FPM-3150TVE Series Flat Panel Monitor with 15" Color TFT/LCD Display enchanced version User's Manual
Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before installing your equipment, make sure that the following materials have been received: • FPM-3150TVE Series flat panel monitor • Accessory pack, including: - AC/DC adapter (optional) - Power Chord (optional) - Video signal cable - Component bag - RS-232 cable - Screw bag - Touchscreen driver disks for Win95/98/NT/2000 (FPM-3150TVE-T only) - FPM-3150TVE Series User's Manual If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
CHAPTER Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Power Consumption • Connectors • Dimensions 1
1.1 Introduction Advantech's FPM-3150TVE Series is a 15" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touchscreen, the FPM-3150TVE Series is an excellent and user-friendly system control interface. In addition to its usual application as an LCD panel monitor, the FPM3150TVE comes standard with direct VGA control signal input (same as the FPM-3150TV), making it compatible with Industrial PCs and Workstations.
Touchscreen (Optional) • Type: 8 wire, analog resistive • Resolution: continuous • Light transmission: 75% (surface meets ASTM-D-3363-92A Standard, tabler abrasion test) • Operating Pressure: 30 ~ 45 gram for stylus pen, contact bounce < 10 ms • Controller: RS-232 interface • Power Consumption: +5 V @ 200 mA • OS support: Windows 95/98, Windows NT/2000, MS-DOS • Life span: 100 million touches 1.3 LCD Specification • • • • • • • • • • • Display type: XGA TFT LCD Display size: 15" Max. colors: 16.
1.5 Connectors The following connectors are situated on the left hand side of the FPM-3150 Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15-pin DB-15 connector locatd on the left side of the system unit. Touchscreen Connector (DB-9) (optional) This connector will be present only if a touchscreen is installed. It must be connected to the RS-232 port of the PC. The touchscreen cable is included with all orders which include the touchscreen option.
FPM-3150TVE (15") Unit: mm 1.
6 FPM-3150TVE User's Manual
CHAPTER 2 System Setup • Mounting the Monitor - Wall/Panel/Rack Mounting - Desktop Stand/Swing-ARM Mounting
2.1 Mounting the Monitor The FPM-3150 Series can be placed as you require. The versatility of the FPM-3150 mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting Thanks to wall brackets, the FPM-3150 can be mounted directly to a wall. If you need to install the FPM-3150 in different ways, release the mounting brackets by detaching four screws on the rear side.
2.1.2 Panel Mounting If you need to install the FPM-3150 series on a panel mount, please release the mounting brackets by detaching four screws on rear side and fix them on up and bottom side by screws.
2.1.3 Rack Mounting If you need to install the FPM-3150TVE on a rack, you must order the rack mount kit (4 pieces of brackets) for the FPM-3150TVE (Part Number is FPM-3150Rack-MT). Assemble the rack mount brackets on either side of FPM-3150TVE with 12 screws, then affix the monitor on the rack. Figure 2.
2.2 Desktop, Swing-ARM for FPM-3150TVE The FPM-3150 Series can be mounted in other ways. You can place the desktop stand for desktop use or attach it on a swing-arm bracket. 2.2.1 Desktop Stand The desktop stand bracket is attached to the rear of the FPM-3150. Simply detach the small bracket at the top of the monitor by unscrewing the two screws. The lower bracket now becomes the desktop stand bracket. Figure 2.
2.2.2 Swing-ARM Detach the mounting brackets on the rear side, then attach the FPM3150 series onto the Swing-ARM mount (75mm or 100mm square bracket). Figure 2.
APPENDIX A Touchscreen Driver Installation • Introduction • Specification • Installation - for Windows 95/98 - for Windows NT/2000
A.1 Introduction The FPM-3150 Series’ optional touchscreen uses an advanced 8-wire resistive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class A and Class B standards. A.2 Touchscreen Specification Electrical • Contact bounce: < 10 ms • Operating voltage: 5 V (typical) • Contact current: 20 mA (max.
