IPC-6806S Wallmount IPC Chassis for 6 Half-sized Cards User Manual
Copyright Notice The documentation included with this product is copyrighted 2005 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately.
13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 14. If one of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user manual. e. The equipment has been dropped and damaged. f.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen. 7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden. 8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte. 9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden. 10.
Batterie nur gleicher oder entsprechender Type, wie vom Hersteller empfohlen. Entsorgen Sie Batterien nach Anweisung des Herstellers. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A) oder weiger. Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.
Contents Chapter 1 General Information ....................................... 2 1.1 1.2 1.3 1.4 1.5 1.6 Chapter Introduction ............................................................. Specifications .......................................................... Environmental Specifications ................................. Power Supply .......................................................... Passive Backplanes Options.................................... Dimensions of IPC-6806S..........................
B.2.2 Connectors ........................................................... 28 B.2.3 Connector Pin Definition .....................................
1 CHAPTER 2 General Information
Chapter 1 General Information 1.1 Introduction Specially designed for the factory floor and other harsh industrial environments, the IPC-6806S IPC chassis is ideal for system integrators or users who require a compact and rugged system. The chassis comes with a 1U-high 150 W ATX power supply and can accept one 3.5" FDD, one internal 3.5" HDD, and a 6-slot passive backplane to support up to six half-sized cards. With the supplied mounting brackets, the IPC-6806S can be easily mounted on panels or walls. 1.
• Vibration (5 ~ 500 MHz): – (Operating) 0.5 Grms – (Non-operating) 2 G • Shock: – (Operating) 10 G with 11 ms duration, half sine wave – (Non-operating) 30 G with 11 ms duration • Acoustic Noise: < 52 dB sound pressure at 5 ~ 28° C (41 ~ 82° F) • Altitude (Operating): 0 to 3,048 m (0 ~ 10,000 ft) • Safety: CE compliant, UL/cUL approved 1.
1.6 Dimensions of IPC-6806S Figure 1.
Figure 1.
IPC-6806S User Manual 6
CHAPTER 2 2 System Setup
Chapter 2 System Setup The following procedures are provided to assist you in installing a backplane, CPU board, drives, and add-in cards into IPC-6806S chassis. Please also refer to the Appendix A, Exploded Diagram, for the name of each part referred to in this manual. Note To shorten the total system installation time, we suggest users install a passive backplane first, then CPU and add-in card(s), and finally, the drive bay.
2.1 Opening the cover To open the cover of the IPC-6806S, proceed as follows. 1. Remove two screws (one on each side) which secure the cover to the card cage (see Figure 2-1). 2. Lift the lid to expose the interior of the chassis. Figure 2.
2.2 Installing passive backplane & CPU card IPC-6806S accepts a 6-slot passive backplane to support up to six halfsized cards. To install a backplane and a CPU card, refer to Figure 2-2 and proceed as follows: CPU CARD EMI SPRING PLATE BACKPLANE Figure 2.
1. Referring to Figure 2-2, carefully place the passive backplane and EMI spring plate in the IPC-6806S chassis and fix it with screws. For the bare IPC-6806S chassis, the EMI spring plate is stored in the accessory box. 2. Before installing the CPU card, check all devices, such as CPU, CPU cooler, and RAM modules, then make sure they have been installed on the CPU card correctly. 3. Carefully insert the CPU card in to the master slot of the backplane.
2.3 Installing disk drives IPC-6806S accepts one floppy disk drive, and one internal SATA/ATA HDD. To install the disk drives, refer to Figure 2-3 and proceed as follows: Figure 2.3: Installing drives 2.3.1 Hard disk drive 1. Detach the HDD mounting brackets by removing the four retaining screws. 2. Refer to Figure 2-3, align the holes on each side of the HDD with those of the HDD mounting brackets and fix the HDD with screws. 3.
2.3.2 Floppy disk drive 1. Remove the blanking covers of the 3.5" drive bay. 2. Referring to Figure 2-3, insert a FDD into the drive bay with the base facing inward. Fix the drive with screws. 3. Connect 34-pin flat cable from the CPU card to the FDD. 4. Plug a floppy drive power connector into the FDD. 2.4 Installing add-in cards IPC-6806S can accept up to six half-sized cards (including a CPU card) via the supported passive backplane.
1. Find the slot(s) in which card(s) are to be inserted and remove the slot's blank bracket(s) attached to the rear plate of the chassis. 2. Insert a plug-in card. Make sure that the card bracket has been inserted properly. Fasten the card at the top of the bracket with a screw. 3. Repeat Step 2 if there is more than one card.
