60Hz. DisplayPort is supported standard version 1.1a with audio, up to 2560x1600 at 60Hz * LVDS/eDP: 48-bit dual channel LVDS up to WUXGA 1920x1200 at 60Hz via Gigabit Ethernet – Controller: Intel® i210 * 10/100/1000 BASE-T * IEEE 802.3az Energy Efficient Ethernet (EEE), which defines Low Power Idle (LPI) state * IEEE 1588/802.1AS precision time synchronization * 9.
– SD slot: supported by T-P/N, shared the location with mSATA High Definition Audio: – Intel® High Definition Audio Interface – High Definition Audio Codec with Realtek proprietary loss-less content protection technology – Supports 1 Line-input, 1 Line output, 1 Mic-input BIOS – AMI UEFI 64 Mbit, BIOS for 64 or 32bit is different, default version is for 64bit – Default setting is Legacy boot, that can be manually changed to UEFI boot. If default setting to UEFI is needed, that can be done by T-P/N 1.
Chapter 1 1.3 Block Diagram General Information 65.50 64.27 59.19 46 39.85 28.45 27 25.02 17.30 12.11 8.34 5.18 3.30 0 122.38 146 142.70 140.66 1.4 Board layout: dimensions 102 98.70 102 97.05 92.70 70.10 86.70 76 60.13 51.67 27.20 27.73 20.50 11.06 8.37 15.19 6.50 3.30 0 34.06 65.50 56.10 69.96 85.70 99.56 119.70 0 146 142.70 142.48 137.70 0 Figure 1.
6 128.63 107.63 112.43 89.93 77.65 0 5.58 102 102 84.03 85.94 2-M2-NUT 68.51 51.63 49.68 3.20 6-Ø 6-Ø 6 .4 LE HO 0 PA D 146 107.55 54.66 0 0 0 Figure 1.2 MIO-5251 Mechanical Drawing (Bottom Side) 30 Ø Ø 5. 25 3 156.14 Figure 1.
Chapter 2 2 Installation This chapter explains the setup procedures of the MIO-5251 hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all safety precautions before you begin the installation procedure.
2.1 Jumpers & Switches The MIO-5251 has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of the various jumpers. Table 2.1: Jumpers & Switches J2 Auto Power On J5 LCD Power SW2 Clear CMOS 2.2 Connectors Onboard connectors link the MIO-5251 to external devices such as hard disk drives, a keyboard, or floppy drives. The table below lists the function of each of the connectors. Table 2.
Chapter 2 2.3 Locating Connectors Installation Figure 2.1 MIO-5251 Connector Locations (Top Side) Figure 2.
2.4 Setting Jumpers You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper, you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Chapter 2 2.4.3 Clear CMOS (SW2) Table 2.
MIO-5251 User Manual 12
Chapter 3 AMI BIOS Setup 3
AMIBIOS has been integrated into a plethora of motherboards for decades. With the AMIBIOS Setup program, you can modify BIOS settings and control the various system features. This chapter describes the basic navigation of the MIO-5251 BIOS setup screens. AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This information is stored in battery-backed CMOS so it retains the Setup information when the power is turned off.
Turn on the computer and check for the patch code. If there is a number assigned to the patch code, it means that the BIOS supports your CPU. If there is no number assigned to the patch code, please contact an Advantech application engineer to obtain an up-to-date patch code file. This will ensure that your CPU‘s system status is valid. After ensuring that you have a number assigned to the patch code, press and you will immediately be allowed to enter Setup.
3.1.2 Advanced BIOS Features Setup Select the Advanced tab from the MIO-5251 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screens is shown below. The sub menus are described on the following pages.
Chapter 3 3.1.2.1 ACPI Settings AMI BIOS Setup Enable ACPI Auto Configuration Enable or disable BIOS ACPI auto configuration. Enable Hibernation Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
3.1.2.2 Super I/O Configuration Serial Port 1 Configuration Set Parameters of Serial Port 1 (COMA). Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB). Serial Port 3 Configuration Set Parameters of Serial Port 3 (COMC). Serial Port 4 Configuration Set Parameters of Serial Port 4 (COMD).
