User Manual EPD Control Board EPD-132 Wireless ePaper Display Solution
Copyright The documentation and the software included with this product are copyrighted 2019 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity FCC Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
LABEL OF THE END PRODUCT: Host Model Name EPD-132R2 The final end product must be labeled in a visible area with the following " FCC ID: M82-EPD-132-092 ". If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. 1 EPD-132 EPD control board & 13.3" EPD Part No. Description EPD-132B1AG-NSD01 13.3" Black/White ePaper Wi-Fi / BT display module solution in 2.4G EPD-132R1AG-NSD01 13.3" Red/Black/White ePaper Wi-Fi / BT display module solution in 2.
EPD-132R1AG-NSD11 EPD-132R1AG-NSD01 for 50 pcs solution kit EPD-132R1AG-NSD21 EPD-132R1AG-NSD01 for 100 pcs solution kit EPD-132R1AG-NSD31 EPD-132R1AG-NSD01 for 500 pcs solution kit EPD-132R1AG-NSD41 EPD-132R1AG-NSD01 for 1000 pcs solution kit EPD-132B1AG-NSD11 EPD-132B1AG-NSD01 for 50 pcs solution kit EPD-132B1AG-NSD21 EPD-132B1AG-NSD01 for 100 pcs solution kit EPD-132B1AG-NSD31 EPD-132B1AG-NSD01 for 500 pcs solution kit EPD-132B1AG-NSD41 EPD-132B1AG-NSD01 for 1000 pcs solution kit Ordering
Safety Instructions 1. 2. 3. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Consignes de Sécurité 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Lisez attentivement ces instructions de sécurité. Conservez ce manuel de l'utilisateur pour référence ultérieure. Débranchez cet appareil de toute prise secteur avant le nettoyage Utilisez un chiffon humide. N'utilisez pas de détergents liquides ni en spray pour le nettoyage Pour les équipements enfichables, la prise de courant doit être située à proximité de l'équipement et doit être facilement accessible.
Contents Chapter 1 Introduction..........................................1 1.1 1.2 Introduction ...............................................................................................2 Specifications............................................................................................2 Figure 1.1 Block Diagram............................................................4 System implementation.............................................................................5 1.3.
Chapter 4 EPD-132 in ePaper Manager ............33 4.1 EPD-132 with ePaper Manager Solution................................................ 34 Table 4.1: ePaper manager main feature list............................ 34 Preparation ............................................................................................. 35 4.2.1 Hardware Component List.......................................................... 35 4.2.2 Software Component List ...........................................................
Chapter 1 Introduction 1
1.1 Introduction The EPD-132 is a module which supports the ultra-low power 2.4GHz RF wireless protocol integrated with the 13.3" R/B/W & B/W EPD in an ARM Cortex-M4 processor. Users may use this kit to experience how wireless modules deliver images to ePaper and how e-Paper displays images. Users control our host mcu BM22 through the Advantech ED22 development board. The main features of EPD-132 is: ARM Cortex-M4 Core Processor Support IEEE 802.11b/g/n + Bluetooth 4.1 standard 13.
4pin Pin Header FFC Connector1 (Alert) LED/button daughter board FFC Connector2 (FFC_GPIO) 10 port GPIO for system expansion UART debug port Switch Factory mode setting Micro USB (CN2) USB to TCON (Timing Controller) Interface for data to EPD EPD connec39P for 13.3" (R/B/W orB/W) & 9.7" EPD (R/B/W) tor Micro USB (CN2) up to 0.9A/4.5 W in USB3.
Figure 1.
EPD device can be applied to different applications and the system integrator can control the RESTful API for different scenarios. 1.3.1 Advantech EPD-132 & ePaper Manager Solution 5 EPD-132 Board User Manual Introduction Wireless EPD System consists of ePaper Manager, Gateway, Router and EPD device. The ePaper Manager provides Web GUI to management the wireless EPD device. The Gateway/embedded computer are responsible for communication between ePaper Manager and EPD device.
