FPM-3220 Industrial Control Panel with 12.
Copyright This document is copyrighted February, 2002, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before you set up the FPM-3220, make sure that the following items have been included in your package, and that this manual is in good condition. If anything is missing or damaged, contact your dealer immediately: • • FPM-3220 control panel Accessory pack, including: - FPM-3220 User's Manual - A HMI Products, Drivers, Utilities CD - An AC/DC power adapter - A power adapter mounting bracket - A power connector fix bracket - A 1.8 m Power chord - A 1.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
Table of Contents Contents Chapter 1 Introduction ......................................................1 1.1 1.2 1.3 Introduction ....................................................................... 2 Specifications .................................................................... 2 Complete Functionality ..................................................... 4 Figure 1.1: Front panel layout ............................................... 4 Figure 1.2: Rear chassis layout ..........................
A.3 OSD function and operation............................................ 28 Figure A.1: OSD menu ........................................................ 28 Table A.3: OSD Functionality........................................... 28 Appendix B Touchscreen (optional) ..................................29 B.1 B.2 Specifications .................................................................. 30 Installation of Touchscreen Driver..................................
CHAPTER 1 Introduction • • • • Introduction Specifications Complete Functionality Dimensions 1 Chapter 1 Introduction
Chapter 1 Introduction 1.1 Introduction The FPM-3220 control panel series are the new Advantech LCD control panel with 64 data-entry keys, 10 function keys, 10 unique programmable macro keys and 12 SVGA 800x600 TFT LCD. The strong membrane key function lets FPM-3220 a powerful panel programming benefit like standard workstation, but none of deep space problem.
• Operating temperature: 0° ~ 50° C (32° ~ 122° F) • Relative humidity: 5 ~ 85% @ 40° C, non-condensing • Storage temperature: -20° ~ 60° C • Storage humidity: 5 ~ 95% non-condensing • Dimensions (W x H x D): 482 x 266 x 63 mm (19.0" x 10.5" x 2.5") • Gross Weight: 5 kg (11 lbs) • CE, FCC, BSMI compliant LCD Display • Display type: SVGA TFT LCD • Display size: 12.
1.3 Complete Functionality FPM-3220 features rich and complete functions especially designed for industrial control applications. 12.1” TFT LCD Display with VGA Interface & optional Touchscreen Complete Keypad LCD Backlight Switch LCD Brightness VR Power Indicator Aluminum Panel Compliant with NEMA 4/IP 65 Dust Protection Door PS/2 KB/Mouse Connector Figure 1.
1.4 Dimensions Figure 1.
FPM-3220 User’s Manual 6
CHAPTER 2 System Setup • • • • • • • • Connecting to Controller Install the Power Adapter Connecting External Keyboard and Mouse Panel Mounting Rack Mounting Wall Mounting Desktop Stand Swing Arm Mounting 7 Chapter 2 System Setup
Chapter 2 System Setup 2.1 Connecting the Controller The FPM-3220 is designed to be the operation panel for your system. It’s equipped with PC standard interfaces that are easily found on PC-based controller. There are three connections between the FPM-3220 and the controller: VGA, Keyboard, and optional RS-232 of touch screen. VGA Keyboard/Mouse RS-232 Figure 2.
2.2 Install the Power Adaptor The power adapter could be mounted on the back cover with a power adapter-mounting bracket in the accessory box as following figure shown. In order to secure the power connector, there is a connector fixing plate in the accessory box also, and it could be installed as shown in the following figure. Figure 2.
2.3 Connecting External Keyboard and Mouse You can connect an external keyboard and mouse to FPM-3220. The first place to the connect keyboard and mouse is the PS/2 connector on the front panel, under the dust-protection door. You can connect a PS/2 keyboard to the connector if you do not need a mouse. Or use the Y-cable provided in the accessory box to connect simultaneously a keyboard and a mouse. There is another additional PS/2 keyboard/Mouse connector on the back chassis as shown in figure 2-4.
2.4 Panel Mounting A cutout need be made to accommodate panel mounting. Four panelmount brackets are included in the accessory box. Slide the unit backward into the panel opening. Attach the four mounting brackets by inserting the screws into the keyhole slots on the flat panel monitor cover. Use the screws to secure the brackets to the cover. Tighten to secure the front panel monitor against the back panel. Figure 2.
2.5 Rack Mounting The FPM-3220 can be directly mounted in a standard 19" rack. Just mount the panel on the rack and secure with four screws. Figure 2.
2.6 Wall Mounting First mount the wall/desktop-mounting bracket to the wall, then mount the FPM-3220 on the bracket through the three screws, finally secure the panel to the mounting plate with the locking plate. Figure 2.
2.7 Desktop Stand Mount the wall/desktop-mounting bracket to the back of FPM-3220 with two screws as following drawing shown. Figure 2.
2.8 Swing Arm Mounting There are two sets of Swing-ARM mounting holes, 75 mm and 100 mm format, on the back chassis. You could Mount FPM-3220 on the SwingARM through the mounting holes and secure with four screws. Figure 2.
