MARS-1030 WinCE.
MARS-1030 User Manual ii
Contents Chapter 1 Introduction .......................................................1 1.1 About this Manual ........................................................................ 2 1.2 User and Product Safety ............................................................... 3 1.3 Federal Communication Commission Interference Statement ..... 5 1.4 Product Labeling........................................................................... 7 1.5 System Specifications.......................................
2.5.3 2.5.4 2.5.5 2.5.6 2.5.7 2.5.8 The Command Bar ................................................................. 42 The Task Bar .......................................................................... 43 The Soft Keypad ..................................................................... 43 Setting Up Wireless LAN RF ................................................. 44 Scanning Barcode ................................................................... 46 Help .....................................
3.2.21System .................................................................................. 114 3.2.22Volume & Sounds Properties ............................................... 116 3.3 Taskbar and Start Menu............................................................ 117 Chapter 4 Communication ..............................................119 4.1 Installing & Setting Up Microsoft ActiveSync ........................ 120 4.1.1 Installing Microsoft ActiveSync on the Host PC ................. 120 4.1.
A.2 Update Tab................................................................................ 158 A.3 Symbologies List ...................................................................... 160 A.3.1 Aztec ..................................................................................... 160 A.3.2 Codabar ................................................................................ 161 A.3.3 Code 11 ................................................................................. 162 A.3.4 Code 128 .
CHAPTER Introduction 1
Congratulations on purchasing the MARS-1030 Portable Data Terminal (PDT), a Microsoft Windows®CE .Net rugged PDT. Its special combination of features makes it perfect for using in a wide range of applications. These features as: • • • • • • • • • Intel® XScaleTM PXA255 400MHz 32 bits RISC Processor Windows® CE .NET 4.2 Operating System 64/128/256 MB SDRAM & 64/128 MB Flash ROM Open Architecture: User Accessible SD/CF/PCMCIA Slot 240 x 320, 3.
1.2 User and Product Safety • • • • Do not stare into the laser beam directly or shine it into eyes. Never use strong pressure onto the screen or subject it to severe impact, as the LCD panel could become cracked and possibility cause personal injury. If the LCD panel is broken, never touch the liquid inside, for such contact would irritate the skin.
– Do not expose battery pack to liquid, or allow the battery contacts to get wet. – Do not disassemble or modify the battery pack. The battery pack contains safety and protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite. – Do not discharge the battery pack using any device except for the specified device. When it is used in devices other than the specified devices, the battery pack can be damaged or its life expectancy reduced.
1.3 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Caution: SCC declares that MARS-1030 ID:M82-MARS-1030 is limited in CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A. The FCC ID of MARS-1030 is M82-MARS-1030 IMPORTANT FOR LASER PRODUCTS 1. 2. 3. Class II Laser Product Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
1.4 Product Labeling The PDT has several labels as showed in Figure 1-1 and 1-2. Figure 1.
Figure 1.
1.5 System Specifications The MARS-1030 PDT detailed specifications as follows. Unless otherwise noted, all the specifications are subject to change without prior notification. Table 1.1: System Specification MARS-1030 Processor Memory Display Audio Radio Support - Communication Ports Scan Engine (Optional) Expansion Slot - LED Power System - 400MHz Intel PXA255 32 bits RISC CPU 64 or 128MB Flash ROM 64,128 or 256MB SDRAM 240 x 320 3.5” TFT 256K Color LCD with LED backlight One mono speaker 2.
- Power button 4-way navigation button 4 Application Keys Button/Key 3 Scanner Enable Keys SW Reset input button 16 Alpha-numeric keyboard Dimensions: 192.5mm (L) x 91.3mm / 78mm(W) x 42.2mm / 60.6mm (H) Dimensions and Weight - Weight: 560g with Standard Battery Pack 500g without Battery Pack Color - Black - Standard Packing list: 1. MARS-1030 Terminal 2. Stylus 3. USB Client Cable for Terminal 4. Earphone/ Microphone Set 5. Standard AC Adapter 5VDC/2.6A 6. AC Power Cord 7. Standard Battery Pack (3.
1.6 Environment Standard Table 1.2: Environment Standard Operating Temperature 14oF ~ 122oF( -10oC ~ 50oC) Storage Temperature -4oF ~ 158oF (-20oC ~ 70oC) 5% ~ 80% (non-condensing) 5ft (1.
1.7 Warranty and after service Should this PDT be malfunctioned, please contact your original retailer providing information about the product name, the serial number, and the details about the problem. Use this table and the MAN paragraph formats to tag body content.
CHAPTER Getting Started 2
2.1 Check the package Open the package and check all the parts are inside without shortage and damage: Figure 2.1: Inside the package 1. 2. 3. 4. 5. 6. 7. 8. 9. MARS-1030 Terminal Stylus USB Client Cable for Terminal Earphone/ Microphone Set Standard AC Adapter 5VDC/2.6A AC Power Cord Standard Battery Pack (3.
2.2 General View of the PDT 2.2.1 PDT front side view Figure 2.2: PDT Front side view 2.2.2 PDT back side view Figure 2.
Table 2.
2.3 Charging the Battery Pack Before using the PDT, perform the basic procedure of charging the battery pack through the following steps. 2.3.1 1. Installing the battery pack On the PDT attached with a hand-strap, detach and loose the handstrap. Figure 2.
2. Turn the locking screws (right and left) downwards and lift the battery cover away from the PDT. Figure 2.
3. Insert the battery pack into the battery compartment with the label facing out, and ensuring the battery snaps into place. Figure 2.
4. Replace the battery cover by inserting the top first, and then press the bottom in firmly. Turn the locking screws (right and left) upwards to secure the cover to the PDT. Figure 2.7: Replace the battery cover 5. Charge time. For the first time to charge the battery pack needs approximately 6 hours. Subsequent charging time needs approximately 4 hours. • When charging the battery pack, the charge LED indicator on the PDT turns on Red.
2.3.2 1. 2. 3. Charging the battery pack with Power Adapter Connect the Power cord to the Power adapter. Plug in the connector of the power adapter. Connect the power cord to a power source. Figure 2.8: Charging with power adapter • • When charging the battery pack, the charge LED indicator on the PDT turns on Red. After the battery pack is fully charged, the charge LED indicator turns to Green.
2.3.3 Charging the battery pack with Single Dock a) Leave the battery pack inside of the PDT 1. 2. 3. 4. Connect the Power cord to the Power adapter Connect the power cord to a power source Plug in the connector of the power adapter with Single Dock Insert the PDT into the Single Dock Figure 2.9: Charging with Single Dock • When charging the battery pack, the charge LED indicator on the PDT turns on Red. After the battery pack is fully charged, the charge LED indicator turns to Green.
b) Place the spare battery pack into the Single Cradle’s spare Battery charging slot 1. 2. 3. 4. Connect the power cord to the power adapter Connect the power cord to a power source Plug in the connector of the power adapter with Single Cradle Insert the Battery pack into the Single Cradle’s spare Battery slot. • When charging the Battery pack in the Single Cradle’s spare Battery slot, the Single Cradle charging LED will turn on Red. After the Battery pack is fully charged, this LED will turn to Green.
2.4 Handling the PDT 2.4.1 Starting the PDT Press the Power key to turn on/off the PDT. If the PDT does not power on, perform a cold boot. See 2-7 Resetting on page 2-27. CAUTION: When a battery is fully inserted in PDT for the first time, upon the PDT’s first power up, the device boots and powers on automatically. When the PDT is powered on for the first time, it initializes its system. A splash screen (figure 2-10) appears for a short period of time followed by the Wince.NET 4.2 window. Figure 2.