EPD-132 Board User Manual 6
Chapter 2 EPD Hardware Specification 2
This section provides board level PCBA and Panel mechanical size. EPD-132 PCBA with following spec. PCBA: 108 x 122 x 3.9 mm PCB thickness: 3 mm ± 10% Module input voltage: 5V DC-in Connector current rating: 0.5A / Power contact Figure 2.1 MODULE OUTLINE: 108 x 122 x 3.9 mm 13.3" EPD (PN:968AD00147/968AD00388) with following spec. Panel Size: 285.8 x 213.
Chapter 2 Note! E Ink Recommend condition for storage: Temperature: 20 +-10 °C Humidity: 60% RH+-10%RH, Non-condensing Note! If the panel module has been put in low temperatured between 0~-25 °C for a while, we recommend to leave it between 20 to 30 °C for 4 days before assembly. 9 EPD-132 Board User Manual EPD Hardware Specification Figure 2.
2.1 Board level I/O Table 2.
Chapter 2 2.1.
Table 2.2: CN2 PIN PIN_NAME 1 +V5 2 USB_D- 3 USB_D+ 4 GND 5 GND 2.1.
Chapter 2 EPD Hardware Specification Table 2.3: CN3 PIN PIN_NAME 1 +V5 2 N/A 3 N/A 4 N/A 5 GND 2.1.
Table 2.
Chapter 2 2.1.4 CN9 EPD Hardware Specification Table 2.
2.1.
PIN_NAME PIN PIN_NAME 1 +VSL (Negative power supply source driver) 2 +VSH_O (Positive power supply source driver) 3 GND 4 +V3.3_EPD (3.
2.1.6 Daughter Board Connector Table 2.
Chapter 2 2.1.6.1 Daughter Board PIN PIN_NAME PIN PIN_NAME 1 3 SW1 GND 2 4 LED_1 : Green NC 5 LED_2: Red 6 SW3 7 NC 8 NC 9 NC 10 +VDD SW1 Un-mount, SW3 as below Table 2.9: SWTEST PIN PIN_NAME PIN PIN_NAME 1 +VDD 2 SW3 3 GND 4 GND 19 EPD-132 Board User Manual EPD Hardware Specification Table 2.
Table 2.10: LED PIN PIN_NAME PIN PIN_NAME 1 +VDD 2 +VDD 3 LED_1- 4 LED_2- 2.1.
Chapter 2 PIN PIN_NAME PIN PIN_NAME 1 +V3.3 2 GPIO_0 (default LOW) 3 GPIO_1 (default LOW) 4 GPIO_2 (default LOW) 5 GPIO_3 (default LOW) 6 GPIO_4 (default LOW) 7 GPIO_5 (default LOW) 8 GPIO_6 (default LOW) 9 GPIO_7 (default LOW) 10 GND GPIO Voltage level is 3.3V 21 EPD-132 Board User Manual EPD Hardware Specification Table 2.
2.1.8 DEBUG Table 2.12: FFC_GPIO PIN PIN_NAME PIN PIN_NAME 1 UART1_TX 2 UART1_RX 3 GND 4 JTAG_TDI 5 JTAG_TDO 6 JTAG_TCK 7 JTAG_TMS 8 JTAG_TRST 9 BOOT_0 10 +V3.
Chapter 2 1. TDI (Test Data In) 2. TDO (Test Data Out) 3. TCK (Test Clock) 4. TMS (Test Mode Select) 5. TRST (Test Reset) optional. 2.1.9 SWTEST EPD Hardware Specification Table 2.
2.1.10 PWR_ON1 Table 2.
1) Connected EPD FPC to mainboard The FPC from the ePaper display Blend the FPC carefully to the control board direction Insert the FPC into the connector on control board 25 EPD-132 Board User Manual EPD Hardware Specification Release the rotary latch of the connector on the control board Chapter 2 2.1.
