MIC-3365 6U-sized Intel Pentium III/Celeron CPU board for CompactPCI™
Copyright Notice This document is copyrighted, 2000. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Product warranty Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events.
Packing List Before installing your board, ensure that the following materials have been received: • One MIC-3365 all-in-one single board computer • One utility CD-ROM disc • One 6-pin mini-DIN to PS/2 keyboard and PS/2 mouse cable • One heat sink plate • One optional bracket for mounting on-board hard disk drive and floppy disk drive • One hard disk drive (IDE) interface cable (44-pin) • One 26-pin FPC for floppy drive • One warranty certificate • This user's manual If any of these items are missing or dam
Contents Chapter 1 Hardware Configuration ..................................... 1 1.1 Introduction ..................................................................................... 2 1.2 Specifications ................................................................................... 3 1.2.1 Standard SBC functions ........................................................................ 3 1.2.2 VGA interface ....................................................................................... 4 1.2.
2.9 Ultra 2 SCSI Interface ................................................................... 23 2.10 Card Installation ........................................................................... 23 Chapter 3 Ethernet Software Configuration ..................... 25 3.1 Introduction ................................................................................... 26 3.2 Utility and Drivers ......................................................................... 26 3.3 Installation for Windows NT 4.0 ...
Appendix B Pin Assignments.............................................. 77 B.1 VGA Display Connector (CN2) ...................................................... 78 B.2 Keyboard and Mouse Connnector (CN7) ..................................... 78 B.3 COM1 and COM2 Serial Port (CN13 and CN6) ......................... 79 B.4 USB Connector (CN8) ................................................................... 80 B.5 Ethernet RJ-45 Connector (CN4 and CN5) .................................. 80 B.
Tables Table 1-1: MIC-3365 jumper descriptions .............................................. 8 Table 1-2: Clear CMOS ....................................................................... 10 Table 1-3: MIC-3365 connector descriptions ....................................... 11 Table 1-4: Recommended SDRAM ..................................................... 15 Table 2-1: MIC-3365 serial port default settings .................................. 22 Table B-1: MIC-3365 CRT display connector ..................
Figures Figure 1-1: MIC-3365 function block diagram ........................................ 6 Figure 1-2: MIC-3365 board dimensions ............................................... 7 Figure 1-3: MIC-3365 jumper locations ................................................. 8 Figure 1-4: MIC-3365 connector locations .......................................... 12 Figure 1-5: MIC-3365 front panel connector and indicator locations .... 13 Figure 1-6: Heat sink installation for 1 slot wide solution .................
CHAPTER Hardware Configuration 1
1.1 Introduction The MIC-3365 is a 6U-sized Intel® Pentium® III/CeleronTM CPU board and complies with PICMG 2.0 R2.1 CompactPCITM specifications. The MIC-3365 supports both FC-PGA Intel® Pentium® III Coppermine processors and Intel® CeleronTM processors. The MIC-3365 is available in three versions: MIC-3365, MIC-3365D, and MIC-3365F.
1.2 Specifications 1.2.1 Standard SBC functions • CPU: Intel® Socket 370 Pentium® III Coppermine CPU up to 700 MHz, Intel® Socket 370 CeleronTM CPU up to 566 MHz • BIOS: Award BIOS (Intel® FWH 4 Mb) • Chipset: Intel® 810 • System bus frequency: 100/66 MHz • Bus interface: 32-bit, 33 MHz, PICMG 2.
• USB interface: Two USB connectors with fuse protection. MIC-3365 and MIC-3365D provides one USB connector and MIC-3365F provides two USB connectors on the front panel • PCI-to-PCI bridge: One/Two Intel® DEC 21150 PCI bus controller chips, drive up to 7/14 PCI bus master peripherals. MIC-3365 and MIC-3365F support 7 PCI bus masters and MIC-3365D supports 14 PCI bus masters. 1.2.
• Humidity (operating and storage): 5 ~ 95% (non-condensing) • Board weight: 0.8 kg (1.8 lb) • Shock: 20 G (operating); 50 G (storage/transit) • Random vibration: 1.5 Grms 1.3 Safety Precautions Follow these simple precautions to protect yourself from harm and the products from damage. 1. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. 2.
1.
