IPC-603MB Ultra Compact 2U-high Rackmount IPC Chassis User Manual
Copyright The documentation and the software included with this product are copyrighted 2005 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure.
Technical Support and Assistance 1. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS. 8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11.
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4.
b. Flüssigkeit ist in das Gerät eingedrungen. c. Das Gerät war Feuchtigkeit ausgesetzt. d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist. 15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batterie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-mahnlichen Typ.
Contents Chapter 1 General Information ....................................... 2 1.1 1.2 1.3 1.4 1.5 Chapter 2 System Setup.................................................... 6 2.1 2.2 2.3 2.4 2.5 Chapter Introduction ....................................................................... 2 Specifications .................................................................... 2 Environmental Specifications ........................................... 3 Power Supply ........................................
IPC-603MB User Manual x
1 CHAPTER 2 General Information
Chapter 1 General Information 1.1 Introduction IPC-603MB is an ultra compact 2U-high rackmount industrial computer chassis designed for space-conscious applications. With only 310 mm depth, IPC-603MB can accept any of Advantech ATX/mATX motherboards, and up to three half-sized add-in cards with the supported riser card. 1.
1.3 Environmental Specifications • Temperature: (Operating) 0 ~ 40° C (32 ~ 104° F) (Storage) -20 ~ 60° C (-4 ~ 140° F) • Humidity: (Operating) 10 ~ 95% @ 40° C, non-condensing • Vibration (5 ~ 500 MHz): (Operating) 1Grms (Non-operating) 2 G • Shock: (Operating) 10G with 11 ms duration, half sine wave (Non-operating) 30G 11 ms duration • Acoustic Noise: < 52dB sound pressure at 5 ~ 28° C (41 ~ 82° F) • Altitude (Operating): 0 to 3,048 m (0 ~ 10,000ft) • Safety: CE compliant, UL/cUL approved 1.
1.
CHAPTER 2 2 System Setup
Chapter 2 System Setup The following procedures are provided to assist you in installing a motherboard, drives, and add-in cards into an IPC-603MB chassis. Refer to Appendix A, Exploded Diagram, for the names of each part used in this manual. Note Figure 2-1 is the summary illustration for installing the whole IPC-603MB system. To shorten the total system installation time, we suggest users to install a motherboard first, then the riser card and add-in card(s), and finally, the drive bay.
2.1 Removing the Cover To remove the top cover of IPC-603MB, please refer to Figure 2-2. Figure 2-2 Removing the top cover 2.2 Installing a Motherboard IPC-603MB accepts both ATX and microATX motherboards. To install a motherboard, refer to Figure 2-1 and proceed as follows: Note Use a CPU cooler that is less than 60 mm high to ensure the best air flow inside the chassis. 1. Remove the three screws from the L-form riser card holder in the IPC-603MB chassis.
3. Note Check all devices, such as CPU, CPU cooler, and RAMs and make sure they have been installed on the motherboard correctly. Carefully place the motherboard in the IPC-603MB chassis and fix it with screws. If you choose Advantech’s AIMB-740, 741, 742, or 762 ATX motherboard, please find a spacer bracket in the accessory bag and mount it on location A in the bottom of the IPC-603MB chassis before installing the motherboard.
6. Connect the power connectors of the two system fans (on the rear plate of IPC-603MB) to the motherboard. 7. Re-install the L-form riser card holder (together with the riser card) and fasten it with screws. 2.3 Installing Disk Drives The IPC-603MB accepts one slim type CD-ROM/-RW and one internal SATA/ATA HDD.
D D H M O R miD l SC Figure 2-5 Place the drive bay bracket kit into IPC-603MB chassis 1. Open the top cover of IPC-603MB chassis. 2. Remove the four screws that mount the drive bay bracket kit in IPC-603MB chassis. 3. Remove the blank cover of the slim-type CD-ROM from the bracket kit. 4. Refer to Figure 2-4 and mount a slim-type CD-ROM/-RW and a 3.5" HDD with screws. 5. Refer to Figure 2-5 to return the drive bay bracket kit into the IPC603MB chassis and fix it with screws. 6.
2.4 Installing Add-in Cards The IPC-603MB can accept up to three half-sized PCI add-in cards via the riser card, which is inserted in the sixth slot of the enclosed ATX motherboard and mounted on the L-form riser card bracket. To install an add-in card, face to the rear side of the chassis and proceed as follows: 1. Find the riser-card slot(s) in which card(s) are to be inserted, then remove the slot’s blank bracket(s) from the front plate of the chassis. 2.
IPC-603MB User Manual 12
CHAPTER 3 2 Operation
Chapter 3 Operation 3.1 The Front Section of IPC-603MB 3.1.1 Switches Two switches are used for system power on-off and system reset. Press the System Reset Switch to reinitialize the system. Press the Power OnOff Switch to turn the system power on or off. 3.1.2 LED indicators Two LEDs indicate the system status. Refer to Table 3-1 for the LED summary. Table 3.
3.2 Replacing the Fans There are two fans on the rear plate of IPC-603MB chassis. To change any failed fan, refer to Figure 3-1 and proceed as follows: 1. Open the top cover of IPC-603MB chassis. 2. Unplug the power connector of a failed fan from the motherboard and the fan filter behind the failed fan. 3. Remove the four screws, which mount the failed fan to the chassis and lift it with two fingers. 4. Place a new fan on the proper location, and fasten it with four screws. 5.
3.3 Replacing the filters To change the filters, refer to Figure 3-2 and proceed as follows: 1. Open the top cover of IPC-603MB chassis. 2. Remove the filter(s) with two fingers and replace it with a new one.
3.4 Replacing the power supply IPC-603MB supports a single 1U-high power supply. To change the power supply, refer to Figure 3-3 and proceed as follows: Floppy Drive Power Connector +12V Power Connector Peripheral Power Connector ATX Power Connector Figure 3-3 Changing the power supply 1. Unplug the power cord from the power supply of IPC-603MB. 2. Remove the top cover of IPC-603MB. 3.
8. Plug the ATX power connector and +12V power connector into the motherboard, and the peripheral power connector(s) into the proper disk(s). 9. Replace the cover of IPC-603MB and plug in the power cord.
A APPENDIX 2 Exploded Diagram
Appendix A Exploded Diagram IPC-603MB User Manual 20