After connecting firmly, lock the rotary latch. Check if the connection is correct and tight.
The daughter board: 9696053RS00 can work with EPD-132. 2.2.1 Button behaviors 1. 2. Status Action Result When LED2 is on Press button for 0.5 sec and release button 1 2 Turn off LED2 When LED2 is off Change to next page image When LED2 is off Step 1.LED2 flash (0.5 sec toggle LED2) after hold 5 sec. Step 2. LED2 on and hold 10 sec Step 3. LED2 off and then release SW3 keys Final result->Reset to default and reboot Press button for 10 sec 2.2.2 LED behaviors 1. 2.
EPD-132 Board User Manual 28
Chapter 3 EPD Network Architecture and Software features 3
3.1 System Topology Architecture 3.1.1 System environment No Device1 OS version 1 ARK 2250L/ePaper manager WIN7, WIN10 (2019,Q3) 64 bit, Professional 2 WISE Gateway: WISE3610W OpenWRT R1.2.11 SW version: 3610WOIV0101-WifiEPD 6 EPD-132: Cypress BM22 ThreadX v5.6 , SDK 4.1.8 V1.0.0 3.2 System Specification 1. 2. Each WISE-3610W gateway can organized an isolated network and be a Wi-Fi AP as well. Each WISE-3610W can support up to 100 EPD devices 3.2.
Receive commands from ePaper manager and execute. Control EPD-132 through commands from ePaper manager. EPD-132 wireless can connect to WISE-3610W directly. EPD-132 wireless connects to Intranet AP, then WISE-3610W acts as a gateway to control EPD-132 Supports MQTT broker Server . 1. 2. 3. 4. Supports BLE re-config : if device keeps failing to join, the device will enable BLE for new SSID. Supports emergency status report after join router. E.g.
EPD-132 Board User Manual 32
Chapter 4 4 EPD-132 in ePaper Manager
4.1 EPD-132 with ePaper Manager Solution Previously, we have go through EPD-132 function as an end device. To build up a solution, we need a gateway to connect to our CMS: ePaper manager. Indeed, ePaper Manager provides complete solution to help you import tag data, design tag templates and manage tags easily. This user manual will show you how to build a total solution system.
4.2.1 Hardware Component List 1. 2. Advantech Embedded Computer: ARK-2250L Advantech IoT Gateway: WISE-3610W & Advantech EPD devices. 4.2.2 Software Component List Window7 Professional version for ARK2250L ePaper Manager Installation & License on ARK2250L 500 connection License on ARK2250L. Recommend Browser: Chrome version 75.0.3770.100 (official version) (64-bit) Recommend FTP Server: FileZilla Server version 0.9.60 beta 4.2.
1. First, you will need to install ePaper manager on ARK-2250L. ePaper Manager Installation Double click the EPD ServerSetup_1.0.0.exe file to start installation process on the server-side computer. Follow the instructions in the setup wizard.
37 EPD-132 Board User Manual EPD-132 in ePaper Manager Please click the next button if you no need to change the default installation path. Chapter 4 Windows hotfix of KB2999266 is required to run this software. Please download one from Microsoft website and execute it. (https://www.microsoft.com/zh-TW/download/ confirmation.aspx?id=49093). Microsoft Visual C++ 2015 Redistributable Update 3 (https://www.microsoft.com/en-us/download/details.
Please check your public IP or domain name and fill it in. Please change the port number if need.
39 EPD-132 Board User Manual EPD-132 in ePaper Manager Please fill in the password and confirm password for MongoDB database. Chapter 4 Please fill in the password and confirm password for PostgreSQL database.
Please fill in the password and confirm password for root administrator to login the server. Please click the install button to start installation.
Chapter 4 installing... EPD-132 in ePaper Manager Please allow to access the installation of erl.exe.