Chapter 3 3.1.2.3 Embedded Controller Configuration AMI BIOS Setup EC Hardware Monitor This page display all information about system Temperature/Voltage/Current. iManager WatchDog IRQ This item allows users to set the IRQ number of EC watchdog. Backlight Enable Polarity This item allows users to set backlight mode. EC Power Saving Mode This item allows users to set board’s power saving mode when off. EC Watch Dog Function This item allows users to select EC watchdog timer.
3.1.2.4 S5 RTC Wake Settings Wake system from S5 Enable or disable System wake on alarm event. Select FixedTime, system will wake on the hr::min::sec specified.
Chapter 3 3.1.2.5 Serial Port Console Redirection AMI BIOS Setup Console Redirection This item allows users to enable or disable console redirection for Microsoft Windows Emergency Management Services (EMS). Console Redirection This item allows users to configuration console redirection detail settings.
3.1.2.6 CPU Configuration Limit CPUID Maximum Disabled for Windows XP. Execute Disable Bit XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3.) Hardware Prefetcher Enable the mid level cache(L2) streamer prefetcher. Adjacent Cache Line Prefetch Enable the mid level cache(L2) prefetching of adjacent cache lines.
Chapter 3 3.1.2.7 PPM Configuration AMI BIOS Setup CPU C state Report Enable/Disable CPU C state report to OS. Max CPU C-state This option controls Max C state that the processor will support. S0ix Enable/Disable CPU S0ix state.
3.1.2.8 IDE Configuration Serial-ATA (SATA) Enable / Disable Serial ATA. SATA Speed Support SATA Speed Support Gen1 or Gen2. SATA ODD Port SATA ODD is Port0 or Port1. SATA Mode Select IDE / AHCI. Serial-ATA Port 0 / Port1 Enable / Disable Serial ATA Port0 / Port1. SATA Port 0 / Port1 HotPlug Enable / Disable SATA Port0 / Port1 hotplug function.
Chapter 3 3.1.2.9 CSM Configuration AMI BIOS Setup CSM Support Enable/Disable CSM Support. GateA20 Active UPON REQUEST - GA20 can be disabled using BIOS services. ALWAYS - do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Option ROM Messages Set display mode for Option ROM. INT19 Trap Response BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE - execute the trap right away; POSTPONED - execute the trap during legacy boot.
3.1.2.10 Trusted Computing Trusted Computing Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
Chapter 3 3.1.2.11 USB Configuration AMI BIOS Setup Legacy USB Support Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. EHCI Hand-Off This is a workaround for OSes without EHCI hand-off support.
3.1.2.
Chapter 3 3.1.3 Chipset Configuration AMI BIOS Setup North Bridge Details for North Bridge items. South Bridge Details for South Bridge items.
3.1.3.1 North Bridge Intel IGD Configuration Config Intel IGD Settings. Max TOLUD Maximum Value of TOLUD.
Chapter 3 3.1.3.2 Intel IGD Configuration AMI BIOS Setup Primary IGFX Boot Display Select the Video Device which will be activated during POST. This has no effect if an external graphics present. Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display. LVDS Panel Type This item allow user to select LVDS panel type. DVMT Pre-Allocated Select DVMT 5.
3.1.3.3 South Bridge Azalia HD Audio Azalia HD Audio Options. USB Configuration USB Configuration Settings. PCI Express Configuration PCI Express Configuration settings. High Precision Timer Enables or disables the high precision timer. LAN1 Controller Enable or Disable the LAN1. LAN2 Controller Enable or Disable the LAN2. PCIE Wake Enable or Disable PCIE to wake the system from S5. Restore AC Power Loss Select AC power state when power is re-applied after a power failure.
Chapter 3 3.1.3.4 Azalia HD Audio AMI BIOS Setup Audio Controller Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled. Enabled = Azalia will be unconditionally Enabled. Auto = Azalia will be enabled if present disabled otherwise.
