LTE Industrial Router ICR-2431 USER MANUAL
ICR-2431 c 2023 Advantech Czech s.r.o. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photography, recording, or any information storage and retrieval system without written consent. Information in this manual is subject to change without notice, and does not represent a commitment on the part of Advantech. Advantech Czech s.r.o.
ICR-2431 Used symbols Danger – Information regarding user safety or potential damage to the router. Attention – Problems that can arise in specific situations. Information, notice – Useful tips or information of special interest. Advantech Czech s.r.o., Sokolska 71, 562 04 Usti nad Orlici, Czech Republic Document No. MAN-0058-EN, revision from February 8, 2023. Released in the Czech Republic.
ICR-2431 Contents 1 Product Overview 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 2 Product Introduction . . . . . Product Usage Examples . . Hardware Overview . . . . . Order Codes . . . . . . . . . Package Contents . . . . . . Product Dimensions . . . . . Mounting Recommendations Wall Mounting . . . . . . . . . DIN Rail Mounting . . . . . . Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICR-2431 Appendix C: Regulatory & Safety Information 35 Appendix D: Related Documents 37 iv
ICR-2431 List of Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Access to the Internet from LAN . . . . . . . . . . . . . . . . . . . . . Backed up Access to the Internet . . . . . . . . . . . . . . . . . . . . . Using VPN Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Overview of the Router . . . . . . . . . . . . . . . . . . . . .
ICR-2431 List of Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Hardware Overview of the Router . . . . . Order Codes Overview . . . . . . . . . . . Contents of Package . . . . . . . . . . . . Ethernet Connector Pinout Description . . Power Supply Pinout . . . . . . . . . . . . I/O Ports Pinout . . . . . . . . . . . . . . . Connection of RS485 . . . . . . . . . . . Connection of RS232 . . . . . . . . . . . LED Status Indication . . . . . . . . . . . Basic Parameters . . . . . . . . . . . . . .
ICR-2431 1. Product Overview 1.1 Product Introduction Industrial cellular router ICR-2431 is designed for wireless communication in mobile networks that use traditional cellular technologies. The primary purpose of this router is its use in the Category 4 (Cat.4) services on the cellular LTE network. Cat.4 rated router is capable of achieving typical speeds in 4G coverage areas where the network is enabled with 20 MHz of contiguous spectrum.
ICR-2431 1.2 Product Usage Examples The router is primarily intended for these four basic situations: I. Access to the Internet from LAN Figure 1: Access to the Internet from LAN II.
ICR-2431 III. Secure networks interconnection or using VPN Figure 3: Using VPN Tunnel IV.
ICR-2431 1.3 Hardware Overview The router case preview is shown in Figure 5. A short description of hardware parts of the router is listed in Table 1, including the links to the chapters with a detailed description. Figure 5: Hardware Overview of the Router # Item/Caption Type Description 1 Grounding screw M3 Pay attention to proper grounding; see Chapter 2.4. 2 PWR IN/OUT 6-pin terminal Power supply, binary input, and binary output interfaces. See Chapter 2.4, Chapter 2.5, Chapter 2.
ICR-2431 Continued from previous page # Item/Caption Type Description 5 RST - Button to reboot the router or to restore the default configuration; see Chapter 2.8. 6 ETH0 ETH1 RJ45 RJ45 100 MB Ethernet connections for the first and second LAN; see Chapter 2.3. 7 ANT SMA Connector for the first main antenna of the cellular module; see Chapter 2.2 8 DIV SMA Connector for the first diversity antenna of the cellular module; see Chapter 2.
ICR-2431 1.
ICR-2431 1.6 Product Dimensions For the dimensions of the product see the figures below. Note that all sizes are measured in millimeters.
ICR-2431 Figure 7: Router Dimensions – Top, Sides and Back View with Wall Mount Clip 9
ICR-2431 Variant with DIN Rail Clip Figure 8: Router Dimensions – Bottom and Front View with DIN holder 10
ICR-2431 Figure 9: Router Dimensions – Top, Sides and Back View with DIN holder 11
ICR-2431 1.7 Mounting Recommendations The router can be placed: • on a flat surface, • on a wall using the wall mounting clip (see Chapter 1.8), • on a DIN rail EN 60715 with the metal DIN rail clip (see Chapter 1.9) For most applications with a built-in router within a switchboard, it is possible to recognize two kinds of environments: • A non-public, industry environment of low voltage with high interference, • a public environment of low voltage and without high interference.