Please allow to access the installation of epmd.exe. Click the Finish button to exit the Setup Wizard. 2. You will get a register key from our sales package. You will need to enable the key after installation of ePaper manager.
Chapter 4 EPD-132 in ePaper Manager EPD-132 Board User Manual 43
4.2.3.1 How to configure your FTP server Before you start transmitting the image to the Electronic Paper Display (EPD) or offering Firmware upgrades, you need to setup ARK2250L as an FTP server. Click the startup icon to launch Filezilla. 1. Start configuring your FTP server. 2. Add user account.
Chapter 4 EPD-132 in ePaper Manager EPD-132 Board User Manual 45
3. Add password for user. 4. Add the shared folders and set the property of the directories and files. Add the FTP Server to OTA Storage. You should make shure that the shared folders are available.
6. Make sure to allow FileZilla Server and FileZilla Server Interface to pass the Windows firewall. 47 EPD-132 Board User Manual EPD-132 in ePaper Manager Open Windows firewall setting and click allow a program or feature through Windows firewall. Chapter 4 5.
4.2.3.2 How to configure your FTP server on ePaper manager 1. Click Storage button to add a FTP storage for OTA and image delivery. 2. Click Add (+) button on the left-upper corner. Select the FTP option. 3. Finish the configuration form and click Confirm.
EPD-132 in ePaper Manager 5. Open up the FTP port of the firewall in the OS. 49 Chapter 4 Storage Name: OTA Security: NONE Domain: [Your Server IP] Port: 21 Account Name: [Your FTP account] Password: [Your FTP password] Root Path: [Your root path] 4. You will see an item in the Storage Management table.
4.2.4 WISE-3610W Setup and Connect to ARK with ePaper Manager After completing the ePaper manager installation, start configuring the Gateway: WISE-3610W. 1. Power on WISE-3610W. 2. Open WISE-3610W management web page: Open a web browser (Chrome is suggested) and enter the IP Address http://192.168.1.1 or http://advantech.local/ 3. Login: The default user name and password are root and ePaper. Click the Login button to open the web-based configuration page. 4. Build networking connection.
Ethernet WAN Backhaul Connection: Connect an Ethernet cable to exiting backhaul router and ISP cable modem or Internet service provider xDSL / FTTx modem. Select WAN for NorthBond backhaul connection and choose Protocol > DHCP Client Chapter 4 5.
6. Setup the ePaper management server IP as shown below. 4.2.5 EPD-132 Setup and Connect to ARK with ePaper Manager This explains how the router joins with the WISE-3610W (gateway). Users can understand what performance can be reached using our specification. The user can also change some parameters to fit their requirements.
2. Default WISE-3610W setting: a. SSID: ADV-ePaper Password: ePaperePaper b. WISE-3610w login as shown below (root/ePaper) Chapter 4 1. EPD-132 in ePaper Manager 3. 4. Power on EPD-132 a. Plug the Micro USB to provide the power. EPD-132 join the network with SSID: a. Setup the SSID to join the network with APP in one device, refer to Chapter 4.3.
Note! 1. 2. 3. 4. 5. The default SSID on WISE-3610W & EPD-132 will be the following: SSID: ADV-ePaper, Password: ePaperePaper Once WISE-3610W & EPD-132 powers on with the default SSID/ Password setting, EPD-132 will connect to WISE-3610W. EPD-132 will set the default Agent IP according to the Domain from gateway after connection. EPD-132 may have changed the default SSID/Password in some cases and lost the connection with the gateway.
Note! You need to remove bluetooth pairing with "WiFiInt" from bluetooth setting when you can not connect to a device. 55 EPD-132 Board User Manual EPD-132 in ePaper Manager Step 3: If the connection is successful, you can see the picture below. Press the "CUSTOM SERVICE" button. Chapter 4 Step 2: Pull down the screen to rescan devices and it will list nearby BLE devices. Find the "WiFiInt" device and press the CONNECT button.
