IPPC-8151S Series 15" XGA TFT LCD Celeron M Fanless Industrial Panel PC with Stainless Steel Chassis User Manual
Copyright The documentation and the software included with this product are copyrighted 2009 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -40° C OR ABOVE 85° C. THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. 1. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it.
Contents Chapter Chapter 1 General Information ....................................... 2 1.1 1.2 Introduction ....................................................................... 2 Specifications .................................................................... 3 1.3 1.4 I/O View............................................................................ 4 Dimensions........................................................................ 5 Stand Kit................................................
IPPC-8151S User Manual viii
CHAPTER 1 General Information Sections include: • Introduction • Specifications • Dimensions
Chapter 1 General Information 1.1 Introduction The IPPC-8151S is designed with a fully sealed stainless steel enclosure and uses a special tapered & food safe rubber seal between the bezel and the touchscreen. This allows it to satisfy the stringent standards required in food processing, clinical, chemical or pharmaceutical laboratories. Its fully enclosed design without ventilation slots and external fans makes its completely protected against splashed water, achieving a NEMA4 (IP66) grade of protection.
1.2 Specifications 1.2.1 General Dimensions (W x H x D): Front Panel: 400 x 313.6 x 91.24 mm Control Box: 385.3 x 255.3 x 66/81.2 mm Cut out Dimensions: 388 x 301.5 mm Weight: 13 kg (28 lb) Power Supply: 85W Input Voltage: 10~30Vdc Output Voltage: +3.3V@8A,+5V@10A,+12V@4A,+5Vsb@0.75A, -12V@1A Disk Drive Housing: Supports 1 x 2.5"SATA HDD, 1 x CompactFlash 1.2.2 System Specifications CPU: Intel Celeron M Yonah 423 1.
1.2.3 LCD Specifications Backlight Life: 50,000 hrs Contrast Ratio: 400:1 Display Size: 15" Display Type: XGA TFT LCD Luminance: 350 cd/m2 Max. Colors: 262,144 Max. Resolution: 1024 x 768 Viewing Angle (H/V° ): 120/100 1.2.4 Touchscreen Specifications Lifespan: 10 millions times touch at single point Light Transmission: >80% Type: Analog resistive 5-wire 1.2.
1.4 Dimensions 110.00 [4.33] 7.35 [0.29] 27.65 [1.09] 232.60 [9.16] 2.00 [0.08] 91.24 [3.59] 66.00 [2.60] 11.00 [0.43] G H J 400.00 [15.75] 385.30 [15.17] Chapter 1 5 385.30 [15.17] 110.00 [4.33] 313.60 [12.35] 35.00 [1.38] 7.20 [0.28] 255.30 [10.05] 110.00 [4.33] 308.70 [12.15] 110.00 [4.33] 85.00 [3.35] 400.00 [15.75] 19.65 [0.77] 110.00 [4.33] 85.00 [3.35] 110.00 [4.33] 19.65 [0.77] 90.00 [3.54] 85.00 [3.35] 90.00 [3.54] 85.00 [3.35] 7.15 [0.28] 10.40 [0.41] 299.20 [11.
IPPC-8151S User Manual 6
CHAPTER 2 System Setup Sections include: • Enclosure Kit • Desktop Kit • VESA Arm Kit • Panel Mounting • Installing I/O Cables • Installing a 2.
Chapter 2 System Setup 2.1 Enclosure Kit With IPPC-8151S enclosure kit (P/N: IPPC-8151S-EMKE), IPPC-8151S can provide all-around IP66 waterproof and dustproof protection. Please follow the instruction below to make sure IP66 protection. 1. Put IPPC-8151S into the enclosure kit 2. Use the fixture to make sure IPPC-8151S is closed tightly with the enclosure kit. Please also use the pad to avoid the scratch on surface while screwing.
2.2 Stand Kit With IPPC-8151S stand kit (P/N: IPPC-8151S-SMKE), IPPC-8151S can stand on the desk, install on the wall or ceiling to meet the environment requirement. The stand kit also supports 360 degree C adjustment for the different view angle. The instruction below shows how to install and use the stand kit. 1. Use the screws from the accessory box of the stand kit to fix the stand kit in both sides. 2. Use the thumb screw to adjust the different view angle or desk, wall or ceiling install. 2.
2.4 Install Panel Mount 1. Take the mounting brackets out of IPPC-8151S accessory box. 2. Attach the four mounting brackets by inserting the screws into the keyhole slots on the cover of the monitor. 3. Use the screws to secure the brackets to the cover. Tighten the screws to secure the monitor to the back panel. 2.5 Installing I/O Cables Open the cover from the rear and bottom. Put the cables through the rear hole to the bottom. Connect the cables through the bottom. 2.6 Install a 2.
2.7 Installing a PCI Expansion Card 1. Unscrew the rear cover and open it. 2. Remove the the slot bracket. 3. Insert the add-on card, and close the rear cover 2.8 Installing a Power Connector 1. Use the tool from the accessory box 2.
IPPC-8151S User Manual 12
CHAPTER 3 Jumper Settings & Connectors Sections include: • Jumpers Settings
Chapter 3 I/O Connector & Setting Mode 3.