2.4.2 • Power on / off To turn on the PDT Press the Power key briefly ( ). If the PDT does not power on, perform the cold reset. See chapter 2.7.1. As the PDT initializes its file system, it splash screen displays for about 30 seconds followed by calibration screen. Every time you perform a cold reset, these screens will also appear. To turn off the PDT, just press the Power key again. This action does not actually turn off the PDT, it only turns the PDT into suspend mode.
2.4.4 Adjusting the brightness The factory default for the brightness is in Middle level. You can adjust the brightness to meet your environment and comfort as: key and then press on the right key 1) Become brighter: Press the of Navigation key . key and then press on the left key of 2) Become darker: Press the Navigation key . 3) The display will become dimmer automatically, if you do not perform any operation for a specific period of time. This will help to save the battery power.
2.4.7 Using the Keypad Figure 2.
Table 2.2: Table 2-2 Keypad List Key Fn + Main Function Main Function Alpha + Main Function None.
Key Fn + Main Function Main Function Alpha + Main Function Function change 1 (at) 2 ’ 3 (Plus Sign) 4 Paste 5 Del (Delete) 6 (Minus Sign) 7 Copy 8 (AND) 9 (Asterisk) 0 Space . (Point) Start Menu Enter (Backslash) Table 2.3: Special Assembler Key Assembler Key Functionality Definition Warm Reset Press “F1” and “F4” button simultaneously. Cold Reset Press “Power”, “F1” and “F4” button simultaneously.
Table 2.4: Definition of main Function Key Main Function Definition None. Keep its function or by customer demand. Main BarCode Scan The key activates the Key scan function of MARS-1030. Power On/Off The key puts the terminal into and wakes the terminal from suspend mode. Internet Explorer Application key 1, User can define F1 function from setting. Microsoft WordPad Application key 2, User can define F2 function from setting. Inbox Application key 3, User can define F3 function from setting.
Key Main Function Definition Backspace “Backspace” key, it moves the cursor back one space each time the key is pressed. It deletes the previous character each time it is pressed if you are typing text. The cursor will move continuously if button is pressed continuously. 1. The Change to letters key enables you to toggle between the numeric and alpha modes. Numeric mode is when you type numbers with number keys. Alpha mode is when you type letters with the number keys. 2.
Key Main Function Definition 8 Number key “8” 9 Number key “9” 0 Number key “0” .
2.4.7.1 Special Function by “Fn” + main Function The “Fn” key is used in combination with other keys to type special characters and perform system functions. Table 2.5: Special Function key define Key Sequence Fn + Main Function Definition Increase the LED backlight brightness of display screen(Lighter) Backlight Increase You must press key, then press key to increase backlight brightness each time.
Key Sequence Fn + Main Function Definition The “TAB” function is to move the cursor to the next tab stop or the next control (on a form) TAB (Tabulation) To do this function by pressing @ (at) key first, and then pressing each time. key Enter an {@, at} by pressing key, then pressing key. Enter a {’} by pressing ’ pressing (Plus Sign) key, then key. Enter a plus sign by pressing then pressing key, key It is to do “Paste” function.
Key Sequence Fn + Main Function Definition Enter an AND sign by pressing (AND) key, then pressing key. Enter an asterisk sign by pressing (Asterisk) key first, and then pressing key. The “Space” function is to move the cursor one space. Space To do this function by pressing key first, and then pressing each time. It displays the Start menu. Start Menu key To do this function by pressing key first, and then pressing each time.
2.4.7.2 Alpha plane keys by “Alpha” + main Function 1. The key enables you to toggle between the numeric and alpha modes. Numeric mode is when you type numbers with number keys. Alpha mode is when you type letters with the number keys. 2. When you press key, it appears “Alpha” icon at the Task bar to indicate Alpha mode is enabled. It means Alpha mode is disabled if there isn’t “Alpha” icon at Task bar. The keypad stays in the alpha mode until you press key again.
To enter Press the Keys To enter b B c C d D e E f F g G h H i I j J k K l L m M 37 Press the Keys Chapter 2
To enter Press the Keys To enter n N o O p P q Q r R s S t T u U v V w W x X MARS-1030 User Manual 38 Press the Keys
To enter Press the Keys To enter y Y z Z [ ] , ; = % Press the Keys Note: 1. The key is not needed to key in if the character isn’t the first alpha character being keyed in. 2. The keys are not needed to key in if it is not the first capital alpha character being keyed in.
2.4.8 Using the Ear/Microphone Connect Ear/Microphone to PDT earphone jack connector. The PDT is not built in microphone; if you like to record the voice, you have to use Ear/Microphone. Figure 2.
2.5 Navigating the Display 2.5.1 Setting Time and Date In the Date/Time options, you can change the year, month, date, time, time zone, or select automatic adjust for Daylight Saving Time. To set or change the date and time: Figure 2.14: Date/Time properties 1. 2. 3. 4. 5. 6. 7. Select Start > Settings > Control Panel > Date/Time To change the year, select the year or open a numeric dial. Select the up arrow to increase the value; select the down arrow to decrease the value.
2.5.2 Entering the Data To select and open programs, select Start > Programs from the task bar to open a list of available programs. Or if the program has a icon on the desktop, double-tap to open it. There are several ways to enter data on the PDT once in an application: • • • • • Use the keypad to enter alpha-numeric characters, Refer to “2.4.7 Using the keypad” on page 2-11. Use the stylus on the touch screen on page 2-11 for more information on using .the stylus.
2.5.4 The Task Bar The Task bar at the bottom of the screen displays the icon, an icon for the active program, the current time, and system icons for utilities loaded in memory. The Task bar includes menu names, buttons, and the keyboard icon, which opens and closes the soft input panel (SIP). The Task bar allows you to select and close programs. Refer to Figure 2-15 to view the Task bar. Command Bar Task Bar Figure 2.15: Task Bar & Command Bar 2.5.
2.5.6 Setting Up Wireless LAN RF 1) Press “Start”---“Setting”---“Control Panel” --- “WLAN Manager”. 2) Launch the WLAN Manager to Enable WLAN device. 3) Into AP Browser tab, tap Scan button to renew the network. 4) Select a network, tap the Join button or double tap it for more options. 5) Press OK to save all your Wireless LAN settings. 6) Tap the “Exit” button to Disable WLAN device. Figure 2.16: WLAN Manager MARS-1030 User Manual Figure 2.
Note: 802.11b WLAN is not connecting to network. 802.11b WLAN is no signal. 802.11b WLAN signal is Low. 802.11b WLAN signal is In General. 802.11b WLAN signal is Good. Figure 2.18: WLAN Manager Figure 2.
2.5.7 Scanning Barcode To use the scanning function, complete the following steps: 1. 2. 3. 4. 5. 6. 7. If you have not already done so, remove the protective plastic film before using devices equipped with a laser scanner. Select Start > Setting > Control Panel > Barcode Setting; complete all configurations following all description of 3.2.1 BarCode Setting. Run the WordPad software program Aim the scanning beam at the center of bar code.
– The reader can be detected by a red beam. 8. Bad Scanning Position – Make sure that the bars enter the laser beam when scanning large barcodes. – Scanning operations may fail if the laser beam positions as below. Note: this product scans using laser light. Never look directly into the laser light or shine the laser light into the eyes. 2.5.8 Help To tap “?” can get help information for each program.
2.6 Power management 2.6.1 Suspend Mode The PDT will go into a suspend mode when it is idle for a period of time. The idle duration can be customized using the Power control panel (refer to Figure “Schemes Tab”) Suspend mode works and looks just like you have turned the unit off. Press the key to suspend the PDT, Press the key again for the PDT to resume its Previous state. Use the Battery power control panel to set the duration to switch state to Suspend mode when system using battery power.