Step 4: Find the UUID: ACA0EF7C-EEAA-48AD-9508-19A6F6B356 for SSID characteristic. Step 5: Find the UUID: 40B7DE33-93E4-4C8B-A876-D833B415A6CE for Password characteristics then procedure as Step4.
4.2.6 Setup the Batch File WISE-3610W Installer In EPD setting, users can add EPD node one by one in this page. EPD Setting as shown below. 57 EPD-132 Board User Manual EPD-132 in ePaper Manager 1) EPD Connection Setting EPD Connection Setting feature is for users to wirelessly setup the group EPD SSID/ Password/IP and connect to a dedicated Router /gateway. There are two functions: "EPD setting" and "EPD Import" in EPD Connection Setting as shown below.
2) EPD Setting Below shows the EPD device information, including EPD device's Mac address, router SSID/password and Gateway IP. Though the default values are the same as below, the system offers four operations add node/edit/delete/reload settings as shown below. a. "Add EPD Node” button: Turns to general setting page as shown below. Users should see four written parameters. i.
59 EPD-132 Board User Manual EPD-132 in ePaper Manager As shown in the red box below, EPD nodes have four attributes representing EPD Mac address, AP SSID, AP password and gateway IP address respectively, and users should follow the format below . Chapter 4 3) EPD import 1. When multiple EPD devices need to be added into the EPD list, users can import a batch file to set it up. The file format can reference the template Node.json on the web page as shown below.
2. If the file uploads successfully, EPD device information is shown on screen. If the information does not display on the web page , please check file content for any error symbols. After importing files, users should click "Reload setting" to let the system apply it. 4.2.7 Hands-on Batch File WISE-3610W Installer 1) EPD Setting Installer SOP.
Chapter 4 EPD-132 in ePaper Manager Step 03: Click Reload setting button 2) EDP import Installer SOP. Follow these 2 steps to import the file.
Step 02: Click Reload setting button 4.3 Hands-on EPD Device on ePaper Manager The user needs to prepare before starting the ePaper manager/EPD controller as shown below. 1. EPD device mac address. 2. Target Item description data which needs to contain a unique ID as the key, e.g. StopID. 3. Target Item ID as the key, e.g. StopID. 4. EPD device screen typesetting as in the EPD image template.
Chapter 4 EPD-132 in ePaper Manager 4.3.
4.3.2 Add Group & Device into ePaper Manager 1. 2. Legal ePaper device joins the network Create group & edit group information 3.
Add Gateway / EPD device to Group. 5. Add Device into a Device Group 1) Click Device List on the side bar menu, and select the device group you want to add devices. Chapter 4 4.
2). Click add button on the top-left corner. 3). Choose the Hierarchical view. (If you have finished the White List Setting previously, you will see the devices grouped under a gateway.
Chapter 4 EPD-132 in ePaper Manager 4). Open the hierarchy until you see the device. Change the show number in order to select all devices under this gateway. 5). Select all by clicking the checkbox above.
6).Click the finish button to finish the selection.
Set Gateway Encrypted Key 1).Click Device List on the side bar menu, and select the device group with the router. 69 EPD-132 Board User Manual EPD-132 in ePaper Manager 2). Find the gateway device, and change to edit mode by clicking the edit button. Chapter 4 6.
3). Click the name of gateway device to enter edit mode. 4.) Fill in the Encrypted Key (32-characters with A-Z and 0-9), and then click send to finish the configuration.
Chapter 4 4.3.3 Design Your Own Template Label – Simply a text message Text – Its value comes from imported data, you can choose what column of data needs to be shown. Image – You can upload colorful images and it will automatically be transferred to red, black and white. Shape 71 EPD-132 Board User Manual EPD-132 in ePaper Manager Before delivering data to the EPD device, the user needs to design the template for the device to show the data on the screen.