2.5 Installing wallmount brackets IPC-6806S provides a pair of wallmount brackets in the accessory pack. To wall-mount your chassis, refer to Figure 2-5 and proceeds follows. Figure 2.5: Install wallmount brackets 1. Attach the wallmount brackets to the bottom of the chassis and fix them with the six provided screws. 2. Secure the chassis to the wall with four screws provided. Make sure that the chassis is mounted securely.
IPC-6806S User Manual 16
CHAPTER 3 2 Operation
Chapter 3 Operation 3.1 The Front Section of IPC-6806S 3.1.1 Switches Two switches are used for system power on-off and system reset. • System Reset Switch: Press this switch to reinitialize the system. • Power On-Off Switch: Use this switch to turn on/off the system power. 3.1.2 LED indicators Two LEDs are placed to indicate the system status. Please refer to Table 3-1 for the LED summary. Table 3.
3.2 Replacing the fan and fan filter To replace the system fan or fan filter at the front end of the chassis, refer to Figure 3-1 and proceed as follows: Figure 3.1: Changing the fan and filter 3.2.1 Replace the fan filter 1. Remove the two screws located at the bottom of the filter cover. Gently but firmly pull the fan filter cover free from the chassis. 2. Remove the fan filter and replace it with a new one. 3.2.2 Replace the system fan 1. Remove the fan holder from the chassis. 2.
3.3 Replacing the power supply IPC-6806S supports a single 1U-high power supply. To change the power supply, refer to Figure 3-2 and proceed as follows: Figure 3.2: Changing the power supply 1. Unplug the power cord from the power supply of the IPC-6806S. 2. Open the top cover of the chassis. 3. Unplug the ATX power connector from the passive backplane, +12V power connector from the CPU card, and the peripheral power connector(s) from the drive disk(s). 4.
A APPENDIX 2 Exploded Diagram
Appendix A Exploded Diagram Figure A.
B APPENDIX 2 Passive Backplanes
Appendix B Passive Backplanes B.1 PCA-6106-B: 6-slot ISA backplane B.1.1 Dimension Drawing Size: 140.
B.1.2 Connectors Connector Description ISA1 ~ 6 16-bit ISA bus connector KB1 KB-In, from CPU card K/B connector KB2 ~ 3 KB-Out, 5-pin external K/B connector AT1 AT power connector ATX1 ATX power connector CN1 PS-ON function, 3-pin connector to CPU card for ATX signal CN2 8-pin alarm board power connector CN3 3-pin +5V and +12V power connector B.1.
ATX1 Connector Pin Signal Pin Signal Pin Signal Pin Signal 1 +3.3V 6 +5V 11 +3.3V 16 GND 2 +3.3V 7 GND 12 -12V 17 GND 3 GND 8 NC 13 GND 18 -5V 4 +5V 9 +5VSB 14 PS-ON 19 +5V 5 GND 10 +12V 15 GND 20 +5V CN1 Connector Pin Signal 1 PS-ON 2 GND 3 +5VSB CN2 Connector Pin Signal Pin Signal Pin Signal Pin Signal 1 +5VSB 3 GND 5 +5V 7 -12V 2 GND 4 -5V 6 +3.
B.2 PCA-6105P5-0B1: 5-slot PCI backplane B.2.
B.2.2 Connectors Connector Description PICMG1 CPU-PCI connector PCI1 ~ 4 32-bit PCI bus connector KB1 KB-In, from CPU card K/B connector KB2 ~ 3 KB-Out, 5-pin external K/B connector BIG1 Peripheral power connector AT1 AT power connector ATX1 24-pin ATX power connector CN1 PS-ON function, 3-pin connector to CPU card for ATX signal CN2 8-pin alarm board power connector CN3 3-pin +5V and +12V power connector CN4 3-pin +12V fan connector B.2.
ATX1 Connector Pin Signal Pin Signal Pin Signal Pin Signal 1 +3.3V 6 +5V 11 +3.3V 16 GND 2 +3.3V 7 GND 12 -12V 17 GND 3 GND 8 NC 13 GND 18 -5V 4 +5V 9 +5VSB 14 PS-ON 19 +5V 5 GND 10 +12V 15 GND 20 +5V CN1 Connector Pin Signal 1 PS-ON 2 GND 3 +5VSB CN2 Connector Pin Signal Pin Signal Pin Signal Pin Signal 1 +5VSB 3 GND 5 +5V 7 -12V 2 GND 4 -5V 6 +3.
BIG1 Connector Pin Signal 1 +12V 2 GND 3 GND 4 +5V IPC-6806S User Manual 30