Suspending: The following conditions will suspend: • • • • Press key while the unit is on. The duration timer of item “Switch state to Suspend” expires, which indicates that there has been no use for a specified of time. The battery pack is completely discharged. Tap Start > Suspend Tap here to let PDT enter into suspend mode 2.6.2 Resuming Use one of following methods to resume (wake up the PDT): • • Press key to suspend or resume (wake up). Put the PDT into a dock.
2.7 Resetting the PDT 2.7.1 Software (Warm) Reset A warm reset is a transition from the on, idle, or suspend power state that close all applications, clears the working RAM, but preserves the file system. Reason to Warm Reset: If an application “hangs”, initiate a warm reset to terminate the application only. Process to Warm Reset: To a warm reset, press “F1” and “F4” button simultaneously. After Warm Reset: • • The desktop appears with the application shortcuts on the screen.
CHAPTER Setting 3
3.1 Introduction To view available options for PDT’s setting, tap Start > Settings. Then, there are three items inside Settings: “Control Panel”, “Network and Dial-up” and “Taskbar and Start”. 3.2 Control Panel To view the Control Panel and settings you can modify by tapping Start > Settings > Control Panel. Figure 3.
3.2.1 BarCode Setting CAUTIONPlease do not enter into any Barcode Application Program before settings completing this Barcode. There are three Tabs for scanner configuration setting: “Basic” Tab, “Code Configure” Tab and “Code ID” Tab. In addition, there is “BarCode Setup” for the “Code Configure” Tab.
3.2.1.1 “Basic” Tab Figure 3.
Table 3.1: Basic Explaining Field Name Beep After Scan OK Scan Timeout (sec) Termination Code Continuous Scan Keybd Message Function Explaining Select the numbers of beep tone after scan OK. After scanning the barcode, do None not give out beep sound. After scanning the barcode, One Time give out beep one time. After scanning the barcode, Two Times give out beep two times. Select the scanning timeout duration (in seconds) from this pull-down list.
3.2.1.2 “BarCode” Tab: Select the barcode symbologies you plan to scan from the list. Tap to enable/disable the desired symbologies. Figure 3.3: Code Configure Tab Table 3.2: Code Configure Explaining Barcode Symbology Explaining Type A. Numeric-only Barcodes UPC-E UPC-A EAN-13 / ISBN MARS-1030 User Manual Compressed version of UPC code for use on small products. Universal product code seen on almost all retail products in the USA and Canada.
Barcode Symbology EAN-8 / JAN-8 UPC-EAN Add-ON 2/5 Industrial 2 of 5 / IATA Interleaved 2 of 5 Plessey / MSI Code 11 Codabar / NW 7 Matrix 2 of 5 Explaining Compressed version of EAN code for use on small products. UPC-A, UPC-E, EAN-13, and EAN-8 may all include an additional barcode to the right of the main barcode. This second barcode, which is usually not as tall as the primary barcode, is used to encode additional information for newspapers, books, and other periodicals.
Barcode Symbology Explaining GTIN Global Trade Identification Number Korea Code 3 of 5 --- RSS Reduced Space Symbology MARS-1030 User Manual 58
3.2.1.3 “Code ID” Tab: Figure 3.4: Code ID Tab Table 3.3: Code ID Explaining Code ID is added into prefix of the barcode and let user identify which kind of barcode being scanned. Enable this functionality. Enable Code ID Set 1 ~ Set 5 User Define Barcode List Default 59 Select one default value by Set 1 ~ Set 5. (See the “Table 3-4 Code ID Set1-Set5 Table”) Establish number by oneself. Set 1 ~ Set 5: defaults setting. User Define: select barcode to define.
Table 3.
3.2.1.4 BarCode Setup A. First select barcode type then select barcode to setting. B. Press “Default” button to reset all configuration setting of this barcode into default values. C. Press “Apply” button to be decided setting of this barcode. Please see 3.2.2 Symbologies List for more detail information of each Barcode. Figure 3.
3.2.2 Symbologies List A Type -- Numeric-only Barcodes 3.2.2.1 UPC-E Figure 3.6: UPC-E Table 3.5: UPC-E Explaining Item Explaining Format Ignore 1st digit Transmit 1st digit Send Check Digit MARS-1030 User Manual Do not transmit 1st digit by barcode. Transmit 1st digit by barcode. Whether send check digit by barcode.
3.2.2.2 UPC-A UPC-A movements together with EAN-13, so only Enable EAN-13 then UPC-A will be Enable, too. Figure 3.7: UPC-A Table 3.6: UPC-A Explaining Item Explaining Format Ignore 1st & 2nd digits Transmit 1st digit Transmit 2nd digit Transmit 1st & 2nd digits Send Check Digit 63 Do not transmit 1st digit by barcode. Transmit 1st digit by barcode. Transmit 2nd digit by barcode. Transmit 1st & 2nd digits by barcode. Whether send check digit by barcode.
3.2.2.3 EAN-13 / ISBN Figure 3.8: EAN-13 / ISBN Table 3.7: EAN-13 / ISBN Explaining Item Explaining Send Check Digit Do not transmit 1st digit by barcode. Transmit 1st digit by barcode. Transmit 2nd digit by barcode. Transmit 1st & 2nd digits by barcode. Whether send check digit by barcode. Enable ISBN Code Whether use this ISBN Code.
3.2.2.4 EAN-8/JAN-8 Figure 3.9: EAN-8/JAN-8 Table 3.8: EAN-8/JAN-8 Explaining Item Explaining Format Ignore 1st digit Transmit 1st digit Send Check Digit Convert to EAN-13 Add five 0 Do not transmit 1st digit by barcode. Transmit 1st digit by barcode. Whether send check digit by barcode. When this option is selected the scanner will convert UPC-E to UPC-A by transmitting five zeroes … Ahead of Add five zeroes at prefix of the barcode. code After 3 digits Add five zeroes from 4th digits.
3.2.2.5 UPC-EAN Add on 2/5 • UPC-E, UPC-A, EAN-13 / ISBN and EAN-8 / JAN-8 may all include an additional barcode to the right of the main barcode. • This barcode will show primary & additional code together. • So the UPC-EAN Add-ON 2/5 code is unable to use alone, must operate in UPC-E or UPC-A or EAN-13 / ISBN or EAN-8 / JAN-8. Figure 3.10: UPC-EAN Add on 2/5 UPC-EAN Add-On 2/5 Explaining Item 2/5 Explaining Only read the code with Addon Only reads the codes that have addenda.
3.2.2.6 Industrial 2 of 5 / IATA Figure 3.11: Industrial 2 of 5 / IATA Table 3.9: Industrial 2 of 5 / IATA Explaining Item Explaining Send Check Digit Whether send check digit by barcode. Enable IATA Code Whether use this IATA Code. Checksum Whether verify checksum by barcode.
3.2.2.7 Interleaved 2 of 5 Figure 3.12: Interleaved 2 of 5 Table 3.10: Interleaved 2 of 5 Explaining Item Explaining Whether send check digit by Send Check Digit barcode. Whether verify checksum by Checksum Verify barcode.
3.2.2.8 Plessey / MSI Figure 3.13: Plessey / MSI Table 3.11: Plessey / MSI Explaining Item Explaining Format Mode 10 Mode 10-10 Mode 11-10 Send Check Digit 1 Digit 2 Digits Checksum mode for this barcode. Whether send check digit by barcode. Check 1 digit & send by checksum. Check 2 digits & send by checksum.
3.2.2.9 Code11 Figure 3.14: Code 11 Table 3.12: Code 11 Explaining Item Explaining Send Check Digit 1 Digit 2 Digits MARS-1030 User Manual Whether send check digit by barcode. Check 1 digit & send by checksum. Check 2 digits & send by checksum.