1.5 Board Dimensions 160 mm 233.
1.6 Jumpers 1.6.1 Jumper Locations The MIC-3365 provides jumpers for configuring your board for specific applications other than the default settings. Table 1-1 list the jumper functions. Figure 1-3 illustrates the jumper locations. The default jumper setting is illustrated in Figure 1-3.
1.6.2 Jumper Settings This section tells how to set the jumpers to configure your card. It gives the card default configuration and your options for each jumper. After you set the jumpers and install the card, you will also need to run the BIOS Setup program (discussed in Chapter 6) to configure the serial port addresses, floppy/hard disk drive types and system operating parameters. Connections, such as hard disk cables, appear in Chapter 2.
1.6.3 Clear CMOS (JP5) This jumper is used to erase CMOS data and reset system BIOS information. Follow the procedures below to clear the CMOS. 1. Turn off the system. 2. Close jumper JP5 (2-3) for about 2-3 seconds. 3. Close jumper JP5 (1-2). 4. Turn on the system. The BIOS is reset to its default setting.
1.7 Connectors On-board connectors link to external devices such as hard disk drives, keyboards, or floppy drives, etc. Table 1-3 lists the function of each connector and Figure 1-4 and Figure 1-5 illustrate each connector location. Chapter 2 gives instructions for connecting external devices to your card.
Figure 1-4: MIC-3365 connector locations 12 MIC-3365 User's Manual
LAN1 LAN1 Front Panel Connectors and Indicators TM LAN2 LAN1 LAN2 LAN2 USB USB COM1 COM1 USB COM1 COM2 PRINTER PRINTER PRINTER 1.
1.9 Installing SDRAM (DIMMs) The MIC-3365 provides two 168-pin DIMM sockets. Each socket accepts either 16, 32, 64, 128 or 256 MB SDRAM. The sockets can be filled in any combination with DIMMs of any size, giving a total memory capacity between 16 and 512 MB. Since the MIC-3365 can operate at 66 or 100 MHz, we recommend using PC100-compliant DIMMs. The procedure for installing DIMMs appears below. Please follow these steps carefully. 1. Ensure that all power supplies to the system are switched Off. 2.
Note: To ensure compatibility between the MIC-3365 and DRAMmodules, our R&D team has compiled a list of recommended SDRAMs. Only those which have passed the team’s strict and rigorous testing procedures are included. Please refer to the table below. You may order the SDRAMs locally or from Advantech. If you want to buy from us, please contact Advantech’s sales representatives for details.
1.10 Installing CPU heat sink and HDD, FDD brackets The MIC-3365 accepts Intel® socket 370 Pentium® III Cuppermine CPU or Intel® socket 370 CeleronTM CPU. In order to meet critical environmental conditions and the physical space of the MIC-3365 at the same time, Advantech designed a heat sink to fulfill both needs. Please refer to Figure 1-6 for an illustration of the heat sink used for the MIC-3365 and MIC-3365D, 1-slot wide solution.
Figure 1-7: Heat sink installation for 2 slot wide solution Chapter 1 Hardware Configuration 17
1.11 Software Support The MIC-3365 supports lots of operating systems, such as Microsoft Windows family, Linux, SCO UNIX, QNX, etc. Note: 18 At the beginning of QNX installation process, please follow the system's installation guide shown on the screen. Press anykey and F2 when asked, and then choose VGA 16 Color Only, and press to continue. Otherwise, you won't be able to contiune installing QNX.
CHAPTER Connecting Peripherals 2
2.1 IDE Device (CN12) The MIC-3365 provides two IDE (Integrated Device Electronics) channels via the J3 connector to the rear transition board MIC-3302. Four IDE drives can be connected to the MIC-3365 through the rear transition board MIC-3302. The MIC-3365F provides a mounting bracket to mount a 2.5" hard disk drive on board. Users can connect this 2.5" hard disk drive to the on-board 44-pin IDE connector (CN12). Users can connect two IDE drives to each IDE channel.
2.3 VGA Display Connector (CN2) The MIC-3365 provides an VGA chipset built-in display for high performance application. The MIC-3365's CN2 is a DB-15 connector for VGA monitor input. Pin assignments for the VGA display are detailed in Appendix A. 2.4 Parallel Port Connector (CN1) The parallel port is normally used to connect the CPU board to a printer. The MIC-3365 includes an on-board parallel port, accessed through a DB 25-pin connector, CN1, on the front panel.