– System supports rectangle, circles, and triangle shapes. Barcode – System supports Code 39 barcode QRcode 4.3.4 Import Item Data to ePaper Manager There are 2 way to to import data from vertical market application to our ePaper manager. 1) JSON Format : User sends out the API to update the data in real time. In order to import data to the EPD, below is the JSON format schema. You should reference below rules and prepare the data to upload your file.
Chapter 4 EPD-132 in ePaper Manager EPD-132 Board User Manual 73
4.3.5 Combine the Template and Item Data After importing data and making the template, we can combine them for regular data auto updates.
There are 2 parts in the management: Properties & Action 1) Properties: Users can read EPD device status atributes such as. EPD devices name Panel type Data page in device Electricity Connecting status Last update time 2) Action Action: Schedule – User needs to setup EPD device data delivery schedule: 75 EPD-132 Board User Manual EPD-132 in ePaper Manager Select correct account/group where your devices belong to. Select Preview / Edit mode. Chapter 4 4.3.
Device Task: Select Transmit – User needs to setup EPD device image flash schedule Device Task: Select Re-fresh Select EPD Device: select device to receive the schedule. Set Tag Template: select EPD Template from the list. Working Page: select which page in the EPD device. User may setup the schedule date and time from system.
Chapter 4 1. Select binding data icon. EPD-132 in ePaper Manager 2. Select data to bind. Note! User can import data and binding data into the EPD device via this web page. We also offer a mobile APP to bind device data and EPD.
3. Binding product item data with the APP. Install on Barcode scanner handset Use a barcode scanner: PWS-472 to scan the EPD device Mac address barcode and target product barcode. – Install on Barcode scanner handset – Use a barcode scanner : PWS-472 to scan the EPD device Mac address barcode and target product barcode ePaper Manager Associate App.
Chapter 4 EPD-132 in ePaper Manager Enter your Tag Code and Item Code information to bind.
User with the PWS-472 device can scan a barcode to quickly bring the Tag Code and Item Code information into the fields. A Bind Success! information window will show up. Click the transmit button to transmit the image to the tag device.
Chapter 4 A Transmit success! information window will show up. EPD-132 in ePaper Manager 4.
5. There are 4 actions for you to select.
83 EPD-132 Board User Manual EPD-132 in ePaper Manager 1) EPD device: Get, MAC address, ePaper record, and agent ID number. 2) Target Item Product: Get a physical Bus StopID as associate attribute 3) User need to associate the items above, the association is outlined in 4.2.7 above. 4) Bus Arriving Data needs to be included: field name: StopID and data: Stop0001 Chapter 4 4.3.
4.3.8 Smart Bus Stop Scenario 1. 2. 3. EPD device in standby Mode shows bus status. Government bus information server communicates with ePaper manager through Restful API. EPD device gets data every min to update bus info from ePaper manager. 4.3.9 Clear Events and Data of MongoDB 1. Click Setting – System on the side bar menu, and Click the Clear Data Button.
Clear device events: 1.) Open the Clear Device Events section. Chapter 4 2. 85 EPD-132 Board User Manual EPD-132 in ePaper Manager 2.) System automatically clearance. Change the Enable switch to ON, and select which days and how often the system will begin the clearance, and then click save button to finish configuration.
3.) Clear events manually. Select the clearance date (Reminder: the events between the date and before will be cleared), and click the Delete button to begin to clear data.
Clear operation/system events: 1.) Open the Clear Operation/System Events section. 87 EPD-132 Board User Manual EPD-132 in ePaper Manager 2.) System automatically clearance. Change the Enable switch to ON, and select which days and how often the ystem will begin clearance, and then click save button to finish this configuration. Chapter 4 3.
3.) Clear events manually. Select the clearance date (Reminder: the events between the date and before will be cleared), and click the Delete button to begin to clear data.
Chapter 4 EPD-132 in ePaper Manager 4. Clear device data: 1.) Open the Clear Device Data section.
