FPM-3170 Series Industrial Flat Panel Monitor with 17" LCD in VGA/Video User Manual
Copyright This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Additional Information and Assistance 1.Visit the Advantech web site at www.advantech.com where you can find the latest information about the product. 2.Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
Table of Contents Contents Chapter Chapter 1 Introduction ..................................................... 2 1.1 1.2 Introduction ....................................................................... 2 Specifications .................................................................... 2 1.3 1.4 1.5 LCD Specifications ........................................................... 3 Connectors......................................................................... 4 Dimensions......................
Appendix A Touchscreen Driver Installation .................. 14 A.1 A.2 Introduction ..................................................................... 14 Touchscreen Specifications............................................. 14 A.3 A.4 Installation of Touchscreen Driver.................................. 15 Configuring PenMount Windows 2000/XP Driver......... 20 A.2.1 A.2.2 A.2.3 A.2.4 A.2.5 A.4.1 A.4.2 A.4.3 Electrical ......................................................................
CHAPTER 1 Introduction This chapter includes: •Introduction •Specifications •LCD Specification •Connectors •Dimensions 1 Chapter 1
Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3170 Series consist of 17" color TFT LCD flat panel monitors built specifically for industrial applications. With the optional touchscreen, FPM-3170 monitors are excellent and user-friendly system control interfaces. The FPM-3170 Series includes the FPM-3170G and FPM-3171GA. FPM-3170G comes standard with Direct-VGA, DVI-D, Video, S-Video ports, which not only can connect to popular PC VGA Cards, but also devices with video output, like cameras.
• Vibration (operating): 5 ~ 17 Hz, double-amplitude displacement 17 ~ 500 Hz, 1.0 G peak to peak • Dimensions: (W x H x D):482 x 354 x 68 mm (19" x 13.9" x 2.7") • Net Weight:12.7 kg (27.9 lb) • Compliance: CE, FCC, BSMI, CCC compliant 1.2.
1.4 Connectors The following connectors are situated on the left hand side of the FPM3170 Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15pin DB-15 connector located on the left side of the system unit. S-Video Port (Mini-DIN 4 pin) (Available for FPM-3170G only) Supports NTSC and PAL. DVI-D Port (Available for FPM-3170G only) Touchscreen Connector (DB-9) (Touchscreen version only) This connector will be present only if a touchscreen is installed.
1.5 Dimensions Cutout Dimensions: 451 x 340 mm (17.8" x 13.4") Figure 1.
Figure 1.
CHAPTER 2 System Setup This chapter includes: •Mounting the Monitor - Wall/Panel/Rack Mounting - Desktop Stand/Swing-ARM Mounting 7 Chapter 2 System Setup
Chapter 2 System Setup 2.1 Mounting the Monitor Monitors of the FPM-3170 series can be placed as you require. The versatility of the FPM-3170 mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting With wall mounting brackets, the FPM-3170 monitors can be mounted directly to a wall. The wall mounting brackets (named Fix brackets in the packing list) can be found in the accessory box. 1. First mount the two brackets on the wall.
2.1.2 Panel Mounting If you need to install the FPM-3170 series on a panel mount, please release the wall mounting brackets by detaching four screws on rear side and fix them on top and bottom sides by screws. Figure 2.3: Panel Mounting (cut out dimension: 451 x 340 mm) Figure 2.
2.1.3 Rack Mounting The FPM-3170G series of monitors can be directly mounted to an industry standard 19" rack. There are four screw holes on each side of the panel. Figure 2.
2.2 Desktop Mounting You can place the desktop stand for desktop use or attach it on a swingarm bracket. 2.2.1 Desktop Stand The desktop stand brackets (named mounting bracket in the packing list) can be found in the accessory box. Figure 2.6: FPM-3170 Mounted on Desktop Stand Attach the fix bracket on the bottom part of the FPM-3170. Then use two screws on each of the desktop mounting brackets. Place one on each side of the fix bracket. Figure 2.