3.2.2.10 Codabar / NW7 Figure 3.15: Codabar / NW7 Table 3.13: Codabar / NW7 Explaining Item Explaining Start / Stop Digit ABCD abcd TN*E tn*e Checksum Verify Whether transmit Start & Stop Digit. Start / Stop transmit type Whether verify checksum by barcode.
3.2.2.11 Matrix 2 of 5 Figure 3.16: Matrix 2 of 5 Table 3.14: Matrix 2 of 5 Explaining Item Send Check Digit Checksum Verify Min-Max (Default: 4 / 48) Length Fixed MARS-1030 User Manual 72 Explaining Whether send check digit by barcode. Whether verify checksum by barcode.
B Type -- Alphanumeric Barcodes 3.2.2.12 Code39 / Code32 Figure 3.17: Code39 / Code32 Table 3.15: Code39 / Code32 Explaining Item Explaining Format Code39 Standard Code39 Full ASCII Code32 Start / Stop Digit Enable Code 39 Standard characters Enable Code 39 Full ASCII character Enable Code 32 Whether transmit Start & Stop Digit. Verify Whether verify checksum by barcode. Transmit Whether transmit checksum by barcode.
3.2.2.13 Code93 The barcode do not have setting. Figure 3.
3.2.2.14 Code128 / UCC EAN128 Figure 3.19: Code 128 / UCC EAN128 Code128 / UCC EAN128 Explaining Item Explaining Enable UCC128/EAN128.
C Type -- Others Barcodes 3.2.2.15 China Post Figure 3.20: China Post Table 3.16: China Post Explaining Item Explaining Checksum Verify Send Check Digit Min-Max (Default: 4 / 48) Length Fixed MARS-1030 User Manual Whether verify checksum by barcode. Whether send check digit by barcode.
3.2.2.16 Code4 The barcode do not have setting. Figure 3.
3.2.2.17 GTIN The barcode do not have setting. Figure 3.
3.2.2.18 Korea Code 3 of 5 The barcode do not have setting. Figure 3.
3.2.2.19 RSS Figure 3.24: RSS RSS Explaining Item Explaining Convert to UCC128 Checksum MARS-1030 User Manual Verify The scanner will convert RSS to UCC128. Whether verify checksum by barcode.
3.2.3 Bluetooth Device Properties Table 3.17: Bluetooth Device Properties ICON ITEM & FUNCTION • “Scan Device” Tab ( Figure 3-25) : * Tap the Scan Device button to initiate a scan for Bluetooth hardware. The Bluetooth manager lists the Bluetooth devices that it finds, see Figure 3-26. If Bluetoothhardware is not found the Bluetooth Hardware Error window appears, see Figure 3-27. Table 3-18 described the Bluetooth Icons. * Double tap the device to connect to on the device list.
Figure 3.27: Bluetooth Error Windows Figure 3.28: Bluetooth Manager Windows Figure 3.29: Bluetooth Enter PIN Windows Figure 3.30: Bluetooth Manager Windows Note: If the device to which the mobile computer is bonding does not appear in the list, ensure it is turned on, in discoverable mode, and within range (30 feet / 10 meters) of the mobile computer.
Table 3.18: Bluetooth Icon Icon Description Unknown device icon Locked icon Not locked icon Device is not defined Device is locked and cannot be bonded to. Device is not locked and can be bonded to. Bluetooth device icon Bluetooth device Bonded device icon Bonded Bluetooth device Mobile device icon Device is a mobile device Phone icon Device is a phone. Printer icon Device is a printer Network icon Device is a network. Linked icon Device is linked.
3.2.4 Certificates Certificates are used by some applications for establishing trust and for secure communications. Certificates are signed and issued by certificate authorities and are valid for a prescribed period of time. Windows CE manages multiple certificate stores. Table 3.19: Certificates ICON ITEM & FUNCTION • “Store” Tab ( Figure 3-31) : * In the Stores tab, select the certificate store you wish to view or modify from the drop-down list (Figure 3-32).
Figure 3.31: Certificates Figure 3.32: Certificates Figure 3.33: Certificates Figure 3.34: Certificates Figure 3.
3.2.5 Control Center The Control Center includes four AP, listed the following ...... Figure 3.36: Control Center 3.2.5.1 Information Table 3.20: Information ICON ITEM & FUNCTION • “Information” Tab : * Provide Software version, MAC address, Bluetooth ID, Serial No. and Configuration No.
3.2.5.2 Brightness Table 3.21: Brightness ICON ITEM & FUNCTION LCD Brightness Tune the LCD brightness by tapping right-arrow & left-arrow. Can also tune the LCD brightness by pressing right-direction key or left-direction key of keypad. Amounts 7 steps: Every step have corresponding picture of self. 1. 2. 6. 7. 3. Enable Keypad Brightness 4. 5. Open keypad brightness or not. Backlight Timeout Save battery life by automatically turning off the backlight when not used.
Figure 3.37: Brightness 3.2.5.3 Backup Restore Table 3.22: Backup Restore ICON ITEM & FUNCTION 1. You can backup/restore system to/from flash disk or inserted memory card. (A. Disk on Chip, B. CF Card, C. SD Card) ( Figure 3-38) 2. When you launch this AP, it must check backup file in DOC first. And if you select other storage, it will check again. 3. Then if it has the file, appeared its date behind “Last backup date:”; if not, disable “Restore Now” Button. 4.
Figure 3.38: Backup Restore Figure 3.40: Backup OK Figure 3.39: Backup & Restore Start Figure 3.
3.2.5.4 Fn-key Settings Table 3.23: Fn-Key ICON ITEM & FUNCTION Fn-Key Setting (Figure 3-42) Fn Key The Application Program of default setting F1 Internet Explorer F2 Microsoft WordPad F3 Inbox F4 My Computer * To assign your favorite application program to F1, F2, F3 and F4 hot keys. * Choose one of F1, F2, F3 and F4 from pull-down list. (Figure 3-43) * To tap “Browse…” inside “Assign program” applet. * Select one application program you want from program list, then, choose “OK”.
3.2.6 Date/Time Table 3.24: Date/Time ICON ITEM & FUNCTION • “Date/Time” Tab :( Figure 2-14) * Please see the detail information of 2.5.1 Setting Time and Date on P.2-21 3.2.7 Dialing Properties Table 3.25: Dialing properties ICON ITEM & FUNCTION • “Dialing Properties” Tab :( Figure 3-44) * In the When dialing from list, select the “Location” where you want to change settings.(Figure 3-45) * To create a new location, select “New”. Enter the name of the location, and then select “OK”.
Figure 3.44: Dialing Properties Figure 3.45: Dialing Properties Figure 3.46: Dialing Properties Figure 3.
3.2.8 Display Properties Table 3.26: Display properties ICON ITEM & FUNCTION • “Background” Tab :( Figure 3-48) * From the “Image” list, select an image you want as the background of the desktop.(Figure 3-49) * To locate an image in another folder, select “Browse”. * (Figure 3-50) * To have the image cover the entire background, select “ Tile image on background” • “Appearance” Tab(Figure 3-51) * Change the color scheme :( Figure 3-52) - From the” Scheme” list, select a scheme.
Figure 3.50: Display properties Figure 3.51: Display properties Figure 3.
3.2.9 Input Panel Table 3.27: Display properties ICON ITEM & FUNCTION • “Input panel” Tab :( Figure 3-53) * Select the input method you want to change. * To change the Soft Keyboard Options , tap “Option” (Figure 3-54) . • “Options” Tab : * Change the soft keyboard options as desired, selecting from: - Large or small keys - Using gestures for space, black-space shift, and enter. * To exit the soft keyboard Options, press “OK” on the control bar, or press the key on the keypad.