2.) Automatic System clearance. Change the Enable switch to ON, and select which days and how the often system will begin the clearance, and then click save button to finish this configuration.
Chapter 4 3.) Clear events manually. Select the clearance date (Reminder: the data between the date and before will be cleared), and click the Delete button to begin to clear data.
4.4 Integrate EPD APIs into Your System We provide easy-to-use APIs to help you integrate into your own system. Below is a sample for you to understand and help integration into your system with our restful APIs. The vertical application needs to send the API to ePaper manager, sample code shown below. 1. Our API in Javascript: setItemData to update data into ePaper manager and ePaper manager will help forward the data to EPD.
var url = HOST + '/esl/v1/devicectrl/data'; var type = 'POST'; var data = {agentId: agentid, plugin: plugin, sensorIds: [{n: sensorId, v: sensorValue}]}; api(url, type, data, function(res){ console.log(JSON.stringify(res)); if(res && res.items && res.items.length > 0 && (res.items[0].statusCode === 202 || res.items[0].statusCode === 200)){ alert("Update Sensor Data Command Sended!") } else { alert("Ajax request error!"); } }); } For more API, user may check next chapter. 4.4.1 EPD Data Update API 1.
– code: string – name (group name): string – content: JSON string body(example) { "items": [ { "code": "X001", "name": "John", "content: "{"name": "John","age": "18"}" } ] } response(example) { "result": true } 3.
EPD-132 Board User Manual EPD-132 in ePaper Manager 95 Chapter 4 method: POST header: Basic Authorization body parameters: – agentid: string – templatename: string – body(example) (Notes: you must provide "agentid" or "did" in body, and for other parameters as follows, you only need to give at least one: "tid or templatename", "iid or itemcode", "mid") { "agentid": "00000001-0000-0000-0012-4b001557a500", "templatename": "Abnormal-English" } response(example) { "result": true } 8.
– content (optional): JSON string – refresh (optional, default: 1): number [available values: 1: Refresh after transmit, 0: Just store image to ESL tag memory] – page (optional, default: 0): number [available values: 0 ~ maxpagesize-1] body(example) { "agentid": "00000001-0000-0000-0012-4b001557aa72", "item": { "code": "Stop0001", "name": "Taipei 101", "content": "{\"Stop_Name\":\"Grand Hotel\", \"Route1 Name\":\"Test\"}" }, "refresh": 1, "page": 0 } response(example) { "itemStatus": "update item okay
Chapter 4 4.5 ePaper Manager Feature list 4.5.1 Component List Dashboard 4. schedule task effective schedule task: User can select current schedule in the system 97 EPD-132 Board User Manual EPD-132 in ePaper Manager 1. Device status: Provides EPD device status in system. 2. Battery status: Shows battery status on EPD device. 3. EPD Device: Show image update status.
EPD Controller EPD device search Search criteria Account/ Group/Connecting Status/ EPD Device Mode Properties Name / Panel type/ total page /Connecting status / Update Status EPD-132 Board User Manual 98
Chapter 4 Action Schedule Bind Item Available Target Product and Data User can manually bind/unbind ITEM DATA to the EPD device 1. Click the eye image icon. 2. Select the bind icon.l 3. System will pop-up another page for Available Target Product and Data. 99 EPD-132 Board User Manual EPD-132 in ePaper Manager User can setup SLEEP/ TRANSMIT/REFRESH as the scheduling task daily / weekly/ monthly /yearly.
Action Bind Template User can manually bind the Template to the EPD device Action Preview User can preview the EPD Device image. Transmit 1. User can re-flash the image on EPD device 2. User can Transmit image to EPD device 3. If user have click "transmit" or "re-flash" for the device, then the system keep busy , not response from device side. User can click "reset" to cancel the execution.