The IRQ and address range for both ports are fixed. However, if you wish to disable the port or change these parameters later, you can do this in the system BIOS setup. The table below shows the settings for the MIC-3365 board's ports: Table 2-1: MIC-3365 serial port default settings Port COM1 COM2 2.
2.9 Ultra 2 SCSI Interface The MIC-3365 and MIC-3365F provides an Ultra 2 SCSI interface on the rear transition board MIC-3302 via the J5 connector. The MIC-3302 has a 68-pin, dual in-line connector for Ultra 2 SCSI devices. Connection of SCSI devices requires special attention, especially when determining the last drive on the SCSI chain. Refer to Chapter 5 and your device's operating manual for detailed installation advice. 2.
the card guide and repeat step 3 again. Do not try to install a card by forcing it into the chassis. 5. Pull the upper handle down and lift the lower handle up to push the card into place. 6. Secure the card by pushing in the red handle to lock it into place. To remove a card: 1. Unscrew the screws on the front panel. Pull out the red portion in the middle of the handle to unlock the handle. 2. Lift the upper handle up and press the lower handle down to release the card from the backplane. 3.
CHAPTER 3 Ethernet Software Configuration
3.1 Introduction The MIC-3365 has two on-board high-performance fast Ethernet interfaces which comply with IEEE 802.3/802.3u for 10Base-T and 100 Base-TX data rates. The module uses two Intel® 82559 fast Ethernet controllers with integrated PHY and is compatible with the Intel® PRO/100+ Server and Client Adapter. The dual Ethernet channel design provides several options for increasing throughput and fault tolerance when running Windows NT 4.0 or NetWare 4.
Microsoft Windows • \MIC3365\LAN\E100BNT.SYS (NDIS 4.0), \MIC3365\LAN\ OEMSETUP.INF: Drivers for Windows NT 4.0 • \MIC3365\LAN\E100B.SYS (NDIS 3), \MIC3365\LAN\ OEMSETUP.INF: Drivers for Windows NT 3.51 • \MIC3365\LAN\NET82557.INF: Drivers for Windows 98 • \MIC3365\LAN\E100BNT.SYS (NDIS 4.0), \MIC3365\LAN\ NET82557.INF: Drivers for Windows 95 • MIC3365\LAN\WFW\E100B.38_, \MIC3365\LAN\WFW\ OEMSETUP.INF: Drivers for Windows 3.1 For Novell NetWare • \MIC3365\LAN\INFO\NETWARE\NETWARE.
support for AS/400 and NetWare (for ODINSUP) • \MIC3365\LAN\OS2\E100B.OS2: Drivers for LAN server (OS/2 driver) • \MIC3365\LAN\DOS\E100B.DOS: Drivers for LAN server (DOS driver) • \MIC3365\LAN\DOS\E100B.DOS: Drivers for BANYAN NDIS workstation • \MIC3365\LAN\DOS\E100B.DOS: Drivers for LANTASTIC 6.0 • \MIC3365\LAN\DOS\E100B.DOS: Drivers for general NDIS 2.X (DOS driver) • \MIC3365\LAN\OS2\E100B.OS2: Drivers for general NDIS 2.
3.3 Installation for Windows NT 4.0 Before installing; create a new folder [!] ,\MIC3365\LAN\, in your "E:" drive on your hard disk drive, and download all files from the directory, \MIC3365\LAN\, on the utility CD-ROM to it. 1. In the Windows NT screen, select "Start", click "Settings". Click the "Control Panel" item and choose "Network". 2. Click "Yes".
3. Click "Wired to the Network", or users may choose "Remote access to the network" if applicable. 4. Click "Select from list".
5. Click "Have Disk". 6. Type in "E:\MIC3365\LAN" in the blank column and click "OK".
7. Click "OK". 8. Click "Next".
9. Click "Next". 10. Click "Next".
11. Click "Next". 12. Insert Windows NT source disc in drive E. Type "E:\I386" in the blank column or any other directory that contains the Windows NT files. Click "Continue".