1 CON.
CN18 BOOT Ctrl CN19 SNMP I2C BUS CN20 CN21 SA1 SA2 JP1 BUZZER OUTPUT ATX Power-input SATA1 SATA2 LVDS PWR Select JP2 CLEAR CMOS JP3 BATTERY Verify JP4 LVDS PANEL Sel. Receive external push-button signal / reset / HDDLED I2C bus for SNMP measure, WINBOND W83782G External buzzer output, depend on CN11 Standard ATX Power input Primary IDE, Master Primary IDE, Slave For 5V Panel: 1-2 (default) , For 3.
3.1.
IPPC-8151S User Manual 18
CHAPTER 4 Intel Chipset Sections include: • Overview • Utilities and Drivers • Dual Display Setting • Touchscreen Installation & Configuration
Chapter 4 Software Configuration 4.1 Overview In IPPC-8151S , Advantech provides a CD-ROM with utilities and drivers included. Please install the Chipset INF driver, VGA graphics driver, LAN driver, audio driver , Touch Screen driver , Watchdog Timer (WDT) driver sequentially. 4.2 Utilities and Drivers The following utilities and drivers are provided with IPPC-8151S. You can also find out the updated description of the utilities and drivers in the ReadMe.txt file on the CD-ROM.
Audio Driver Path: \ audio\ Available for the OS’s below, • Microsoft Windows 2000 • Microsoft Windows XP Touchscreen Driver Path: \Touchscreen Driver\DMC 9000 (Combo) Available for the OS’s below, • Microsoft Windows 2000 • Microsoft Windows XP and more, on the driver CD-ROM.
4.2.1 Touchscreen Gesture Introduction Through the touchscreen gesture, the system can disable/enable touch screen functionality, execute hotkeys, execute applications or power on/ off the system. Please refer to 4.2.2 for more details. 4.2.2 Touch Gesture Utility Enabling Touch Gesture: There are two ways to enable touch gesture utility. One is to click PM icon in right side of task bar and select gesture enable. Two is to go to PenMount control panel and click gesture enable button.
Touch Gesture Utility Setup Please go to PenMount control panel and click gesture setting button. A. Enable / Disable Touch Gesture B. Gesture Sensing Time The time is to complete one gesture. Value can be set from 200ms to 2500ms. C. Gesture Setting The setting for the individual gesture. The blue color means the gesture has been enabled. The gray color means the gesture has been disabled. D. Disable the individual gesture E.
Gesture Default Setting Page Up Zoom In ([Pad] +) Page Down Zoom Out ([Pad] -) Backward (Left Arrow) Rotate Counter Clockwised (Ctrl + L) Forward (Right Arrow) Rotate Clockwised (Ctrl + K) Copy (Ctrl + C) Open On-Screen Keyboard Paste (Ctrl + V) Save Document (Ctrl + S) Undo (Ctrl + Z) Close Program (Alt + F4) Delete IPPC-8151S User Manual 24
A APPENDIX 2 Watchdog Timer Programming
Appendix A WDT Programming A.1 Overview The IPPC-8151S cards’ watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function after the programmed period. This section describes the operation of the watchdog timer, and how to program it. The watchdog timer is built into the super I/O controller SMSC SCH3114. It provides the following functions for user programming: • Can be enabled and disabled by user's program.
A.2 Watchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. You must first assign the address of register by writing address value into address port 2E(hex), then write/read data to/from the assigned register through data port 2F (hex). Table A.
A.3 Example Programs 1.
mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; select WDT pin ;---------------------------mov dx, bx add dx, 47h mov al, 0Ch out dx, al ;---------------------------; select WDT timeout unit ;---------------------------mov dx, bx add dx, 65h mov al, 80h out dx,
;---------------------------; select WDT timeout value ;---------------------------mov dx, bx add dx, 66h mov al, 10 out dx, al ; 10 seconds 2.
mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx mov ah, al mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; select WDT pin ;---------------------------mov dx, bx add dx, 47h mov al, 0Ch out dx, al 31 Chapter A
;---------------------------; select WDT timeout unit ;---------------------------mov dx, bx add dx, 65h mov al, 00h out dx, al ; minute ;---------------------------; select WDT timeout value ;---------------------------mov dx, bx add dx, 66h mov al, 5 out dx, al ; 5 minutes 3.
out dx, al mov dx, 2Fh mov al, 0ah out dx, al ;---------------------------; get base address ;---------------------------mov al, 60h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx shl al, 8 mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al 33 Chapter A
;---------------------------; select WDT configuration ;---------------------------mov dx, bx add dx, 67h in al, dx or al, 04h out dx, al ; reset upon mouse interrupt 4.
;---------------------------mov al, 60h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx shl al, 8 mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; select WDT configuration ;---------------------------mov dx, bx add dx, 67h in al, dx 35 Chapter A
or al, 02h out dx, al ; reset upon keyboard interrupt 5.
shl al, 8 mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; Force timeout ;---------------------------mov dx, bx add dx, 68h in al, dx or al, 04h out dx, al ; force timeout 37 Chapter A
IPPC-8151S User Manual 38
