FPM-3120G Series Flat Panel Monitor with 12.
Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before installing your equipment, make sure that the following materials have been received: • FPM-3120G Series flat panel monitor • Accessory pack, including: - AC/DC adapter - AC/DC power adapter bracket - Video signal cable, 1.8m - Fixed panel-mounted bracket x 8 pcs - Screw Bags (M4x25 mm screws x 8 pcs) - DC in Power Cord bracket x 1 piece - RS-232 cable, 1.8m - Driver/manual CD-ROM If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT. The sound pressure level at the operator's position according to IEC 7041:1982 is no more than 70dB(A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprüfen: a - Netzkabel oder Netzstecker sind beschädigt. b - Flüssigkeit ist in das Gerät eingedrungen. c - Das Gerät war Feuchtigkeit ausgesetzt. d - Wenn das Gerät nicht der Bedienungsanleitung entsprech end funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
Contents Chapter 1 Introduction ..................................................... 2 1.1 1.2 1.3 1.4 1.5 1.6 Chapter Introduction ....................................................................... 2 Specifications .................................................................... 3 LCD Specifications ........................................................... 4 Power Adapter Specifications ........................................... 4 Connectors..................................................
FPM-3120G Series User Manual x
CHAPTER 1 2 Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Power Consumption • Connectors • Dimensions
Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3120G series consists of 12.1" color TFT LCD flat panel monitors built specifically for industrial applications. With the optional touchscreen, the FPM-3120G-R series offers user-friendly system control interfaces. In addition to its usual application as an LCD panel monitor, the FPM3120G-X Series comes standard with Direct VGA control signal input, making it compatible with industrial PCs and workstations.
1.2 Specifications General • Construction: Heavy-duty stainless steel chassis • Front Panel: Aluminum, NEMA4/IP65 compliant • Control: OSD (On Screen Display) control pad on front side • Mounting: Panel, wallmount, desktop or VESA Arm • Dimensions (W x H x D): 312x244x44.6mm (12.3"x9.6"x1.8") • Panel Mount Cut out Dimension (WxH): 304x230mm (11.9"x9.0") • Weight: 3.0 kg (6.6 lb) • Vibration (operating): 5 ~ 500 Hz, Random, 1 Grms • CE, FCC, BSMI, CCC certified • Power Consumption: +12V +/- 10% @ 3.
1.3 LCD Specifications • Display Type: TFT LCD with XGA for FPM-3121G series, or SVGA for FPM-3120G series. • Display Size: 12.1" • Max. Colors: 262 k • Max.
1.5 Connectors The following connectors are on the bottom of the FPM-3120G Series: VGA Port (DB15) This DB-15 connector can be connected to the system via the external 15pin DB-15 connector locatd on the left side of the system unit. RS-232 Touchscreen Connector (DB9) (with FPM-3120G-R & FPM-3121G-R) This connector will only be present if a touchscreen is installed. It must be connected to the RS-232 port of the PC. The touchscreen cable is included with all orders that include the touchscreen option.
1.6 Dimensions Figure 1.
CHAPTER 2 2 System Setup • Mounting the Monitor • Wall / Panel Mounting • Desktop / Swing-Arm Mounting
Chapter 2 System Setup 2.1 Mounting FPM-3120G Series Monitors in the FPM-3120G series can be flexibly mounted. The versatility of the FPM-3120G series mounts enable them to be mounted on your desk or almost anywhere else. 2.1.1 Wall Mounting Please refer to figure 2.1 and follow the steps below to install FPM3120G series on a wall. The wall mounting kit is optional. (P/N:FPM-2150G-SMKE) 1. Screw the hook and wall-mounted brackets on the wall. 2. Place the FPM-3120G series in the bracket.
2.1.2 Panel Mounting Refer to figure 2.2 and follow the instructions below to install in a panel. 1. Insert the FPM-3120G series’ into the cutout hole of the panel. (The dimensions of the cutout is 304x230mm (11.9"x9.0")) 2. Place eight panel-mounting brackets on FPM-3120G series’ (2 on the top, 2 on the bottom, 2 on the left, and 2 on the right). 3. Fasten the eight panel-mounting brackets with screws. 4.
2.2 Desktop, Swing-ARM for FPM-3120G Series The FPM-3120G series’ monitors can also be mounted in other ways. You can use the desktop stand for desktop use or attach it on a swing-arm bracket. 2.2.1 Desktop Stand Refer to figure 2.4. The desktop stand bracket is attached to the rear of FPM-3120G series’. Simply attach the small bracket at the rear side of the monitor by screwing the two screws. The bracket now becomes the desktop stand bracket. The desktop stand kit is optional. (FPM-2150G-SMKE) Figure 2.