FPM-3220 User’s Manual 16
CHAPTER 3 Macro Key Programming • • • • • Introduction Macro key overview Syntax Using SFED3220.
Chapter 3 Macro Key Programming 3.1 Introduction Our workstations are equipped with programmable function keys (macro keys) that greatly enhance the operator interface. Macros, which are far more powerful than batch files, automate the most commonly used input sequences. They extended their functional reach to within application programs. 3.2 Macro Key Review The complete macro function consists of the following elements: Macro keys (SF1, SF2,...
3.3 Syntax Macro definitions consist of ASCII characters or character codes for special characters (ALT, ENTER, SHIFT, F1, SF2, and so on). These codes are predefined, and SFED3220.COM will display them on the screen for you. They are easily recognizable, appearing between the square brackets, "[" and "]". For example: ALT is represented by [26] ENTER is represented by [33] In your macro script, you can enter ordinary text (ASCII characters) or the code(s) of the required special character(s).
For example: ALT-F1 is represented by [26][44][90] CRTL-C is represented by [28]C[90] SHIFT-B is represented by [27]B[90] ALT-X is represented by [26]X[90] or [26]x[90] ALT-F1 is represented by [26][44][90] SHIFT-X is represented by [27]X[90] SHIFT-F1 is represented by [27][44][90] CTRL-X is represented by [28]X[90] CTRL-F is represented by [28][44][90] CTRL-ALT-DEL is represented by [28][26][41][90] (reboot) CTRL-ALT-A is represented by [28][26]A[90] CTRL-SHIFT-1 is represented by [28][27]1[90] Another use
3.4 How to use SFED3220.COM First, boot your system under pure DOS mode (not DOS shell in windows) and copy all the files to your hard disk and/or make a backup disk. Then start the macro editor. You will have to specify either an existing macro script file or a new macro script file. Here we will create a new file by typing SFED3220 NEWKEY.TXT [ENTER]. The following screen will appear: Advantech Workstation Special Function Key Edit Program Rev.
3.5 Example We will explain all macro functions that you can find in the EXAMPLE.TXT We will explain all macro functions that you can find in the EXAMPLE.TXT macro script file. When typing SFED3220 EXAMPLE.TXT the following editor screen will appear: Advantech Workstation Special Function Key Edit Program Rev.
SF1 = CD\TOOL[33] SFED825 EXAMPLE.TXT[33] This macro changes to the TOOL directory, then starts up SFED3220.COM with EXAMPLE.TXT. SF2 = COPY C:\CONFIG.EMM C:\CONFlG.SYS [33] Y [33] [85] [79] The configuration information is changed by copying CONFIG.EMM to CONFIG.SYS. After a delay of 5 seconds, [85], the macro invokes macro function key SF10, [79], which was defined to reset the system. SF4 = C:\WP51\WP[33][86][27][4D][90]REPORT.
FPM-3220 User’s Manual 24
Appendix A Display Timing Mode & OSD • • • Supported input timing modes OSD operation keypad OSD function and operation 25 Appx.
Appendix A Display Timing Mode and OSD A.1 Supported Input Timing Modes The nineteen kinds of timings below are already programmed in this module. The input synchronous signals are automatically recognized. Resolution Vertical Frequencies 60 Hz 640 x 480 Yes 800 x 600 Yes 70 Hz 72 Hz 75 Hz Yes Yes Yes Table A.1: Supported Input Formats Note 1: Even if the preset timing is entered, a little adjustment of the functions such as Horizontal period, CLK-delay and display position, are required.
A.2 OSD Operation Keypad The OSD keypad, including six keys and a two color indicator, is designed as the OSD operation interface. The six keypad functions are in Table A-2. Auto Press this button to execute auto adjustment process Sel Press to show the OSD screen or select an item to change its setting To move between items or increase or decrease setting Exit To exit from the current setting in OSD function On/OFF Turns display backlight ON and OFF Table A.
A.3 OSD function and operation Auto-adjustment process or to adjust manually: 1. Press [Sel] button to display the OSD Menu shown below. 2. Press 3. Press [Sel] button to select the menu option. 4. Press 5. Press [Exit] button or wait until time out to save changes and exit the menu or sub-menu. or button to scroll to the desired menu option. or button to adjust the setting. Figure A.1: OSD menu Table A-3 is the OSD menu hierarchy and function description.
Appendix B Touchscreen (optional) • Installation of touchscreen driver 29 Appx.
Appendix B Optional Touchscreen B.1 Specifications Electrical Operating Voltage: 3.3 to 5 VDC typical Sheet Resistance: 350 ± 22% W/square Linearity: +/- 1.5% full scale linearity error in either direction. Insulation Resistance: > 20 ΜΩ @ 25 VDC.
Durability Point Activation Life: 1 Million activations on a single point with a 5/8” diameter silicone finger with a 350 g load at 2 Hz Character Activation Life: >100,000 characters written within a 20mm x 20mm B.2 Installation of Touchscreen Driver The touchscreen for the FPM-3220 Series provides drivers for use with MS-DOS, Windows 3.1, 95, 98, NT, and 2000.
FPM-3220 User’s Manual 32