3.2.10 Internet Options Table 3.28: Internet Options ICON ITEM & FUNCTION • “General” Tab :( Figure 3-55) * Type in the URL of desired start page and the desired search engine. You also change the Cache Size, clear the Cache and Clear the History.. • “Connection” Tab :( Figure 3-56) * Modify the network access setting as desired. • “Security” Tab (Figure 3-57) * Modify the security settings as desired. You can enable any of the following by tapping the checkbox: - Allow cookies - Allow TLS 1.
Figure 3.55: Internet Settings Figure 3.56: Internet Settings Figure 3.57: Internet Settings Figure 3.
3.2.11 Keyboard Table 3.29: Keyboard ICON ITEM & FUNCTION • “Repeat” Tab :( Figure 3-59) * To change the amount of time between depressions before repetition starts, adjust the Repeat delay slider * To change the repeat rate, adjust the Repeat rate slider. * Test your new setting. * Tap “ OK” to exit the “Keyboard” Tab. Figure 3.
3.2.12 Network and Dial-up Connections Table 3.30: Network and Dial-up Connections ICON ITEM & FUNCTION • “Connection” Tab : * To create a “Dial-up Connection”: - Double-tap the “Make New connection”. - In the “Make New Connection” dialog box, enter a name for the connection. - Select “Dial-Up Connection”. - Select the “Next” button. - Select the modem you want use. - Select “Configure” - Under “Connection Reference”, use the default settings provided.
ICON ITEM & FUNCTION Once you have established an account, create a new connection on your device. When creating this connection, you should be able to use all of the default TCP/IP settings provided in the Make New Connection Wizard. If you can’t connect using the default settings, contact your ISP or access your ISP’s Web site for specific TCP/IP information as well as primary and secondary DNS address.
Figure 3.62: Network and Dial-up Figure 3.63: Network and Dial-up Connections Connections Figure 3.64: Network and Dial-up Figure 3.
Figure 3.66: Network and Dial-up Figure 3.67: Network and Dial-up Connections Connections Figure 3.68: Network and Dial-up Figure 3.
Figure 3.70: FNetwork and Dial-up Connections Figure 3.
3.2.13 Owner Table 3.31: Owner ICON ITEM & FUNCTION • “Identification” Tab : (Figure 3-74) * Fill in or edit the data as desired. * To have this information displayed when you start your device, select “Display Owner Identification” at Power On. * To set up identification for remote networks, see Setting up identification for remote networks. • “Network ID” Tab: (Figure 3-75) * Enter the user name, password, and domain name you use to log on to remote network. Figure 3.
3.2.14 Password Table 3.32: Password ICON ITEM & FUNCTION • “Password Setting” Tab : (Figure 3-76) * Enter the password * In the “Confirm password “box, enter the password again. * To require the password on startup, select “Enable password protection at power- on“. and/or select “Enable password protection for screen saver” * To exit the Password control panel, press “OK” from the control bar, or press the key on the keypad. Figure 3.
3.2.15 PC Connection Table 3.33: PC Connection ICON ITEM & FUNCTION • “PC Connection” Tab : (Figure 3-77) * Select the first checkbox to enable direct connections to the desktop computer. (Figure 3-77) * Tap the “Change Connection…” button to modify the connection method from USB or Serial. (Figure 3-78) * To exit the “Change Connection” dialog, press “OK” from the control bar, or press the key on the keypad.
3.2.16 Power Table 3.34: Power ICON ITEM & FUNCTION • “Battery” Tab : (Figure 3-79) * Provide change level indicators for Main battery and Backup battery. * Provide remaining power capacity of main battery. * If a “Main Batteries very Low” warning message shows, the remaining battery life is around 30 minutes to MARS-1030 shuts down.
Figure 3.77: Power Figure 3.78: Power Figure 3.79: Power Figure 3.80: Power Figure 3.
3.2.17 Regional Settings Table 3.35: Regional Settings ICON ITEM & FUNCTION • “Region” Tab : (Figure 3-84) * Select the desired location/language. * Review the Appearance samples in the bottom half of the screen. * Select the Tab at the top for any settings you wish to change, Options to modify include Number, Currency, Time, and Date. Figure 3.
3.2.18 Remove Programs Table 3.36: Remove Programs ICON ITEM & FUNCTION • “Remove Programs” Tab : * Only user installed programs can be removed. - Select the program you wish to remove from the list and press “remove” button.
3.2.19 Storage Manager Table 3.37: Storage Manager ICON ITEM & FUNCTION • “Storage Manager” Tab : (Figure 3-83) * To change Storage properties control panel default settings: Insert. Compact Flash(CF) or Secure digital (SD) storage card into the unit. - Select Start > Settings > Control Panel > Storage Properties - From the “Storage Info” pull-down list, select the desired storage device. - You can also format, dismount, and create partitions on storage devices using this control panel.
3.2.20 Stylus Table 3.38: Stylus ICON ITEM & FUNCTION • “Double-Tap” Tab : (Figure 3-86,Figure 3-87) * Double-tap the checkerboard grip at a comfortable speed. * Double-tap clapboard to test your settings * The function is OK if the figures are changed from Figure 3-86 to Figure 3-87. * To tap “OK” to exit the Stylus Properties.
Figure 3.86: Stylus Properties 113 Figure 3.
3.2.21 System Table 3.39: System ICON ITEM & FUNCTION • “General” Tab : (Figure 3-90) * To show: - Firmware information - Information about Processor type, Memory size, Expansion card • “Memory”: (Figure 3-91) * Move the slider to adjust memory allocation. Default storage memory is normally is normally set to about 8MB with the reminder assigned to Program memory. * Press the “OK” key on the Keypad.
Figure 3.88: System Properties Figure 3.89: System Properties Figure 3.90: System Properties Figure 3.
3.2.22 Volume & Sounds Properties Table 3.40: Volume & Sound ICON ITEM & FUNCTION • “Volume” Tab : (Figure 3-94) * The factory default for Volume is the forth level. You can adjust the volume to your environment and comfort. - Set the volume by adjusting the slider from Soft to Loud, or press Right or Left edge of Navigation keys • “Sounds ” Tab: (Figure3-95) * Enable the desired sounds for key clicks, screen taps, notifications, and applications. Figure 3.
3.3 Taskbar and Start Menu Table 3.41: Taskbar and Start menu ICON Taskbar and Start Menu ITEM & FUNCTION • “General” Tab : * In this tab, You can change the position of the Taskbar and Start menu - Is always on top or not - Auto hide or not - Show Clock or not • “Advanced ” Tab: * Tap the “Clear” button to remove the contents of the Documents Menu. * Enable “ Expand Control Panel” to list all icons of Control Panel from top to bottom.
MARS-1030 User Manual 118
CHAPTER Communication 4
4.1 Installing & Setting Up Microsoft ActiveSync 4.1.1 Installing Microsoft ActiveSync on the Host PC Microsoft ActiveSync is a file transfer tool to synchronize the files on a PC with the files on your PDT. To install Microsoft ActiveSync, complete the following steps on the PC: 1. 2. 3. 4. 5. 4.1.2 1. • • 2. 3. Go to the Microsoft Windows CE.NET website and download the latest current version of ActiveSync: http://www.microsoft.com/mobile/pockeypc/downloads/ .
4.2 Using ActiveSync Use ActiveSync to transfer and synchronize files between the PDT and the Host PC. 4.2.1 Setting up a Partnership During the Microsoft ActiveSync installation, you were prompted to create a partnership with your mobile device. When you set up a partnership, you select synchronization and file conversation settings, which are contained in a file on your desktop computer. This file enables your desktop computer to recognize your device.
