IPC-644 Series 4-slot MicroBox IPC Chassis User's Manual
Copyright Notice This document is copyrighted, May 1999, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd.
Contents Chapter 1 General Information 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Introduction .......................................................... 1 Specifications ...................................................... 1 Dimensions .......................................................... 4 Mounting .............................................................. 5 IPC-644 Exploded Diagrams ............................... 6 PCA-6104-B Diagram .......................................... 7 PCA-6104NP2 Diagram ........
Chapter 1 General Information 1.1 Introduction The IPC-644 MicroBox IPC chassis is an ultra-compact 4-slot mini-node chassis that is ideal for embedded applications. Its small size enables it to fit in mobile environments such as boats, cars and other vehicles. Naturally, indoor operation is equally suitable. The IPC-644 comes with a 4-slot backplane. You can choose between a 4 ISA backplane, or a 1 ISA / 2 PCI / 1 NLX backplane, both of which can hold up to 4 half-size cards.
1.2 Specifications General • Construction: Heavy-duty steel • Controls: AC power on/off and reset switches • Cooling fans: One 49 CFM filtered cooling fan for inward airflow, and one 14 CFM cooling fan (flow-in) for outward airflow • Mounting: On wall or desktop • Dimensions (W x H x D): 135 x 209 x 305 mm (5.3" x 8.2" x 12") • Weight: 3.83 kg (8.4 lbs) • Driver bay: Vibration damped; holds one 3.5" FDD and one 3.
Power supply PS-80 • Output rating: 80 watts maximum • Input voltage: 85 ~ 264 VAC @ 47 ~ 440 Hz • Output voltage: +5 V @ 8 A, +12 V @ 3.
1.
1.4 Mounting The IPC-644 can either be wall mounted or desktop mounted. Refer to the figures below for how to install the brackets.
1.
1.
1.
Chapter 2 System Setup Installation procedures for the IPC-644 are described below. WARNING: Before starting the installation procedures, make sure you disconnect all power from the chassis. Unplug the power cord from the power outlet in the wall. Merely turning off the power switch is not sufficient. If you are not sure what to do, consult an experienced technician. 2.1 Removing the Top Cover The first step is to remove the chassis cover. You will need a philips screwdriver to detach all of the 6 screws.
2.2 Replacing the Filter The fan filter is located at the front end of the chassis. Refer to Figure 2-2. 1. Remove the two screws located at the bottom of the filter cover. 2. Detach the filter cover by pulling it downward. 3. Replace the filter with a new one. 4. Re-attach the filter cover and secure the two screws.
2.3 Installing the FDD and HDD The FDD and HDD drive bay is located in the lower deck of the chassis. The upper deck has to be detached first, in order to make the lower deck accessible for installation. Separating the two decks 1. Remove the chassis cover. See Section 2.1 for further information. 2. Unplug both power supply connectors from the backplane. 3. In order to detach the upper deck, remove the four screws. Two of the screws are located at the front of the upper deck, and two at the back. 4.
Figure 2-3: Installing the FDD and HDD Completing the installation 1. Return the drive bay to its original position and re-attach the screws. 2. Put the upper deck back and secure it with the four screws. 3. Plug the power supply connectors back into the backplane. 4. Re-attach the chassis cover.
2.4 Installing the Cards To install slot-board computers and other add-on boards: 1. Remove the chassis cover. Refer to Section 2.1 for further details. 2. Remove the slot cover. 3. Insert the CPU cards or add-on cards vertically and downward into the vacant slots. 4. Align and attach the screws to secure the cards.
14 IPC-644 User's Manual
Appendix A Safety Instructions A.1 English 1. Read these safety instructions carefully. 2. Keep this installation reference guide for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
A.2 Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