ICR-2431 1.8 Wall Mounting The wall mounting clip is supplied with the router as standard accessories. The router can be screwed to a wall (or another surface) using the wall mounting clip. There are two wholes on the clip with a diameter of 4 millimeters. For detailed information about the mounting dimensions see Figure 7 in Chapter 1.6. When mounting the wall mounting clip, tighten the screws with max. torque of 0.4 Nm.
ICR-2431 1.9 DIN Rail Mounting The DIN rail clip is not supplied with the router as standard accessories, but it can be ordered by the order code BB-DIN-ICR32. The DIN rail clip is suitable for a DIN rail according to EN 60715 standard only. The default position of the clip is shown in Figure 11. When mounting the DIN rail clip, tighten the screws with max. torque of 0.4 Nm.
ICR-2431 1.10 Product Label An example of the product label, with all the information printed on it, is in the figure below.
ICR-2431 2. Hardware Functionality See Chapter 1.3 for the product hardware overwiew. Table 1 lists a short description of the hardware, including the links to the chapters with a detailed description. 2.1 SIM Card Slots Slots for two SIM cards are located on the router under a metal cover. If you intend to use this device to communicate over a cellular network, please place an activated data-provisioned SIM card into the SIM card reader.
ICR-2431 2.2 Antennas Connect cellular antennas to the router to main (ANT) and diversity (DIV) SMA connectors on the front panel. Connect WiFi antenna to the WiFi SMA connector on the side of the router. Only run the router with a cellular antenna connected to the main antenna connector, as the energy from the transmission is effectively reflected by the open end and can damage the equipment. Recommended tightening moment for screwing the antenna to the SMA connectors is 0.9 Nm.
ICR-2431 2.4 Power Supply The pins of power supply are physically connected to the 6-pin terminal block panel socket located on the left panel. The connection of power supply is shown in Figure 16 and described in Table 5.
ICR-2431 2.5 I/O Port Interfaces The maximum length of wires connected to the I/O ports is 3 meters to meet the EMC immunity conditions. The pins of I/O interface are physically connected to the 6-pin terminal block panel socket located on the left panel. The pinout of one binary input and one binary output is shown in Figure 18 and described in Table 6.
ICR-2431 2.6 Serial Interfaces The pins of RS232 and RS485 serial interfaces are physically connected to the 7-pin terminal block panel socket located on the left panel. The pinout of this connector is described in Figure 20 and in Table 7, resp. Table 8.
ICR-2431 2.7 LED Status Indication There are LED indicators on the front panel of the router to provide router status information. Moreover, ETH connector, has two additional LEDs providing information about the port status. Caption Color State Description PWR Green Green Green On Blinking Fast blinking The router is booting up. The router booted up and is ready. The router firmware is being updated. USR Green — The function of this LED is user-defined.
ICR-2431 2.8 Reset Functions Consider creating a router configuration backup before performing the router’s factory reset. The RST button can be used in three different scenarios: • Reset: Hold the RST button for less than 4 seconds; the router will reboot, applying its customized configuration. The router reset can be initiated by clicking the Reboot menu item in the router web GUI.
ICR-2431 3. First Use 3.1 Accessories Connection Before putting the router into operation, it is necessary to connect all the components required to run your applications; see Chapter 1.3 for the hardware overview. Remember to insert a SIM card for the cellular connection; see Chapter 2.1. Do not run the router without antenna connected to the main antenna connector as the energy from the transmission is effectively reflected by the open end and can damage the equipment. 3.
ICR-2431 Figure 22: Router’s Web Interface A detailed description of the router settings in the web interface can be found in the configuration manual [1] of the router.
ICR-2431 4. Technical Specifications 4.1 Basic Parameters Router parameters Temperature range Operating Storage -40 ◦ C to +75 ◦ C -40 ◦ C to +85 ◦ C Humidity Operating Storage 5 to 95 % relative humidity non condensing 5 to 95 % relative humidity non condensing Altitude Operating 2000 m / 70 kPa Degree of protection IP30 Supply voltage 9 to 48 V DC Battery for RTC CR2032X (non-replaceable) Consumption Idle Average Maximum 1.9 W 2.8 W 3.
ICR-2431 4.2 Standards and Regulations The router complies with the following standards and regulations: Standards and regulations Radio EN 301 511, EN 301 908-1, EN 301 908-2, EN 301 908-13 EMC EN 301 489-1, EN 301 489-52, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-6-2, EN 55032 Safety IEC 62368-1, AS/NZS 62368.1, IEEE 802.