4.2.2 ActiveSync File Synchronization ActiveSync files synchronization requires an ActiveSync partnership between the PDT and the Host PC. Refer to “Setting up a Partnership”, above: • • • Select the files in the synchronization configuration for the PDT partnership. Select Tools > Options from the ActiveSync command bar to configure the synchronization options. Place the file to be synchronized in the Synchronization folder created you’re My Documents directory. Defaults to the desktop.
CHAPTER 5 Software Applications
5.1 Introduction The PDT includes Calculator, Inbox,….. You can switch to any software program by tapping the Start Menu. 5.2 Software Applications 5.2.1 Calculator It can process the basic numeric calculation with “+”, “-“ “*” and “/“. * * 5.2.
* * * * * Select Service> Options from the command bar. Drag the dialog to show the right edge to configure e-mail. Select “Add…” (Note 1) In the “Service Type” list, select POP3 Mail or IMAP4 Mail. (POP3 is the most common mail protocol for ISPs).Enter a unique name for e-mail service in the “Service name” field. This name cannot be changed later. Select “OK”. The Mail Service Setup wizard appears after you add a service.
* * on the service you are using. If this is not your e-mail address, enter the correct address in the box. Set general preferences: If you are adjusting the setting of an existing service, select Service> Options, select the service you are using, select Properties, and then select Next.
– Only synchronize folder hierarchy under Inbox (IMAP4 only): Select to speed download time by preventing the complete downloaded of the folder list every time you connect. – Get meeting requests (POP3 only): Select to download and store copies of meeting requests when getting full copies of messages.
– Select Services> Options > Read tab. – Select desired options. Delete a message: Select the message and select File> Delete. Messages are moved to Deleted (local) folder and deleted according to the option you have selected in Services> Options> Delete tab: – On connect/disconnect: Deletes messages when you connect or disconnect from your mail service or exit Inbox. – Immediately: Deletes messages as soon as you select File> Delete.
• • • Delete a folder: – Select the folder you want to delete – Select File> Delete Designate a folder as offline: Only IMAP4 folders can be designated as offline. All IMAP4 default folders, such as Inbox, are automatically designated as offline. Messages in offline folders can be viewed when you are disconnected from your mail server. If a folder is not designated as offline, you will be able to read and respond to messages in that folder only when connected to the server.
Check Name. If there is only one match, the e-mail address is inserted. If there is more than one match, select the correct address from the Choose E-mail Recipients dialog box. If there is no match then add a new e-mail address through Choose E-mail Recipients. – To attach a file, select File> attachments> Add Attachment. – Select File> Send. If you are working offline, the message is moved to the Outbox folder and will be sent the next time you connect.
– – – – server to Inbox on your device. When you select Services> Connect in Inbox, Inbox starts a remote connection using the connection you specified when setting up the current mail service. If you are already connected through a remote connection other than the one you specified in the service, you will be asked if you want to use the current connection. If you choose not to, you will need to disconnect from the current connection before you can check for new messages.
* entry rather than dragging and dropping it. Also, be sure to set your IMAP4 service to receive full copies of messages, attachments, and meeting requests. For more information on using Journal, see the Help for the desktop version of Outlook. Working with Message Attachments: – If you receive messages through a remote mail server, in Inbox on the device, select the Get file attachments and meeting requests (IMAP4) or Get meeting requests (POP3) setting in the Inbox Preferences dialog box.
Note: Once you make the above selection, all attachments will be moved to the selected card. * * Delete an attachment: – To delete an attachment from a message you are sending, select the attachment, and then select Edit> Clear or press the DEL key on the keypad.Delete an attachment: – To delete an attachment you have received, delete the message. Attach a file to a message: – With the message open, select File> Attachments> Add Attachment. – Select the file you want to attach.
5.2.3 Internet Explorer With Internet Explorer, you can view Web or intranet Web pages on your device. You will need to use a modem or WLAN to connect to an Internet server provider (ISP) or network. 5.2.3.1 Connect to the Internet Before you can view Web pages, you must set up a remote connection to your ISP or network. 5.2.3.2 Start Internet Explorer * Open Internet Explorer by selecting Start > Programs > Internet Explorer. * To get default home page, navigate to the desired default web page.
5.2.3.4 Set up a proxy server Proxy servers are often used when connecting to the Internet through a local network, such as a corporate network, for added security. * * * * Select View > Internet Options > Connection Tab. Select Access the Internet using a proxy server. Enter the proxy server address and port. For more information, see your administrator. To bypass the proxy server for local address, such as corporate intranet pages, select Bypass proxy for local address. 5.2.3.
* To view your favorite Web sites, select Favorites and the Web site you want to view. Note: To organize your Favorites list, select Favorites > Organize Favorites. 5.2.3.10 Browse Web pages * To move to a page you have previously view, select View > Back * To move to the next page (provided you have viewed it previously), Select View > Forward. * To return to your Home page, select View > Go > Home. 5.2.3.11 Refresh current page * Select View > Refresh. 5.2.3.12 Stop loading a page * Select View > Stop.
5.2.3.16 Save a copy of current page You can save Web pages and view them later when you’re disconnected from the Internet or Intranet without using cached memory. * * Select File > Save As Specify a folder location and give the file name. 5.2.3.17 Copy a Web page to a document * Select all or part of the Web page you want to copy. * Select Edit > Copy. * Go to the document where you want to place the information and select the location. * Select Edit > Paste. 5.2.3.
5.2.4 Media Player The PDT comes with Media Player for Windows CE.NET installed. * * * Open Media Player by selecting Start > Programs > Media Player from the desktop. Select File > Open to open a new media file. Please refer to www.microsoft.com for additional information and help with your Microsoft Windows Media Player. Figure 5.3: Media Player 5.2.5 * * * * Messenger The Windows CE Messenger client application in Windows CE.
5.2.6 Microsoft WordPad You can create and edit documents and templates in WordPad, using buttons and menu commands that are similar to those used in the desktop version of Microsoft Word. You can work with files Normal or Outline view. WordPad documents are usually saved as .pwd files, but you can also save documents in other file formats, such as .rtf or .doc. 5.2.6.
* Move, copy, or delete text – Select the text you want to move, copy, or delete. – To move or delete text, select the Cut button. To copy the text, select the Copy button. – To paste the information, move the insertion point to the desired location, and select the Paste button. Notes: • • To undo an action, select Edit > Undo. To restore the action, select Edit > Redo. 5.2.6.2 Formatting Text * Create bulleted and numbered lists – Select the Bullets or Numbering button. – Type the first item.
* * Change font formatting – Select desired text. – Select the Bold, Italic, or Underline button. – To change the color, select Format > Font and select the color you want from the Color list. Adjust the paragraph alignment – Select the paragraph you want to align. – Select the Align Left, Center, or Align Right button. Note: To see more formatting options, select Format > Paragraph. * Indent a paragraph – Select the paragraph you want to indent. – Select Format > paragraph.
5.2.6.4 Working in Outline View * Switch between Normal and Outline views – Select View > Normal or Outline. * Assign and change outline levels – Select View > Outline. – Select the appropriate buttons on the toolbar. 5.2.6.5 Inserting Symbols * Place the insertion point where you want to insert the symbol. * Select Tools > Insert Symbols. * Select the symbol you want, and then select Insert. Tips: If you select a different font ( or subset of a font), a different set of Symbols will be displayed. 5.2.6.
document, simply open the attachment in your e-mail program or open the file in the WordPad. During conversion, some formatting attributes may be changed or lost. To avoid losing these attributes permanently, close the file after viewing it rather saving the file on your device. If you save the file, save with a different file name. For more information about conversion performed on your device, see the following topics.