3.1.3.5 USB Configuration OS Selection OS Selection to choose Windows 8.X / Windows 7. XHCI Mode Mode of operation of xHCI controller. USB 2.0(EHCI) Support Control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enabled. USB Per Port Control Control each of the USB ports (0~3). Enable: Enable USB per port; Disable: Use USB port X settings.
Chapter 3 3.1.3.6 PCI Express Configuration AMI BIOS Setup PCI Express Port0 / Port2 Enable or Disable the PCI Express Port0 / Port 2 in the Chipset. Speed Configure PCIe Port Speed.
3.1.4 Security Select Security Setup from the MIO-5251 Setup main BIOS setup menu. All Security Setup options, such as password protection and virus protection are described in this section. To access the sub menu for the following items, select the item and press : Change Administrator / User Password Select this option and press to access the sub menu, and then type in the password.
Chapter 3 3.1.5 Boot AMI BIOS Setup Setup Prompt Timeout Number of seconds that the firmware will wait before initiating the original default boot selection. A value of 0 indicates that the default boot selection is to be initiated immediately on boot. A value of 65535(0xFFFF) indicates that firmware will wait for user input before booting. This means the default boot selection is not automatically started by the firmware. Bootup NumLock State Select the keyboard NumLock state.
3.1.6 Save & Exit Save Changes and Exit This item allows you to exit system setup after saving the changes. Discard Changes and Exit This item allows you to exit system setup without saving any changes. Save Changes and Reset This item allows you to reset the system after saving the changes. Discard Changes and Reset This item allows you to rest system setup without saving any changes. Save Changes This item allows you to save changes done so far to any of the options.
Chapter 4 MIOe Installation 4
The MI/O compact form factor SBC is a new-generation SBC design with a variety of mechanical improvements. Here is the quick installation guide for our thermal design and MIOe module installation. 4.1 Quick Installation Guide: 1. There is a Heatsink / Cooler in the white box inside the package. Carefully remove the release paper from the thermal pad before installation. Remove Release Paper PAD XR-Pe 13.9x13.9x1mm 2.
Appendix A A Pin Assignments This appendix contains information of a detailed or specialized nature.
A.1 Jumper List J2 Auto Power On Setting Part Number 1653002101 Footprint HD_2x1P_79_D Description PIN HEADER 2*1P 180D(M)SQUARE 2.0mm DIP W/O Pb Setting Function NC Power Button for Power On (1-2)* Auto Power On J5 LCD Power Part Number 1653003260 Footprint HD_3x2P_79 Description PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050 Setting Function (1-3)* +3.
CN1 12V Power Input Part Number 1655003865 Footprint WF_2x2P_165_BOX_RA_D_740SP Description ATX PWRCONN 2x2P 4.
CN6 SODIMMDDR3_204 Part Number 1651002088 Footprint SODIMMDDR3_204P_AS0A626-HA Description DDR3 SODIMM H=9.2mm 204P SMD AS0A626-HASN-7H CN7 Power Switch Part Number 1655302020 Footprint WF_2P_79_BOX_R1_D Description WAFER BOX 2P 2.0mm 180D(M) DIP A2001WV2-2P Pin Pin Name 1 PSIN 2 GND CN9 Reset Part Number 1655302020 Footprint WF_2P_79_BOX_R1_D Description WAFER BOX 2P 2.
GPIO Part Number 1653004099 Footprint HD_5x2P_79_23N685B-10M10 Description BOX HEADER 5x2P 2.00mm 180D(M) SMD 23N685B-10M10 Pin Pin Name 1 +5V 2 GPIO4 3 GPIO0 4 GPIO5 5 GPIO1 6 GPIO6 7 GPIO2 8 GPIO7 9 GPIO3 10 GND CN11 VGA Part Number 1654000055 Footprint DBVGA-VF5MS Description D-SUB Conn.
CN12 HDMI/DP Part Number 1654010203 Footprint HDMICON_21P_845-002-217CRL Description HDMI+DISPLAY Conn.