ICR-2431 4.
ICR-2431 4.4 Parameters of Cellular Module Technical parameters of cellular module Antenna Connector type: SMA Impedance: 50 Ω LTE parameters LTE: LTE Cat.4, 3GPP Rel. 11 FDD frequencies: B28A (700 MHz), B20 (800 MHz), B8 (900 MHz), B7 (2600 MHz), B3 (1800 MHz), B1 (2100 MHz) TDD frequencies: B41 (2500 MHz), B40 (2300 MHz), B38 (2600 MHz) Bit rates: up to 150 Mbps (DL), 50 Mbps (UL) HSPA+/UMTS parameters Supported frequencies: B8 (900 MHz), B1 (2100 MHz) Bit rates: up to 42 Mbps (DL) / 5.
ICR-2431 4.6 Parameters of I/O Ports Electrical characteristics of the binary inputs are in Table 15. Status of the binary input is reported in the GUI on General Status page or can be retrieved in the Shell via io get bin0 command. get command output Voltage Web interface status 0 ≤ 0.8 V (0.5 mA)) On 1 ≥ 2V Off Table 15: Electrical Characteristics of Binary Inputs The maximum binary output load is 100 mA at 9 – 48 V. 4.
ICR-2431 4.8 System Configuration The main parametes of the system are listed in Table 17.
ICR-2431 Appendix A: Troubleshooting If you cannot connect to the router from your PC, your network card may be configured in such a way that it is not possible to connect to the router. Take one or more of the following steps in order to solve the problem: • Make sure your PC’s network card is configured to obtain the IP address form the DHCP server (by default the DHCP server is running in the router). • Connect the router to the PC via Switch.
ICR-2431 ✍ I can’t access my Web server placed behind the router over NAT. • The remote HTTP access to the router has to be disabled on "NAT Configuration" page in the router. Also enable "Send all remaining incoming packets to default server" feature and fill in the IP address of your Web server. On the Web server, the default gateway has to be the IP address of the router. ✍ DynDNS doesn’t work. • With private APN this will not work.
ICR-2431 ✍ Serial communication is not working. • Verify that the router model supports serial communications. Also verify the serial communication settings. To do so, open the router’s configuration menu via the web browser, select the appropriate "Expansion Port" from "Configuration" part of the menu and verify the settings. ✍ Is the router Cisco compatible? Can I use the Cisco configuration? • No, the Firmware in the router (Conel OS) is based on Linux with BusyBox.
ICR-2431 Appendix B: Customer Support Customer Support for Europe Advantech Czech s.r.o. Sokolska 71 562 04, Usti nad Orlici, Czech Republic Phone: Fax: E-mail: Web: +353 91 792444 +353 91 792445 iiotcustomerservice@advantech.eu www.advantech.com Customer Support for NAM Advantech B+B SmartWorx 707 Dayton Road Ottawa, IL 61350 USA Phone: Fax: E-mail: Web: +1-800-346-3119 (Monday – Friday, 7 a.m. to 5:30 p.m. CST) +1-815-433-5109 support@advantech-bb.com www.advantech-bb.
ICR-2431 Appendix C: Regulatory & Safety Information Safety Notices Please, observe the following instructions: • The router must be used in compliance with all applicable international and national laws and in compliance with any special restrictions regulating the utilization of the router in prescribed applications and environments. • To prevent possible injury and damage to appliances and to ensure compliance with all relevant provisions, use only the original accessories.
ICR-2431 Product Disposal Instructions The WEEE (Waste Electrical and Electronic Equipment: 2012/19/EU) directive was introduced to ensure that electrical/electronic products are recycled using the best available recovery techniques to minimize the environmental impact. This product contains high quality materials and components which can be recycled. At the end of it’s life this pro- duct MUST NOT be mixed with other commercial waste for disposal. The device contains a battery.
ICR-2431 Appendix D: Related Documents [1] Configuration Manual for v2i Platform [EP] Product-related documents and applications can be obtained on Engineering Portal at https://icr.advantech.cz/download address.
ICR-2431 We, Advantech Czech s.r.o., declare that the radio equipment narrated in this user’s manual complies with Directive 2014/53/EU. We, Advantech Czech s.r.o., declare that the radio equipment narrated in this user’s manual complies with Radio Equipment Regulations 2017 (S.I. 2017 No. 1206). The full text of the EU Declaration of Conformity is available at the following internet address: icr.advantech.