13. Wait for the installation to finish. 14. Complete the settings with users' network settings. Click "OK".
15. Click "Next". 16. Click "Next".
17. Click "Yes" to restart the computer and enable the changes to take effect.
38 MIC-3365 User's Manual
CHAPTER 4 AGP VGA Setup
4.1 Introduction The MIC-3365 uses chipset built-in AGP VGA display. This chapter describes how to install the VGA drivers to the MIC-3365. 4.2 Installation of SVGA Driver The MIC-3365 is supplied with a utility CD-ROM disc that holds the necessary files for setting up the VGA display under the directory \MIC-3365\VGA. The contents and path names of this directory are listed below: • MIC3365\VGA\Win311: VGA utility for Windows 3.
4.3 Installation for Windows NT 4.0 1. Insert the utility CD-ROM disc in the CD-ROM drive and wait for the auto-run screen to pop up. Click "Install Drivers". 2. Click "MIC-3000 Series".
3. Click "MIC-3365". 4. Under VGA Drivers menu, click "Browse" to choose the operating system used.
5. Click "Nt40". 6. Click "Graphics".
7. Click "Setup.exe". 8. Click "Next".
9. Click "Yes". 10. Click "Next" to install drivers.
11. Wait for installation to finish. 12. Click "Finish" to restart the computer and enable the changes to take effect.
CHAPTER SCSI Software Configuration 5
5.1 Introduction The MIC-3365 uses the Symbios SYM53C895 SCSI processor to provide an Ultra 2 SCSI interface on the rear transition board MIC-3302 via the J5 connector. The Ultra 2 SCSI interface has a data transfer rate up to 80 MB/s. The device can support cables up to 12-meter long and up to 16 LVD devices on a wide LVD ( Low Voltage Differential) SCSI bus. Device drivers and utilities for DOS, Windows 95/98/NT, OS/2, SCO UNIX, UnixWare and NetWare are included in the utility CD-ROM disc. 5.
For OS/2: • \MIC3365\SCSI\OS2\OS2.TXT: Installation instructions for OS2 • \MIC3365\SCSI\OS2\SYM8XXPC.EXE, \MIC3365\SCSI\OS2\SYM_HIPC.EXE: Drivers for OS2 Note: The installation procedures below assume users' CDROM drive name is E.
5.3 Installation for Windows NT 4.0 1. In the Windows NT screen, select "Start", click "Settings". Click the "Control Panel" item and choose "SCSI Adapters". 2. Click "Add".
3. Click "Have Disk". 4. Click "Browse".
5. Click "Cancel". 6. Click "My Computer".
7. Click "Drv_Bank (E)". 8. Click "MIC3365".
9. Click "SCSI". 10. Click "Winnt".
11. Click "Oemsetup". 12. Click "OK".
13. Click "OK". 14. Click "Continue".
13. Click "Yes" to restart the computer and enable the changes to take effect.
58 MIC-3365 User's Manual
CHAPTER 6 Award BIOS Setup
6.1 Introduction Award's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS so that it retains the Setup information when the power is turned off. 6.2 Entering Setup Turn on the computer and check for the "patch code". If there is a number assigned to the patch code, it means that the BIOS supports your CPU.
6.3 Standard CMOS Features Choose the "STANDARD CMOS FEATURES" option from the INITIAL SETUP Menu, and the screen below will be displayed. This standard setup menu allows users to configure system components such as date, time, hard disk drive, floppy drive, display, and memory.
6.4 Advanced BIOS Features The "ADVANCED BIOS FEATURES" screen will appear after choosing the ADVANCED BIOS FEATURES item from the INITIAL SETUP Menu. This screen allows users to configure the MIC-3365 according to their particular requirements.
CPU L2 Cache ECC Checking This option controls the ECC capability in the CPU level 2 cache. Quick Power On Self Test This option speeds up the Power-On Self Test (POST) conducted as soon as the computer is turned on. When enabled, the BIOS shortens or skips some of the items during the test. When disabled, normal POST procedures resume. First/Second/Third Boot Devices These options determines the boot up sequence.