SATA Power Part Number 1655001154 Footprint WF_4P_98_BOX_R1_D Description WAFER BOX 4P 2.50mm 180D(M) DIP 24W1170-04S10-01 Pin Pin Name 1 +5V 2 GND 3 GND 4 +12V CN14 SATA Part Number 1654007578 Footprint SATA_7P_WATF-07DBN6SB1U Description Serial ATA 7P 1.
CN15 Mini PCIE Part Number 1654002538 Footprint FOX_AS0B226-S68K7F Description MINI PCI E 52P 6.8mm 90D SMD AS0B226-S68Q-7H Pin Pin Name 1 WAKE# 2 +3.3VSB 3 NC 4 GND 5 NC 6 +1.5V 7 NC 8 UIM_PWR 9 GND 10 UIM_DATA 11 REFCLK- 12 UIM_CLK 13 REFCLK+ 14 UIM_RESET 15 GND 16 UIM_VPP 17 NC 18 GND 19 NC 20 W_DISABLE# 21 GND 22 PERST# 23 PERn0 24 +3.3VSB 25 PERp0 26 GND 27 GND 28 +1.
NC 43 SEL 44 NC 45 NC 46 NC 47 NC 48 +1.5V Appendix A Pin Assignments 42 49 NC 50 GND 51 NC 52 +3.3VSB CN16 mSATA Part Number 1654002538 Footprint FOX_AS0B226-S68K7F Description MINI PCI E 52P 6.8mm 90D SMD AS0B226-S68Q-7H Pin Pin Name 1 NC 2 +3.3V 3 NC 4 GND 5 NC 6 +1.5V 7 NC 8 NC 9 GND 10 NC 11 NC 12 NC 13 NC 14 NC 15 GND 16 NC 17 NC 18 GND 19 NC 20 NC 21 GND 22 NC 23 B+ 24 +3.
25 B- 26 GND 27 GND 28 +1.5V 29 GND 30 SMB_CLK 31 A- 32 SMB_DAT 33 A+ 34 GND 35 GND 36 USB D- 37 GND 38 USB D+ 39 +3.3V 40 GND 41 +3.3V 42 NC 43 NC 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC 52 +3.
SIM Holder Part Number 1654010809-01 Footprint SIM_6P_5210622-SINR03 Description SIM card conn. 6p 2.54mm 90D(F) SMD 5210622-SINR Pin Pin Name C1 UIM_PWR C2 UIM_RESET C3 UIM_CLK C5 GND C6 UIM_VPP C7 UIM_DATA CN18 External USB Part Number 1654009513 Footprint USB_8P_UB1112C-8FDE-4F Description USB CONN. 8P 2.
CN19 External USB2.0+USB3.0 Part Number 1654010199 Footprint USB_13P_UEA1112C-UHS6-4F Description USB Conn. 2.0+3.
COM1/COM2 Part Number 1653004793 Footprint HD_10x2P_79_23N685B-20M10 Description BOX HEADER 10x2P 2.
CN21 COM3/COM4 Part Number 1653004793 Footprint HD_10x2P_79_23N685B-20M10 Description BOX HEADER 10x2P 2.
GbE Part Number 1652003274 Footprint RJ45_14P_RTA-195AAK1A Description PHONE JACK RJ45 28P DIP RTB-19GB9J1A Pin Pin Name 1 TX+(10/100),BI_DA+(GHz) 2 TX-(10/100),BI_DA-(GHz) 3 RX+(10/100),BI_DB+(GHz) 4 BI_DC+(GHz) 5 BI_DC-(GHz) 6 RX-(10/100),BI_DB-(GHz) 7 BI_DD+(GHz) 8 BI_DD-(GHz) CN27 Audio Part Number 1653004099 Footprint HD_5x2P_79_23N685B-10M10 Description BOX HEADER 5x2P 2.
CN29 MIOe Part Number 1654006235 Footprint MIOE_CPUSIDE Description B/B Conn. 40x2P 0.