2.2.2 VESA ARM Mounting FPM-3120G series has been designed with support for the VESA arm standard. Refer to figure 2.5. Figure 2.
2.2.3 Power Adapter The power adapter bracket can be attached to the rear of FPM-3120G series. Attach the bracket at the rear side of the monitor by screwing the four screws. The DC terminal of the AC/DC adapter can be locked on the rear case by the DC in Power Cord bracket. .
A APPENDIX 2 Display Timing Mode and OSD
Appendix A Display Timing Mode & OSD A.1 Supported Input Timing Modes The different frequencies below are already programmed in this module, and the synchronous signal inputs are automatically recognized. Table A.
A.2 Keypad Interface AUTO Press this button to execute auto-adjustment process. SEL Press to show the OSD screen or select an item to change its setting. Press to move between items or increase/decrease item setting. Press both buttons simultanously to lock/unlock the current settings. EXIT Press to close the selected item or the whole OSD screen. ON/OFF Press the ON/OFF button to turn FPM-3120G-UA’s backlight on and off. When power is off, the power indicator will be blinking. A.
A.4 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out.
APPENDIX B 2 Touchscreen This appendix contains information on the touchscreen, its installation and configuration.
Appendix B Touchscreen B.1 Introduction The FPM-3120G Series’ optional touchscreen uses advanced 3M™ 8wire resistive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class B standards. B.2 Touchscreen Specifications Electrical • Contact bounce: < 10 ms • Operating voltage: 5 V (typical) • Sheet Resistance: 350 +/- 22% per Square. • Linearity: <1.
Optical • Visible light transmission: 75% typical (>74% @ 550 nm test) • Clarity: Clear Finish - 25%, Antiglare Finish - 15% Sensor board • Chemical strengthened glass with 4 H hardness standard. (Test condition: ASTM D3363-92A) Ball drop test • Able to bear a 225 g steel ball dropped from 660 mm elevation without breaking Environmental Specifications • Operating Temperature Range: -20° C ~ +50° C, 2 weeks at 50° C / 90% RH. • Storage Temperature High: +70° C, 240 hours at ambient humidity.
Before installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system installed and running on your computer. If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please remove it first. Follow the steps below to install the PenMount Windows 2000/XP driver. 1. When the system first detects the controller board, a screen appears that shows “Unknown Device.” Do not use this hardware wizard. Press Cancel. 2.
3. The screen displays the installation wizard for the PenMount software. Click “Next”.
4. A License Agreement appears. Click “I accept…” and “Next” 5. The “Ready to Install the Program” screen appears. Select “Install.
6. The next screen is “Hardware Installation.” Select “Continue Anyway.” 7. The “InstallShield Wizard Completed” appears. Click “Finish.
B.4 Configuring PenMount Windows 2000/XP Driver Upon rebooting, the computer automatically finds the new 9000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, click “Calibrate.” B.4.
NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
FPM-3120G Series User Manual 26
Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration. The blue lines show linearity before calibration and black lines show linearity after calibration.
Draw Tests or demonstrates the PenMount touch screen operation. The display shows touch location. Click Draw to start. Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down. Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down. Click Clear Screen to clear the drawing.
Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor.” Following this sequence and touching each screen is called mapping the touch screens.
4. Touching all screens completes the mapping and the desktop reappears on the monitors. 5. Select a display and execute the ‘Calibration’ function. A message to start calibration appears. Click OK. 6. “Touch this screen to start its calibration” appears on one of the screens. Touch the screen. 7. “Touch the red square” messages appear. Touch the red squares in sequence. 8. Continue calibration for each monitor by clicking Standard Calibration and touching the red squares.
NOTE: 1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors function. Just follow the regular procedure for calibration on each of your desktop monitors. 2. The Rotating function is disabled if you use the Multiple Monitors function. 3. If you change the resolution of display or screen address, you have to redo Map Touch Screens so the system understands where the displays are.
About This panel displays information about the PenMount controller and driver version.
B.4.2 PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities. PenMount Monitor has the following functions. Beep Turns beep on or off. Right Button When you select this function, a mouse icon appears in the right-bottom of the screen. Click this icon to switch between Right and Left Button functions.
B.4.3 PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Please see Chapter 5 for more information.
B.5 Uninstall the PenMount Windows 2000/XP driver 1. Exit the PenMount monitor (PM) in the menu bar. 2. Go to Settings, then Control Panel, and then click Add/Remove program. Select PenMount DMC9000 and click the Add/Remove button. 3. Select PenMount DMC9000 and DMC9100. Click the Remove button. 4. Select ‘Yes’ and “Close” to remove the PenMount Windows 2000/ XP driver, and reboot the system.
