FPM-3190 Industrial Flat Panel Monitor with 19" LCD in VGA/Video User’s Manual i
Copyright This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before installing your equipment, make sure that the following materials have been received: •FPM-3190 Series flat panel monitor •Accessory pack, including: - AC/DC adapter - Power Cord - VGA Cable - Component bag - Screw bag - HMI Products, Drivers, Utilities CD - RS-232 cable (FPM-3190TV-TC only) If any of these items are missing or damaged, contact your distributor or sales representative immediately. Additional Information and Assistance 1.Visit the Advantech web site at www.advantech.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
Contents Chapter 1 Introduction ......................................................2 1.1 1.2 Introduction ....................................................................... 2 Specifications .................................................................... 2 1.2 1.2 1.2 Chapter 1.3 LCD Specification ................................................... 3 1.4 Connectors ............................................................... 4 1.5 Dimensions ...............................................
FPM-3190 User’s Manual viii
CHAPTER Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Connectors • Dimensions 1
Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3190 Series is a 19" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touchscreen, the FPM-3190 Series is an excellent and user-friendly system control interface.
• Vibration (operating): 5 ~ 17 Hz, double-amplitude displacement 17 ~ 500 Hz, 1.0 G peak to peak • Dimensions: (W x H x D):482 x 399 x 66 mm (19" x 15.7" x 2.6") • Weight: 10 kg (22 lb) • CE, FCC, BSMI, CCC compliant Touchscreen (Optional) • Type: capacitive sensor • Resolution: 1024 x 1024 • Light transmission: 88% • Operating Pressure: 30 ~ 45 gram for stylus pen, contact bounce < 10 ms • Controller: RS-232 interface • Power Consumption: +5 V @ 200 mA • OS support: MS-DOS, Windows 3.
1.4 Connectors The following connectors are situated on the left hand side of the FPM-3190 Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15pin DB-15 connector located on the left side of the system unit. DVI Port Digital Visual Interface Video Port (RCA Jack) Support NTSC and PAL B, D, G, K, J. S-Video port (Main DIN 4-Pin) The video port/S-video port supports NTSC and PAL B/D/G/K/J. The video/S-video port has been tested with a DVD player.
1.5 Dimensions Figure 1.1: FPM-3190 Dimensions 444 x 377 mm (17.48" x 14.
FPM-3190 User’s Manual 6
CHAPTER 2 System Setup This chapter includes: •Mounting the Monitor - Wall/Panel/Rack Mounting - Desktop Stand/Swing-ARM Mounting
Chapter 2 System Setup 2.1 Mounting the Monitor The FPM-3190 Series can be placed as you require. The versatility of the FPM-3190 mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting With wall brackets, the FPM-3190 can be mounted directly to a wall. If you need to install the FPM-3190 in different ways, release the mounting brackets by detaching the four screws on the rear side. Figure 2.
2.1.2 Panel Mounting If you need to install the FPM-3190 series on a panel mount, please release the mounting brackets by detaching four screws on rear side and fix them on up and bottom side by screws. Figure 2.
2.1.3 Rack Mounting FPM-3190 series products could be directly mount to the industrial standard 19" rack. There are four screw holes on each side of the panel. Figure 2.
2.2 Desktop, Swingarm mounting The FPM-3190 Series can be mounted in other ways. You can place the desktop stand for desktop use or attach it on a swing-arm bracket. 2.2.1 Desktop Stand The desktop stand bracket is attached to the rear of the FPM-3190. Simply detach the small bracket at the top of the monitor by unscrewing the two screws. The lower bracket now becomes the desktop stand bracket. Figure 2.
2.2.2 Swing-ARM Detach the mounting brackets on the rear side, then attach the FPM-3190 series onto the Swing-ARM mount (75mm or 100mm square bracket). Figure 2.
Appendix A Touchscreen Driver Installation • Introduction • Specification • Installation
Appendix A Touchscreen Driver Installation A.1 Introduction The FPM-3190 Series’ optional touchscreen uses an advanced capacitive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class A and Class B standards. A.2 Touchscreen specifications Electrical Input Method: Finger.
MIL-C-675C. Withstands 10,500 grams of force per Balance Beam Scrape Adhesion Mar Tester. MicroScratch tester with 10 micron radius tungsten carbide indenter takes a force of 1.8 Newtons. NEMA Rating: NEMA sealable. Gasketing: Complete water-resistant seal obtainable with polyethylene gasket. Cleaning: Water, isopropyl alcohol, and similar non-abrasive cleaners.
A.3 Installation of Touchscreen Driver The touchscreen into the FPM-3190 Series provides drivers for use with MS-DOS, Windows 95, 98, NT, 2000 and XP. For the detail touchscreen drivers installation procedure, please refer \\FPM-3190TV\Touchscreen\TouchWare563.
Appendix Supported Input Timing Modes B
Appendix B Supported Input Timing Modes B.1 Supported Input Timing Modes The nineteen kinds of timings below are already programmed in this module. The input synchronous signals are automatically recognized. Chroma 2325 Timing No.
Appendix C OSD Operation Keypad
Appendix C OSD Operation Keypad C.1 OSD Operation Keypad The OSD keypad, including six keys and a two color indicator, is designed as the OSD operation interface. The six keypad functions are in Table C-1. Auto Press this button to execute auto adjustment process Sel Press to show the OSD screen or select an item to change its setting ! # To move between items or increase or decrease setting Exit This key has two functions: 1.) To exit from the current setting in OSD function 2.
C.2 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out. Figure C.1: OSD Menu C.2.1 Feature Descriptions 1. Brightness: Press the < and > keys to adjust the brightness. 2. Black level: Press the < and > keys to adjust digital black level control 3.
8. Information: Displays the LCD information. 9. Miscellaneous: Press the < and > to select the Factory reset, OSD timeout, OSD position, dithering, Native mode. 10. Input select: Press the < and > to select the Analog, DVI, Video, Svideo source input. 11. Video: Press the < and > to select Hue, Saturation, H-position, Vposition to adjust 12. YUV color: Press the < and > to select brightness, black level, contrast, saturation, Hue, Flesh tone 13.
C.2.2 FPM-3190TV Input select operation process Default setting for this devise is “Analog Source Input.” If you want to use other signal sources like DVI, Video, S-video. Please refer to the following flow chart.
FPM-3190 User’s Manual 24