Chapter 4 Item Data Import ITEM Data EPD-132 in ePaper Manager Support CSV, EXCEL , JASON Format Add new data into current item Working Group 1. User can perform different working group in the same system. 2. User can add new group by click "Add" icon.
Device List Device search including EPD device, Router and Gateway. Search criteria Account/ Group/Connecting Status/ EPD Device Mode Action Remote control device: 1. Default column is Name and status message. 2. User can click icon at the right to select more fields: monitoring and Get/Set Data.
Chapter 4 User may save the template and then go to EPD controller to bind the template with EPD device. EPD-132 in ePaper Manager Template name: EPD Size ITEM DATA group Image direction Background color Display orientation Schematic view 1.EPD controller should setup the binding template. 1. Select on component 2. Right side shows the component properties.
1. Select on component 2. right side shows the component properties. 3.select the field “Value” and drop down menu shows data field from item data.
Chapter 4 White List Setting EPD-132 in ePaper Manager File format Epd-023,053 white list setting. User needs to import the device list and then the device can join the network.
OTA Upgrade Select upgrade device Package File preparing for the upgrade OTA Storage FTP & File path setting EPD-132 Board User Manual 106
Chapter 4 Setting Role EPD-132 in ePaper Manager Definition as below Super admin: Admin: Device admin: Account & Group Set the device into group. Email Service 1.
2.Click Email Service, and fill in the following form. 3.Setting successfully. 4.Add email account list for this service. Click Account button under the Setting List.
EPD-132 in ePaper Manager Add EPD connection number license. Clear Data User can query the event by clicking the calendar. 109 Chapter 4 5.Add an admin account. Click Save button. Email will send to this local user when event occurs.
Event User can query the event by clicking the calendar.
Chapter 5 5 WISE-EC EPD Designin Service
5.1 The Acquisition of Information Since ePaper is not a plug and play device, Advantech WISE-EC Design-in Services help customers to reduce the time and work involved with designing new ePaper devices.
Chapter 5 5.1.1 Design Design Guideline Support Multiple I/O extension Customized industrial design Optical bonding to improving image quality Wireless Conductive Measurement TX power / mask / RF harmonic tuning / RX sensitivity Design Assistance Service Advantech provides check list for engineer for easy check their schematics and also review service based on customer carrier board schematics. Those services are preventative, and help to catch design errors before they happen.
5.1.2 Integration Performance fine tuning SW integration from end-to-end Certification pre-scan Wireless & safety certification Integration stage This phase comprises of HW/SW integration, application development, and ePaper implementation. Due to the lack of knowledge and experience on plat- forms, customers need to spend a certain amount of time on analyzing integration problems.
Below is the contact information for Advantech customer service. Contact Information America Brazil 1-888-576-9688 0800-770-5355 Mexico 01-800-467-2415 Europe (Toll Free) 00800-2426-8080 Singapore & SAP 65-64421000 Malaysia 1800-88-1809 Australia (Toll Free) 1300-308-531800-810-0345 China (Toll Free) 800-810-8389Sales@advantech.com.
5.3.1.2 Repairs under Warranty It is possible to obtain a replacement (Cross-Shipment) during the first 30 days of the purchase, thru your original ADVANTECH supplier to arrange DOA replacement if the products were purchased directly from ADVANTECH and the product is DOA (Dead-on-Arrival). The DOA Cross-Shipment excludes any shipping damage, customized and/or build-to-order products.
117 EPD-132 Board User Manual WISE-EC EPD Design-in Service 5.3.2.3 Service Charges The product is excluded from warranty if: The product is repaired after expiry of the warranty period. The product is tested or calibrated after expiry of the warranty period, and a No Problem Found (NPF) result is obtained.
If a product has been repaired by ADVANTECH, and within three months after such a repair the product requires another repair for the same problem, ADVANTECH will do this repair free of charge.
Chapter 5 WISE-EC EPD Design-in Service EPD-132 Board User Manual 119
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