2.3 Swing Arm Mounting Detach the mounting brackets on the rear side, then attach the FPM-3170 series onto the Swing-ARM mount (75 or 100 mm square bracket). Figure 2.
Appendix A Touchscreen Driver Installation •Introduction •Specification •Installation 13 Appendix A Driver Installation
Appendix A Touchscreen Driver Installation A.1 Introduction The FPM-3170 Series’ optional touchscreen uses an advanced 8-wire resistive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class B standards. A.2 Touchscreen Specifications A.2.1 Electrical • Operating Voltage: 2.5 to 5 V DC • Linearity: c1.5% error A.2.2 Optical • Transmittance: 78% A.2.
A.2.5 Chemical Resistance The touch screen surface finish is unaffected by exposure to the following chemicals for a period of one hour at 22..C, 45% relative humidity. • ASTM-F-1598-95. • Tea, Coffee, Ketchup, Mustard, Vinegar, Beer, Coca-Cola, Red Wine, Cooking Oil, Wisk Laundry Detergent, Fantastik All Purpose Cleaner, Joy Dishwashing Liquid, Windex, Formula 409 Cleaner, Clorox Bleach (5.
If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please remove it first. Follow the steps below to install the PenMount Windows 2000/XP driver. 1. When the system first detects the controller board, a screen appears that shows “Unknown Device.” Do not use this hardware wizard. Press Cancel.
2. Insert the PenMount Driver CD-ROM. Go to the Windows 2000XP Driver folder. Click setup.exe. 3. The screen displays the installation wizard for the PenMount software. Click “Next”.
4. A License Agreement appears. Click “I accept…” and “Next” 5. The “Ready to Install the Program” screen appears. Select “Install.
6. The next screen is “Hardware Installation.” Select “Continue Anyway.” 7. The “InstallShield Wizard Completed” appears. Click “Finish.
A.4 Configuring PenMount Windows 2000/XP Driver Upon rebooting, the computer automatically finds the new 9000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, click “Calibrate.” A.4.
NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
FPM-3170 Series User Manual 22
Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration. The blue lines show linearity before calibration and black lines show linearity after calibration.
Draw Tests or demonstrates the PenMount touch screen operation. The display shows touch location. Click Draw to start. Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down. Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down. Click Clear Screen to clear the drawing.
Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor.” Following this sequence and touching each screen is called mapping the touch screens.
4. Touching all screens completes the mapping and the desktop reappears on the monitors. 5. Select a display and execute the ‘Calibration’ function. A message to start calibration appears. Click OK. 6. “Touch this screen to start its calibration” appears on one of the screens. Touch the screen. 7. “Touch the red square” messages appear. Touch the red squares in sequence. 8. Continue calibration for each monitor by clicking Standard Calibration and touching the red squares.
NOTE: 1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors function. Just follow the regular procedure for calibration on each of your desktop monitors. 2. The Rotating function is disabled if you use the Multiple Monitors function. 3. If you change the resolution of display or screen address, you have to redo Map Touch Screens so the system understands where the displays are.
About This panel displays information about the PenMount controller and driver version.
A.4.2 PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities. PenMount Monitor has the following functions. Beep Turns beep on or off. Right Button When you select this function, a mouse icon appears in the right-bottom of the screen. Click this icon to switch between Right and Left Button functions.
A.4.3 PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Please see Chapter 5 for more information.
FPM-3170 Series User Manual 32
Appendix B Supported Input Timing Modes 33
Appendix B Supported Input Timing Modes B.1 Supported Input Timing Modes The nineteen kinds of timings below are already programmed into this module. The input synchronous signals are automatically recognized.
Appendix C OSD Operation Keypad 35
Appendix C OSD Operation C.1 OSD Operation Keypad The OSD keypad, including six keys and a two color indicator, is designed as the OSD operation interface. The six keypad functions are in Table C-1. Auto Press this button to execute auto adjustment process Sel Press to show the OSD screen or select an item to change its setting ! # To move between items or increase or decrease setting Exit This key has two functions: 1.) To exit from the current setting in OSD function 2.
C.2 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out.
FPM-3170 Series User Manual 38