CLK33M 43 NC 44 LPC_AD0 45 DDP_HPD 46 LPC_AD1 47 GND 48 LPC_AD2 Appendix A Pin Assignments 42 49 DDP_AUX+ 50 LPC_AD3 51 DDP_AUX- 52 LPC_DRQ#0 53 GND 54 LPC_SERIRQ 55 DDP_D0+ 56 LPC_FRAME# 57 DDP_D0- 58 GND 59 GND 60 USB0_D+ 61 DDP_D1+ 62 USB0_D- 63 DDP_D1- 64 GND 65 GND 66 USB1_D+/USB_SSTX+ 67 DDP_D2+ 68 USB1_D-/USB_SSTX- 69 DDP_D2- 70 GND 71 GND 72 USB2_D+/USB_SSRX+ 73 DDP_D3+ 74 USB2_D-/USB_SSRX- 75 DDP_D3- 76 GND 77 GND 78 USB_OC#
CN30 Inverter Power Part Number 1655000453 Footprint WHL5V-2M-24W1140 Description WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIH VEI Pin Pin Name 1 +12V 2 GND 3 ENABKL 4 VBR 5 +5V CN31 LVDS Part Number 1653920200 Footprint SPH20X2 Description B/B Conn. 40P 1.25mm 90D SMD DF13-40DP-1.25V(91) Pin Pin Name 1 +5V or +3.3V 2 +5V or +3.3V 3 GND 4 GND 5 +5V or +3.3V 6 +5V or +3.
GND 19 LVDS0_D2- 20 LVDS1_D2- 21 LVDS0_D2+ 22 LVDS1_D2+ 23 GND 24 GND 25 LVDS0_CLK- 26 LVDS1_CLK- 27 LVDS0_CLK+ 28 LVDS1_CLK+ 29 GND 30 GND 31 NC 32 NC 33 GND 34 GND 35 LVDS0_D3- 36 LVDS1_D3- 37 LVDS0_D3+ 38 LVDS1_D3+ 39 NC 40 NC Appendix A Pin Assignments 18 59 MIO-5251 User Manual
CN32 eDP Part Number 1653910261 Footprint SPH10X2 Description B/B Conn 10x2P 1.25mm 180D(M)SMD DF13-20DP-1.25V Pin Pin Name 1 GND 2 GND 3 D0- 4 D3- 5 D0+ 6 D3+ 7 GND 8 NC 9 D1- 10 GND 11 D1+ 12 AUX- 13 GND 14 AUX+ 15 D2- 16 GND 17 D2+ 18 Hot Plug Detect 19 +5V or +3.3V 20 +5V or +3.
SMBus/I2C Part Number 1655904020 Footprint FPC4V-125M Description WAFER 4P 1.25mm 180D(M) SMD 85205-04001 Pin Pin Name 1 GND 2 SMB_DAT 3 SMB_CLK 4 +5V CN34 Internal USB Part Number 1653003718 Footprint HD_5x2P_79_RA_N10_21N22050 Description PIN HEADER 5x2P 2.
FAN1 System Fan Part Number 1655003010 Footprint WHP3VA Description Wafer 2.
Appendix B B System Assignments This appendix contains information of a detailed nature.
B.1 System I/O Ports Table B.1: System I/O Ports Addr.
Table B.
MIO-5251 User Manual 66
Appendix C C EC Watchdog Timer Sample Code
C.1 EC Watchdog Timer sample code EC_Command_Port = 0x29Ah EC_Data_Port = 0x299h Write EC HW ram = 0x89 Watch dog event flag = 0x57 Watchdog reset delay time = 0x5E Reset event = 0x04 Start WDT function = 0x28 ==================================================== .model small .486p .stack 256 .data .code org 100h .STARTup mov dx, EC_Command_Port mov al,89h ; Write EC HW ram. out dx,al mov dx, EC_Data_Port mov al, 5Fh ; Watchdog reset delay time low byte (5Eh is high byte) index.
Appendix C EC Watchdog Timer Sample Code MIO-5251 User Manual 69
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