Typematic Rate Setting The typematic rate determines the characters per second accepted by the computer. Typematic Rate setting enables or disables the typematic rate. Typematic Rate (Char/Sec) BIOS accepts the following input values (character/second) for Typematic Rate: 6, 8, 10, 12, 15, 20, 24, 30. Typematic Delay (msec) When holding down a key, the Typematic Delay is the time interval between the appearance of the first and second characters.
6.5 CHIPSET Features Setup Choose the "ADVANCED CHIPSET FEATURES" option from the INITIAL SETUP Menu, and the screen below will be displayed. This sample screen contains the manufacturer's default values for the MIC-3365. 6.
6.7 Power Management Setup The power management setup controls the CPU cards' "green" features. The following screen shows the manufacturer's default values. Figure 6-5: Integrated Peripherals screen Note: 66 If you enable the IDE HDD block mode, the enhanced IDE driver will be enabled.
6.8 PnP/PCI Configurations Figure 6-6: Power Management Setup screen Power Management This option allows you to determine if the values in power management are disabled, user-defined, or predefined. HDD Power Management You can choose to turn the HDD off after one of the time intervals listed, or when the system is in Suspend mode. If in a power saving mode, any access to the HDD will wake it up. Note: The HDD will not power down if the Power Management option is disabled.
6.9 Load Optimized Defaults "LOAD OPTIMIZED DEFAULTS" loads the most appropriate values of the system parameters for maximum performance.
6.10 Set Password To change, confirm, or disable the password, choose the "SET PASSWORD" option from the INITIAL SETUP menu, and press [Enter]. The password can be at most 8 characters long. Remember to enable this feature. You must first select the "SECURITY OPTION" in the ADVANCED BIOS FEATURES to be either "Setup" or "System." Pressing [Enter] again without typing any characters can disable the password setting function.
6.11 Save & Exit Setup If you select this and press the [Enter] key, the values entered in the setup utilities will be recorded in the CMOS memory of the chipset. The microprocessor will check this every time you turn your system on and compare this to what it finds as it checks the system. This record is required for the system to operate.
6.12 Exit Without Saving Selecting this option and pressing the [Enter] key lets you exit the Setup program without recording any new values or changing old ones.
72 MIC-3365 User's Manual
APPENDIX A Programming the Watchdog Timer
A.1 Programming the Watchdog Timer To program the watchdog timer, you must write a program which writes a value to I/O port address 444 (hex). This output value represents time interval. The value range is from 01 (hex) to 3F (hex), and the related time interval is 1 sec. to 63 sec. Data Time Interval 01 1 sec. 02 2 sec. 03 3 sec. 04 4 sec. • • • • • • 3F 63 sec.
After data entry, your program must refresh the watchdog timer by rewriting the I/O port 444 (hex) while simultaneously setting it. When you want to disable the watchdog timer, your program should read I/O port 444 (hex).
7 6 MIC-3365 User's Manual
APPENDIX B Pin Assignments
B.1 VGA Display Connector (CN2) 1 5 6 10 15 11 Table B-1: MIC-3365 CRT display connector Pin 1 2 3 4 5 6 7 8 Signal RED GREEN BLUE N/C GND GND GND GND Pin 9 10 11 12 13 14 15 Signal VGAVCC GND N/C SDA HSYNC VSYNC SCL B.
9 6 9 8 7 6 1 5 4 3 2 1 5 B.
B.4 USB Connector (CN8) 1 4 USB2 USB1 Table B-4: MIC-3365 USB1/USB2 connector Pin 1 2 3 4 USB1 Signal VCC USBD0USBD0+ GND Pin 1 2 3 4 USB2 Signal VCC USBD1USBD1+ GND B.
B.
B.7 IDE Connector (CN12) 43 41 .... 3 1 44 42 ....
B.8 Floppy Drive Connnector (CN11) 1 2 ....
B.9 System I/O Ports Table B-9: System I/O ports Addr.
B.10 DMA Channel Assignments Table B-10: DMA channel assignments Channel 0 1 2 3 4 5 6 7 Function Available Available Floppy disk (8-bit transfer) LPT1 Cascade for DMA controller 1 Available Available Available B.
B.12 1st MB Memory Map Table B-12: 1st MB memory map Addr.
B.
B.
B.
B.
B.
92 MIC-3365 User's Manual