Optical • Visible light transmission: 75% (typical) • Reflection: > 25% @ 550 nm Sensor board • Chemical strengthened glass meets “4H” hardness standard (Test condition: ASTM D3363-92A) Ball drop test • Touchscreen can withstand a 225 g steel ball dropped from a height of 660 mm, without breaking Environmental • Operating pressure: 30 ~ 45 grams for finger; 10 grams for stylus pen • Operating temperature: 0 ~ 50° C (humidity 20 ~ 90% RH) • Storage temperature: -25 ~ 70° C (humidity 20 ~ 95% RH) A.
A.3.1 Installation for Windows 95/98 1. A. Select Start menu and then click Run B. Type D:\fpm\touchdrv\penmount\win9xv3.3\setup.exe C. Press OK D. Follow the instructions for the setup process 2. A. Click the Detect button B.
3. A. After the system reboots, click Start, Programs, PenMount Utilities, PenMount Control Panel B. Select the Calibrate tab C. Click the Calibrations button on the right 4. A. Use a soft stylus to press the little red dot located above the finger icon B.
5. Press OK A.3.2 Installation for Windows NT 1. A. Select Start menu and then click Run B. Type D:\fpm\touchdrv\penmount\winnt-ver3.11\setup.exe C. Press OK D.
2. A. Click the Detect button B. Press OK and the system will reboot 3. A. After the system reboots, click Start, Programs, PenMount Utilities, PenMount Control Panel B. Select the Calibrate tab C.
4. A. Use a soft stylus to press the little red dot located above the finger icon B. Repeat the process according to the sequence: top, right, bottom, and left 5.
A.3.3 Installation for Windows 2000 1. A. Select Start menu and then click Run B. Type D:\fpm\touchdrv\penmount\win2000v1.0\setup.exe C. Press OK D. Follow the instructions for the setup process 2. A. Click the Detect button B.
3. A. After the system reboots, click Start, Programs, PenMount Utilities, PenMount Control Panel B. Select the Calibrate tab C. Click the Calibrations button on the right 4. A. Use a soft stylus to press the little red dot located above the finger icon B.
5.
A.3.4 Installation for DOS A.3.4.1 Using HMI CD Driver to install PenMount software driver. A.Insert the driver CD toCD-ROM drive. B. Type "D:\fpm\touchdrv\penmount\win31&dos\install" C. A pop-up window will display "Salt International Corp. PenMount Install Utilities. Press ENTER key to allow PenMount install the drivers to drive C or use keyboard to key-in the hard disk drive that you plan to install the driver." Press ENTER. D.The pop-up window will ask "Do you want to modify your Autoexec.
If you do not need to detect IRQ5 and IRQ9, the command is: C:\PENMOUNT\PMDETECT -N5 -N9 A.3.4.3 Do Calibration A.To adjust touch screen mapping properly for the display, use PM.BAT (C:\PENMOUNT\PM ) tocalibration. B. Choose “1” DO CALIBRATION (adjust screen mapping). C. The message on the pop up window asks you to select video mode number. Select by keyboard to start the calibration, touch the uppercenter point, then right-center point, bottom-center point and leftcenter point in sequence.
“PENMOUNT” directory can also be applied. Now, the PenMount DOS driver is installed. A.3.4.6 PenMount DOS driver functions There are several functions in the PenMount DOS driver. The user is able to change the settings of the following utilities: ??Show Current Setting A.The current setting data could be found from PM.BAT file. B. The procedure to get the status is C:\PENMOUNT\PM C. Choose “2” SHOW CURRENT SETTINGS ??Bep Sound Onor Off A.Beep sound is able to set ON or OFF with parameter. B.
APPENDIX B Standard Timing Set Serial Data for Expansion
B.1 Setting serial data for expansion The fourteen kinds of timings below are already programmed in this module. The input synchronous signals are automatically recognized. 28 Note 1: Even if the preset timing is entered, a little adjustment of the functions such as Horizontal period, CLK-delay and display position, are required. The adjusted values are memorized in every preset number.
Appendix B Standard Timing 29
30 FPM-3150 Series User's Manual
APPENDIX C • OSD Selection • Keypad Interface • OSD Function
C.1 Keypad Interface The keypad interface provides driver for a dual color LED for status indication. PS, The green light means that the COMMON board detects the input signal and ends output signal to LCD panel .
C.2 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out.
34 FPM-3150 Series User's Manual
