FPM-3120TV Series Flat Panel Monitor with 12" Color TFT/LCD Display User's Manual
Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before installing your equipment, make sure that the following materials have been received: • FPM-3120TV Series flat panel monitor • Accessory pack, including: - AC/DC adapter - Power Chord - Video signal cable, 1.8m - Keyboard/mouse Y cable - AC/DC power adapter bracket - Hook wall-mounted bracket (in FPM-3120TV) - Four fixed panel-mounted bracket - Mounting bracket (in FPM-3120TV) - RS-232 cable, 1.8m (FPM-3120TV-T only) - Keyboard/mouse 1.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
CHAPTER Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Power Consumption • Connectors • Dimensions 1
1.1 Introduction Advantech's FPM-3120TV Series is a 12" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touchscreen, the FPM-3120TV Series is an excellent and user-friendly system control interface. In addition to its usual application as an LCD panel monitor, the FPM-3120TV comes standard with direct VGA control signal input making it compatible with Industrial PCs and Workstations.
Touchscreen (Optional) • Type: 8 wire, analog resistive • Resolution: continuous • Light transmission: 75% (surface meets ASTM-D-3363-92A Standard, tabler abrasion test) • Controller: RS-232 interface • Power Consumption: +5 V @ 200 mA • OS support: Windows 95/98, Windows NT/2000, MS-DOS • Life span: 100 million touches 1.3 LCD Specification • • • • • • • • • • Display type: SVGA TFT LCD Display size: 12.1" Max. colors: 262 K Max.
1.5 Connectors The following connectors are situated on the buttom of the FPM-3120 Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15-pin DB-15 connector locatd on the left side of the system unit. Keyboard & mouse Connector (PS/2) There are two PS/2 connectors which can ne connected to keyboard or mouse. Touchscreen Connector (DB-9) (optional) This connector will be present only if a touchscreen is installed.
1.5.1 PS/2 connectors The FPM-3120TV provides two PS/2 connectors in the buttom side. Please follow the steps to connect the keyboard /mouse cable. 1. Connect 1.8m keyboard/mouse cable to one of the PS/2 port. 2. Connect other side of Keyboard/mouse 1.8m cable to PC 3. Connect Y cable to another PS/2 port in FPM-3120TV Note: You MUST select one PS/2 port to connect 1.8m cable to PC. Keyboard/mouse 1.
FPM-3120TV (12") 6 Cut out dimension : 303 X229 mm (11.93" X 9.02") Unit: mm 1.
CHAPTER 2 System Setup • Mounting the Monitor - Wall/Panel mounting - Desktop Stand/Swing-ARM Mounting
2.1 Mounting the Monitor The FPM-3120 Series can be placed as you require. The versatility of the FPM-3120 mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting Please follow the steps to install FPM-3120TV in the wall. 1. Screw the wall-mount bracket in the wall. 2. Put the FPM-3120TV in the bracket. 3.
2.1.2 Panel Mounting If you need to install the FPM-3120 series on a panel mount, please release the mounting brackets by detaching screws on rear side and fix them on up and bottom side by screws.
2.2 Desktop, Swing-ARM for FPM-3120TV The FPM-3120 Series can be mounted in other ways. You can place the desktop stand for desktop use or attach it on a swing-arm bracket. 2.2.1 Desktop Stand The desktop stand bracket is attached to the rear of the FPM-3120. Simply detach the small bracket at the rear side of the monitor by screwing the two screws. The bracket now becomes the desktop stand bracket. Figure 2.
2.2.2 Swing-ARM 75 100 Detach the mounting brackets on the rear side, then attach the FPM3120 series onto the Swing-ARM mount. Figure 2.
2.2.3 Power adapter The power adapter bracket is attached to the rear of the FPM-3120. Simply detach the small bracket at the rear side of the monitor by screwing the four screws.
Note: If you find that the brightness of LCD is dark, please follow the steps to adjust it. 1. Find the OSD in the rear side of FPM-3120TV 2. Press two buttons, " " & " " , at the same time. 3. The LCD will reset and get brighter.
APPENDIX A Standard Timing Set Serial Data for Expansion
Appendix A Display Timing Mode and OSD A.1 Supported Input Timing Modes The nineteen kinds of timings below are already programmed in this module. The input synchronous signals are automatically recognized. Resloution Vertical Frequencies 60 Hz 640 x 480 Yes 800 x 600 Yes 70 Hz 72 Hz 75 Hz Yes Yes Yes Table A.1: Supported Input Formats Note 1: Even if the preset timing is entered, a little adjustment of the functions such as Horizontal period, CLK-delay and display position, are required.
APPENDIX B • OSD Selection • Keypad Interface • OSD Function
B.1 Keypad Interface The keypad interface provides driver for a dual color LED for status indication. AUTO Press this button to execute auto adjustment process. SEL Presses to show the OSD screen or select an item for changing its setting. To move between items or increase item setting. EXIT To close the selected item or the whole OSD screen. ON/OFF Turn the display backlight ON and OFF. PS, The green light means that the COMMON board detects the input signal and ends output signal to LCD panel .
B.2 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out.
