PWR-246E Industrial DC to DC Converter User Manual
Copyright The documentation and the software included with this product are copyrighted 2006 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity FCC Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from humidity. Put this equipment on a reliable surface during installation.
16. AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. The sound pressure level at the operator's position according to IEC 7041:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1.
Contents Chapter 1 Introduction ..................................................... 2 1.1 1.2 1.3 1.4 Chapter Specifications .................................................................... 2 1.1.1 1.1.2 General Specifications ................................................... 2 Output Specifications ..................................................... 2 Connectors......................................................................... 3 Pin Assignments........................................
PWR-246E User Manual viii
CHAPTER Introduction Sections include: • • • • Specifications Connectors Pin Assignments Dimensions 1
Chapter 1 Introduction 1.1 Specifications 1.1.
1.2 Connectors The following connectors are situated on the box of PWR-246E : Plug-In Block 3P Male (ME050-50803) This block connector can be connected via the external plug-in block 3P with flanges Female MC211-F103 connector 12V DC Power Output Cable This cable with 12VDC output will be connected to the FPM series products with 12VDC input 1.3 Pin Assignments 1. GND 2. Vin 3.
1.4 Dimensions Figure 1.
CHAPTER 2 Mounting Methods Sections include: • • • • • • • • FPM-3060G FPM-3120G/3121G FPM-3150G FPM-2150G FPM-3170G FPM-3171G FPM-3190G FPM-3191G
Chapter 2 Mounting Methods 2.1 Mounting to FPM Series Monitors PWR-246E is designed for 12VDC input to FPM products in Advantech. You can mounted in FPM products by using separately location or existing mount hole in the products. 2.1.1 FPM-3060G 2.1.
2.1.3 FPM-3150G 2.1.
2.1.5 FPM-3170G 2.1.
2.1.7 FPM-3190G 2.1.
PWR-246E User Manual 10