• Table of Contents Table of Contents text and some formatting are preserved. However, any text set at right-aligned tab stops may wrap to the next line. • Index Index text and some formatting are preserved. • Tables Tables appear as tab-delimited text. Cells containing wrapped text, tabs, or paragraph markers may be difficult to read. Simple tables are displayed accurately and restored when you convert the WordPad file back to a WordPad document.
5.2.7 Remote Connection Using Remote Desktop Connection, you can log on to Windows Terminal Server and use all programs installed on this server. For example, instead of running Microsoft Pocket Word, you can run the desktop version of Microsoft Word. 5.2.7.1 Connecting to Terminal Server * * * * Select Start > Programs > Remote Connection, or run ‘CETSC’ from the command prompt. In the Server box, type or select a Terminal Server name or TCP/IP address, or select a server in the drop-down list.
5.2.8 Windows Explorer Windows Explorer works almost the same on your PDT as it does on your PC. See the topics below for information about the difference in Windows Explorer on your device. Figure 5.5: Windows Explorer 5.2.8.1 Navigating in File View * Go forwards and Back – To go to the previous folder, select Go > Back. – To go to the next folder (which you have just viewed), select Go > Forward.
* – Select File > New Folder. Add a folder to your Favorites list – Open the folder – Select Favorites > Add to Favorites. – In the Name box, type the shortcut name. Tips: • • * To open a favorite file or folder, select Favorites and then select the folder. To organize your favorites, select Favorites > Organize Favorites. Transfer a file using infrared – To send a file, select it, line up the infrared ports, and select File > Send To > Infrared Recipient.
5.3 DiskOnChip The DiskOnChip let the application or a data file can be stored into the Flash Memory. Note: The DiskOnChip storage memory persists all reset (warm/cold reboot) conditions and software/firmware updates. We strongly recommends installing all applications, applets, programs, and important data files to the DiskOnChip Flash location. Caution: If an application or a data file is only installed or saved in RAM, a hard reset will result in the loss of that application or data file. 5.3.
5.3.3 DiskOnChip Size The size of the DiskOnChip will vary, depending on the size of system firmware. * * Inside the DiskOnChip directory, tap File > Properties. The DiskOnChip Properties dialog: The number following Free is the amount of memory currently available on your device. Figure 5.
MARS-1030 User Manual 150
APPENDIX A Barcode Setting
A.1 Setup Tab Function Explaining: Item Symbology Setup Decoder Setup Options MARS-1030 User Manual Function Explaining Selecting the Symbology Setup menu item causes the symbology setup dialog to be displayed. This dialog consists of a symbology drop down list, plus four buttons and a message box. Selecting the decode menu item displays the decode options dialog box.
Item Save Current Config to File Restore Config From File Exit Function Explaining The application has the ability to save the Config file. The Config file that is saved when this item is selected depends on the Config that is active. You will be presented with a "Rea ..." dialog where you are asked to select the name of the file to save. The default file extension matches the current active Config. Saving a Config file this way is independent from the Config Format option of the Imager menu.
A.1.1 Symbology Setup Selecting the Symbology Setup menu item causes the symbology setup dialog to be displayed. This dialog consists of a symbology drop down list, plus four buttons and a message box. Function Explaining: Item Function Explaining Default Symbol Causes the current symbology shown in the drop down list to be set to internal defaults. Default All Symbologies Defaults all symbology options for all symbologies to internal defaults.
A.1.2 Decoder Setup Function Explaining: Item No Read Timeout Multiple Symbols Mode Function Explaining Maximum time (in milliseconds) that the imager will attempt to decode before declaring a “No Decode” condition. If attempting to decode using the trigger key, the imager quits decode attempts even if the trigger key remains depressed. You will not be able to start a new decode using the trigger until after the trigger is released.
Item Function Explaining Aimers During Capture Enables/Disables aimers during decoding. Center Window A decoded symbol is returned only if it intersects a Decode Enable rectangle specified by the center window. Center Window indicates the percent-age of width and height of the center decode rectangle, relative to the Center Window entire image. The limits are 0-100%. The defaults are20x20 (128x96 pixels).
A.1.3 Options Function Explaining: Item Trigger Timeout Termination Code Beep after data collect Function Explaining Select the scanning timeout duration (in seconds) from this pull-down list. <3 ~ 10 sec, Default: 6> None After showing barcode, do not action. After showing the barcode, jump to next CRLF row. Space After showing the barcode, jump one unit. Tab After showing the barcode, jump a section. Select the time of beep tone after data collect.
A.
Function Explaining: Item Function Explaining When this item is selected, the imager is queried for the current firmware version information. The Firmware Revision version information is then displayed in the text window. This item allows new engine firmware to be installed into the imager. When Flash New Firmware is selected; you are prompted to select the firmware file. The file, which must have the extension ".bin", must reside on the PDT.
A.3 Symbologies List A.3.1 Aztec Function Explaining: Item Explaining Symbol Enable Enable Aztec Runes Message Length MARS-1030 User Manual Enable this barcode If you are scanning Aztec Runes, which are the smallest type of Aztec Code symbol with the ability to encode a very short license plate message. The minimum and maximum length ranges for the barcode are 1-3750.
A.3.2 Codabar Function Explaining: Item Explaining Symbol Enable Check Char/Digit Enable Check Char/Digit Transmit Start/Stop Transmit Message Length Enable this barcode The scanner reads barcode data with a check digit. If not checked, the bar code will be read as though no check digit was present. The scanner will only read Codabar bar codes printed with a check digit, and will transmit this character at the end of the scanned data. This setting is only valid if check char/digit is enabled.
A.3.3 Code 11 Function Explaining: Item Explaining Symbol Enable Enable this barcode. This option sets whether 1 or 2 check digits are required with Code 11 barcode. The minimum and maximum length ranges for the barcode are 1-80. Check Char/Digit Enable Message Length Check Digits Required Default = Two Check Digits.
A.3.4 Code 128 Function Explaining: Item Explaining Symbol Enable Message Length Enable this barcode The minimum and maximum length ranges for the barcode are 0-80.
A.3.5 Code 39 Function Explaining: Item Explaining Symbol Enable Check Char/Digit Enable Check Char/Digit Transmit Start/Stop Transmit MARS-1030 User Manual Enable this barcode The scanner reads barcode data with a check digit. If not checked, the barcode will be read as though no check digit was present. The scanner will only read Code 39 barcode printed with a check digit, and will transmit this character at the end of the scanned data. This setting is only valid if check char/ digit is enabled.
Item Explaining If this box is checked, the scanner can Append Mode Enable append the data from several Code 39 barcode together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 39 barcode that start with a space (excluding the start and stop symbols), and doesn’t immediately transmit the data. The scanner stores the data in the order in which the barcode are read, deleting the first space from each.
A.3.6 Code 49 Function Explaining: Item Explaining Symbol Enable Message Length MARS-1030 User Manual Enable this barcode The minimum and maximum length ranges for the barcode are 1-81.
A.3.7 Code 93 Function Explaining: Item Explaining Symbol Enable Message Length Enable this barcode The minimum and maximum length ranges for the barcode are 0-80.
A.3.8 Composite Codes Function Explaining: Item Explaining Symbol Enable Enable this barcode. Enable Whether want to scanning UPC-A/EAN-13 Composite codes. UPC-A/ EAN-13 Composite Message Length MARS-1030 User Manual The minimum and maximum length ranges for the barcode are 1-2435.
A.3.9 Data Matrix Function Explaining: Item Explaining Symbol Enable Message Length Enable this barcode The minimum and maximum length ranges for the barcode are 1-1500.
A.3.10 EAN-8 Function Explaining: Item Explaining Symbol Enable Enable this barcode The output of the check digit at the end of the scanned data. Option allows decoding and outputting of a 2 digits addendum on the end of all Enable 2 Digit Addenda scanned EAN-8 data. Option allows decoding and outputting of a 5 digits addendum on the end of all Enable 5 Digit Addenda scanned EAN-8 data. Only reads EAN-8 barcodes that have Addenda Required addenda.
A.3.11 EAN-13 Function Explaining: Item Explaining Symbol Enable Enable this barcode The output of the check digit at the end of the scanned data. Option allows decoding and outputting of a 2 digits addendum on the end of Enable 2 Digit Addenda all scanned EAN-13 data. Option allows decoding and outputting of a 5 digits addendum on the end of Enable 5 Digit Addenda all scanned EAN-13 data. Only reads EAN-13 barcodes that Addenda Required have addenda.
A.3.12 Interleaved 2 of 5 Function Explaining: Item Explaining Symbol Enable Check Char/Digit Enable Check Char/Digit Transmit Message Length MARS-1030 User Manual Enable this barcode The scanner reads barcode data with a check digit. If not checked, the barcode will be read as though no check digit was present. The scanner will only read Interleaved 2 of 5 barcodes printed with a check digit, and will transmit this character at the end of the scanned data.
A.3.13 MaxiCode Function Explaining: Item Explaining Symbol Enable Message Length Enable this barcode The minimum and maximum length ranges for the barcode are 1-150.
A.3.14 MicroPDF417 Function Explaining: Item Explaining Symbol Enable Enable this barcode Message Length The minimum and maximum length ranges for the barcode are 1-366.
A.3.15 OCR-A, OCR-B, US Currency Use this section to program the imager to read machine readable fonts used in optical character recognition (OCR). The imager reads 6 to 60 point OCR typeface.
• U.S. Currency Serial Number (Money) • MICR E-13B • SEMI Font You can either select an OCR default, or create your own custom template for the type of OCR format you intend to read. See "OCR Templates" if you want to create a custom “template” or character string that defines the length and content of OCR strings that will be read with your imager. Note: Setting the template and check character options are essential for OCR reading.
you know the orientation of the characters that are being read in relation to the imager (e.g., 80086996 could read as 80086996 or 96698008). Default = Left-to-Right (LtoR) OCR Templates You can create a custom “template”, or character string that defines the length and content of OCR strings that will be read with your imager. There are several choices when creating a custom template for your application.
To Add an OCR Template 1. Turn on the OCR font you want to read. 2. Begin building the template. Scan the Enter OCR Template symbol. 3. Scan the characters for the string. Use the Template Characters chart above to determine what characters you need to create your format. Use the OCR Programming Chart (after the Sample Codes in the back of this manual) to scan the characters for your template. Example: You need to read any combination of eight digits.
d three more times. Scan Save OCR Template. This would let you read any string of three digits, “ABC,” then any string of three digits, for example: Adding Spaces You may also need to put spaces in your template. Example: You need to read three digits, space, three specific characters (ABC), space, three digits. The template would be: To create this template, you would enable the OCR-A font. Scan the Enter OCR Template symbol.
Example: You need to read any combination of eight digits, or a combination of four digits, two uppercase letters, and two digits. The template would be: To create this template, you would enable the OCR-A font. Scan the Enter OCR Template symbol. Scan the d from the OCR Programming Chart in the back of this manual eight times, then scan the t to create the “or” statement. Then you would scan the characters for the second template. Scan d four times, scan l two times, then scan d two more times.
Exit Selections 181 Chapter A
ASCII Conversion Chart (Code Page 1252) MARS-1030 User Manual 182
ASCII Conversion Chart (Code Page 1252) 183 Chapter A
OCR Programming Chart MARS-1030 User Manual 184
Programming Chart 185 Chapter A
MARS-1030 User Manual 186
A.3.16 PDF417 Function Explaining: Item Explaining Symbol Enable Message Length Enable this barcode The minimum and maximum length ranges for the barcode are 1-2750.
A.3.17 Postnet Function Explaining: Item Explaining Symbol Enable Enable this barcode Check Char/Digit Transmit MARS-1030 User Manual The scanner will only read US Postnet bar codes printed with a check character, and will transmit this character at the end of the scanned data.
A.3.18 QR Code Function Explaining: Item Explaining Symbol Enable Enable this barcode Message Length The minimum and maximum length ranges for the barcode are 1-3500.
A.3.19 Reduced Space Symbology Function Explaining: Item Explaining RSS Expanded Enable Enable RSS Expanded code RSS Limited Enable Enable RSS Limited code RSS 14 Enable Enable RSS 14 code Message Length MARS-1030 User Manual The minimum and maximum length ranges for the barcode are 4-74.
A.3.20 UPC-A Function Explaining: Item Explaining Symbol Enable Enable this barcode The output of the check digit at the end of the scanned data. Option allows decoding and outputting of a 2 digits addendum on the end of Enable 2 Digit Addenda all scanned UPC-A data. Option allows decoding and outputting of a 5 digits addendum on the end of Enable 5 Digit Addenda all scanned UPC-A data. Only reads UPC-A barcodes that have Addenda Required addenda.
A.3.21 UPC-E Function Explaining: Item Explaining Symbol Enable Check Char/Digit Transmit Enable 2 Digit Addenda Enable Expanded UPC-E Enable this barcode The output of the check digit at the end of the scanned data. Option allows decoding and outputting of a 2 digits addendum on the end of all scanned UPC-E data. Enable UPC-E Expanded code Option allows decoding and outputting of a 5 digits addendum on the end of all scanned UPC-E data. Only reads UPC-E barcodes that have Addenda Required addenda.
A.3.22 UPC-E1 Function Explaining: Item Explaining Symbol Enable Enable this barcode The output of the check digit at the end of the scanned data. Option allows decoding and outputting of a 2 digits addendum on the end of all scanned UPC-E1 data.
A.3.
A.3.
A.3.
A.3.26 Australian Post Function Explaining: Item Explaining Symbol Enable Enable this barcode Send Bar Australian Post is a 4-state symbology that was designed with a non-defined user area. The user can define how that area field is interpreted. Most systems have dedicated decoders that don’t know how to decode a symbology that is not defined. If you select the Send Bar Width Data, the bar levels will be outputted (0-3 for the four states) so that the receiving device can then decode appropriately.
A.3.27 IATA 2 of 5 Function Explaining: Item Explaining Symbol Enable Enable this barcode Message Length The minimum and maximum length ranges for the barcode are 1-48.
A.3.28 Codablock F Function Explaining: Item Explaining Symbol Enable Enable this barcode Message Length The minimum and maximum length ranges for the barcode are 1-2048.
A.3.
A.3.30 Planet Code Function Explaining: Item Explaining Symbol Enable Enable this barcode Check Char/Digit Transmit The scanner will only read Planet barcodes printed with a check character, and will transmit this character at the end of the scanned data.
A.3.
A.3.32 MSI Function Explaining: Item Explaining Symbol Enable Enable this barcode Check Char/Digit Transmit Message Length The scanner will only read MSI barcodes printed with a check character, and will transmit this character at the end of the scanned data. The minimum and maximum length ranges for the barcode are 4-48.
A.3.
A.3.34 Mayrix 2 of 5 Function Explaining: Item Explaining Symbol Enable Enable this barcode Message Length The minimum and maximum length ranges for the barcode are 1-80.
A.3.35 Korean Post Function Explaining: Item Explaining Symbol Enable Enable this barcode Message Length The minimum and maximum length ranges for the barcode are 2-80.
